HP dx5150 Series Instrucciones de instalación
HP-00007-01, Appendix 3 02-Jun-2005
HP Restricted
Page 1
Appendix 3 Product End-of-Life Disassembly instructions
Product Identification:
Marketing Name / Model Description
HP Business Desktop dx5150 Series Small Form Factor, ATX board
Purpose: The document is intended for use by end-of-life recyclers or treatment facilities. It provides the
basic instructions for the disassembly of HP products to remove components and materials requiring
selective treatment.
1.0 Items Requiring Selective Treatment
1.1 Items listed below are classified as requiring selective treatment.
1.2 Enter the quantity of items contained within the product which require selective treatment in
the right column, as applicable.
Item Description
Notes
Qty items in
product.
Printed Circuit Boards (PCB) or Printed
Circuit Assemblies (PCA)
With a surface greater than 10
square cm
2 (sys board &
P/S board)
Batteries All types including standard
alkaline and lithium coin or button
style batteries
1
Mercury containing components For example, mercury in lamps,
display backlights, scanner lamps,
switches, batteries
0
Liquid Crystal Displays (LCD) with a
surface greater than 100 square cm
Includes background illuminated
displays with gas discharge lamps
0
Cathode Ray Tubes (CRT) 0
Capacitors / condensers (Containing
PCB / PCT)
0
Electrolytic Capacitors / Condensers
measuring greater than 2.5 cm in
diameter or height
3 (3 in P/S)
External electrical cables and cords 0
Gas Discharge Lamps 0
Plastics containing Brominated Flame
Retardants
0
Components and parts containing toner
and ink, including liquids, semi-liquids
(gel/paste) and toner
Include the cartridges, print
heads, tubes, vent chambers, and
service stations.
0
Components and waste containing
asbestos
0
Components, parts and materials
containing refractory ceramic fibers
0
Components, parts and materials
containing radioactive substances
0
HP-00007-01, Appendix 3 02-Jun-2005
HP Restricted
Page 2
2.0 Tools Required
List the type and size of the tools that would typically be used to disassemble the product to a
point where components and materials requiring selective treatment can be removed.
Tool Description Tool Size (if applicable)
Torx Screw Driver
Dikes (Figure 17)
3.0 Product Disassembly Process
3.1 List the basic steps that should typically be followed to remove components and materials
requiring selective treatment:
SYSTEM BOARD
1 To remove the access panel (see Figure 1 below):
a. Pull up and hold open the latch on the top of the computer.
b. Slide the access panel back about 1.3 cm (0.5 inch), and then lift it off of the unit.
2 To remove the front bezel (see Figure 2 below):
a. Pull up on the three release tabs on the top of the bezel.
b. Pull the front bezel away from the chassis.
3 Rotate the drive cage to its full upright position (see Figure 3 below).
4 Unplug all cables from the system board (see Figure 4 below).
5 To remove the heatsink assembly (see Figures 5 & 6 below):
a. Loosen the two captive screws that secure the heatsink to the system board.
b. Twist the heatsink slightly to break the bond between it and the processor then, and
then lift the heatsink from the processor.
6 To remove the processor (see Figure 7 below):
a. Rotate the socket handle to its fully open position.
b. Lift the processor from the system board.
7 To remove the system board (see Figures 8 & 9 below):
a. Remove the eight screws that secure the system board to the chassis.
b. Slide the system board toward the front of the computer until the rear I/O connectors
clear the chassis, and then remove the system board from the chassis.
POWER SUPPLY PCA
1 Make sure the drive cage is rotated to its fully upright position, and then disconnect all
power cables from all devices.
2 To remove the power supply (see Figure 10 below):
a. Remove the three screws that connect the power supply to the chassis.
b. Slide the power supply forward about 0.95 cm (3/8 inch), lift it to clear the guides on the
floor of the chassis, and then pivot the top of the power supply to clear the top chassis lip.
3 Cut the tie-wrap (see Figure 11 below).
HP-00007-01, Appendix 3 02-Jun-2005
HP Restricted
Page 3
POWER SUPPLY PCA (
continued
)
4 Remove the cover from the power supply by removing the screws from the power supply
surface, and then lifting the cover off of the power supply (see Figure 12 below).
5 Cut the two cables that connect the Switch (see Figure 13 below).
6 Cut the two cables that connect the Inlet (Figure 14 below).
7 Remove the power supply PCA from the power supply (see Figure 15 below).
8 Cut the capacitors (C4, C5) solder joint (see Figure 16 below) using dikes (see Figure 17
below), and then remove the capacitors.
9 Cut the capacitor (C11) solder joint using dikes, and then remove the capacitor (see
Figure 18 below).
BATTERY
1 Locate the battery and battery holder on the system board.
2 Depending on the type of battery holder on the system board, complete the following
instructions to replace the battery:
Type 1 Battery Holder (see Figure 19 below)
- Lift the battery out of the holder.
Type 2 Battery Holder (see Figure 20 below)
- To release the battery from the holder, squeeze the metal clamp that extends above one
edge of the battery. When the battery pops up, lift it out.
HP-00007-01, Appendix 3 02-Jun-2005
HP Restricted
Page 4
3.2 Illustrations
FIGURE 1: Removing the access panel
FIGURE 2: Removing the front bezel
FIGURE 3: Rotating the drive cage
FIGURE 4: System board
HP-00007-01, Appendix 3 02-Jun-2005
HP Restricted
Page 5
FIGURE 5: Removing the heatsink FIGURE 6: Removing the heatsink assembly
FIGURE 7: Removing the processor
FIGURE 8: System board screw locations
FIGURE 9: Removing the system board
FIGURE 10: Removing the power supply
HP-00007-01, Appendix 3 02-Jun-2005
HP Restricted
Page 6
FIGURE 11: Tie wrap
FIGURE 12: Power supply with cover removed
FIGURE 13: Switch cables
FIGURE 14: Inlet cables
FIGURE 15: Power supply PCA
FIGURE 16: C4 and C5 capacitors
HP-00007-01, Appendix 3 02-Jun-2005
HP Restricted
Page 7
FIGURE 17: Dikes
FIGURE 18: C11 capacitor
FIGURE 19: Type 1 battery holder
FIGURE 20: Type 2 battery holder
Otros manuales para dx5150 Series
1
Tabla de contenidos
Otros manuales de De oficina de HP
HP
HP Pavilion 304 Manual de usuario
HP
HP dx2009 - Very Small Form Factor PC Instrucciones de uso
HP
HP 512n - Pavilion - 128 MB RAM Manual de usuario
HP
HP Xw4550 - Workstation - 2 GB RAM Manual de usuario
HP
HP SignagePlayer mp8200 Manual de operación y mantenimiento
HP
HP dc7900 - Convertible Minitower PC Manual de usuario
HP
HP Kayak XW A2-U2-W2 Manual
HP
HP Presario SR1200 - Desktop PC Manual de usuario
HP
HP Compaq Presario Manual
HP
HP E-PC C10 Manual de usuario
HP
HP Pavilion w5100 Manual de usuario
HP
HP Pavilion Elite m9165 Manual de usuario
HP
HP VH677UA#ABA - Pavilion Dv6-1244sb... Hoja de especificaciones
HP
HP Compaq Notebook Instrucciones de instalación
HP
HP DF300A - Portable Digital Picture Frame Manual de usuario
HP
HP Compaq Presario Instrucciones de instalación
HP
HP Pavilion p7-1200 Manual de uso y mantenimiento
HP
HP