HP Kayak XW 04xx Manual de usuario

HP Kayak XW Series 0480 PC Workstation—

HP VISUALIZE fx6 Texture Module

Mil_fx6.fm Page 1 Friday, February 26, 1999 8:46 AM

HP Kayak XW Series 0480 PC Workstation — HP VISUALIZE fx6 Texture Module

Important Safety Instructions

Please read the following safety information first.

CAUTION Static electricity can damage electronic components.

Use an electrostatic bracelet if you have one.

Turn all equipment OFF. Don’t let your clothes touch the accessory.

To equalize the static electricity, rest the accessory bag on top of the PC

while you are removing the accessory from the bag. Handle the

accessory as little as possible and with care.

WARNING For your safety, never remove the PC’s cover without first removing

the power cord from the power outlet, and any connection to a

telecommunications network. Always replace the cover on the PC

before switching it on again.

Before handling the VISUALIZE fx6 graphics board, first wait until the

board has cooled down completely before touching it. The graphics

board can become very hot during use.

Mil_fx6.fm Page 2 Friday, February 26, 1999 8:46 AM

English 3

HP Kayak XW Series 0480 PC Workstation — HP VISUALIZE fx6 Texture Module

Introduction

The HP VISUALIZE fx6 Texture Module is an add-on accessory for the

HP VISUALIZE fx6 graphics board.

The HP VISUALIZE fx6 Texture Module provides:

•Accelerated hardware texture mapping

•32 MB dedicated SDRAM (Synchronous DRAM) memory

for textures.

HP VISUALIZE fx6 Graphics Board

(without Texture Module installed)

Texture Module (HP D6795A)

Mil_fx6.fm Page 3 Friday, February 26, 1999 8:46 AM

HP Kayak XW Series 0480 PC Workstation — HP VISUALIZE fx6 Texture Module

Installing the Texture Module

CAUTION Be very careful when handling the VISUALIZE fx6 board. Bumping,

bending or dropping the board can cause irreparable damage.

Removing the VISUALIZE fx6 Graphics Board

1Switch off the display and PC Workstation, and disconnect all power

cords and any telecommunication cables.

2Remove the PC Workstation’s cover (refer to the User’s Guide that

came with your PC Workstation).

3Carefully place the PC Workstation on its side.

Your PC Workstation may look

different to the one documented here.

Mil_fx6.fm Page 4 Friday, February 26, 1999 8:46 AM

English 5

HP Kayak XW Series 0480 PC Workstation — HP VISUALIZE fx6 Texture Module

Installing the Texture Module

WARNING Before handling the VISUALIZE fx6 graphics board, first wait until the

board has cooled down completely before touching it. The graphics

board can become hot during use.

4Remove the two accessory slot screws and the retaining screw that

holds the board in place and, carefully ease the board up and out of

the PC Workstation’s case using the board’s strengthening bar.

CAUTION When sliding the board up, ensure that the board does not snag or catch

against the PC Workstation’s case or cables.

5Place the board on a clean, dry surface.

Strengthening bar

Two accessory

slot screws

Board-retaining screw

Mil_fx6.fm Page 5 Friday, February 26, 1999 8:46 AM

HP Kayak XW Series 0480 PC Workstation — HP VISUALIZE fx6 Texture Module

Installing the Texture Module

Adding the Texture Module to the VISUALIZE fx6 Board

1Remove the two screws from the board’s strengthening bar, and then

remove it from the VISUALIZE Fx6 board. (You can use a TorxTM

screwdriver or a flat-blade screwdriver of the correct size.)

2Using both hands, carefully remove the terminator from the

VISUALIZE fx6 board. Store the terminator in a safe place (you may

need it at a later date).

3Before installing the texture module, ensure that all four screws on

the texture module are fully retracted or removed.

Terminator

Strengthening Bar

Mil_fx6.fm Page 6 Friday, February 26, 1999 8:46 AM

English 7

HP Kayak XW Series 0480 PC Workstation — HP VISUALIZE fx6 Texture Module

Installing the Texture Module

4Carefully line up the connectors on the texture module and the

VISUALIZE fx6 board. Then using both thumbs, press the texture

module into place.

5Ensure that the texture module is properly connected before

securing it into place with the screws provided.

Texture Module

Connectors

VISUALIZE fx6

Connectors

Mil_fx6.fm Page 7 Friday, February 26, 1999 8:46 AM

HP Kayak XW Series 0480 PC Workstation — HP VISUALIZE fx6 Texture Module

Installing the Texture Module

Replacing the VISUALIZE fx6 Graphics Board

1First ensure that the system board data cables are correctly routed

and flat against the system board so that they do not obstruct the

VISUALIZE fx6 graphics board.

2Hold the board with both hands and carefully slide it down toward

the accessory slots’ connectors.

TIP When sliding the board down, ensure that the board does not snag or

catch against the PC Workstation’s case.

3Align the board’s two connectors with the two accessory slot

connectors and push the board firmly into the position.

4Ensure that the board’s connectors are fully connected before

securing it with the two accessory slot screws, and the retaining

screw the holds the board in place (refer to the graphic on page 5 to

locate these screws).

5Replace the PC Workstation’s cover. Reconnect all cables and power

cords.

Mil_fx6.fm Page 8 Friday, February 26, 1999 8:46 AM

English 9

HP Kayak XW Series 0480 PC Workstation — HP VISUALIZE fx6 Texture Module

Checking the Installation

The fx6 texture module is automatically detected by the VISUALIZE

fx6 driver. No software configuration is necessary. To check that the

texture module is correctly installed:

1Switch on your PC Workstation.

2When in Windows NT, open the Display Properties window by clicking

the Start button, selecting Settings / Control Panel, then double-clicking

Display.

3Click the About tab.

If the texture module was correctly installed, the About window will

contain the text: Hardware Texture Mapping: Installed.

To check that you have the latest version of this driver, refer to HP’s

web site at: http://www.hp.com/go/kayaksupport.

Indicates that the texture

module is correctly installed

Indicates the version of

the driver installed

Mil_fx6.fm Page 9 Friday, February 26, 1999 8:46 AM

HP Kayak XW Series 0480 PC Workstation — HP VISUALIZE fx6 Texture Module

Hardware Warranty

This HP accessory is covered by a limited hardware warranty for a

period of one year from the date of purchase by the original end-user.

The type of service provided is return to an HP or repair-authorized

reseller service-center.

At Hewlett-Packard’s discretion, a defective accessory will be repaired

or replaced by a new unit, either of the same type or of an equivalent

model.

If this accessory is purchased and used together with an HP Vectra

personal computer or an HP Kayak PC Workstation, it will be covered

by the warranty of this computer or workstation, under the same

conditions of service and duration.

Please refer to the warranty statement provided with your HP personal

computer or PC Workstation for warranty limitations, customer

responsibilities, and other terms and conditions.

FOR CONSUMER TRANSACTIONS IN AUSTRALIA AND NEW

ZEALAND: THE WARRANTY TERMS CONTAINED IN THIS

STATEMENT, EXCEPT TO THE EXTENT LAWFULLY PERMITTED,

DO NOT EXCLUDE, RESTRICT OR MODIFY AND ARE IN ADDITION

TO THE MANDATORY STATUTORY RIGHTS APPLICABLE TO THE

SALE OF THIS PRODUCT TO YOU.

Mil_fx6.fm Page 10 Friday, February 26, 1999 8:46 AM

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de De oficina de HP

HP dc72 - Blade Workstation Client Manual de operación y mantenimiento

HP xw9400 Instrucciones de instalación

HP T200 Hoja de especificaciones

HP Vectra XU 6/XXX Manual de usuario

HP 282 Pro G3 Instrucciones de instalación

HP 260 G2 DM Manual

HP Z1 Instrucciones de montaje

HP Pavilion t400 - Desktop PC Instrucciones de instalación

HP Brio 81XX Manual de usuario

HP Pavilion t480 Manual de usuario

HP DL320 - ProLiant - G3 Instrucciones de funcionamiento y seguridad

HP Model 748 - VME Workstation Manual de usuario

HP Kayak XU 04xx Instrucciones de funcionamiento

HP ZBook x2 Manual

HP 512n - Pavilion - 128 MB RAM Manual de usuario

HP xw8600 - Workstation Manual de usuario

HP ZX2000 Manual de usuario

HP Pavilion a210 Manual de usuario

HP ProLiant xw2x220c - Blade Workstation Manual de servicio

HP COMPAQ 8000 Manual de operación y mantenimiento

HP Vectra XM5 3 Manual

HP A1210n - Pavilion - 512 MB RAM Manual de usuario

HP Compaq SP700 Manual de usuario

HP P6230F Pavilion PC Manual de usuario

Manuales populares de De oficina de otras marcas

Asus

Asus E210 Series Manual de usuario

Dell

Dell Inspiron 600m Manual de usuario

Dell

Dell Inspiron 3662 Manual de usuario

TotalFlow

TotalFlow uFLO Manual de usuario

Logitech

Logitech MK320 Manual de usuario

Dell

Dell XPS 730 H2C Manual de usuario

Sony

Sony Vaio Series Manual de usuario

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Manual de usuario

Alto

Alto MD 250 Manual de usuario

Lenovo

Lenovo ThinkCentre Edge 72 Manual

Lenovo

Lenovo ThinkStation D20 Manual

Arbor Technology

Arbor Technology FPC-7800 Series Manual de usuario

Sony

Sony VAIO VGX-TP1 Series Manual de usuario

Asus

Asus Eee Box B204 Manual de usuario

Dell

Dell Optiplex 9010 All In One Manual de usuario

Everex

Everex eXplora Manual de usuario

Lenovo

Lenovo ThinkCentre M75e Manual de usuario

Dell

Dell Alienware Area-51 R4 Manual de usuario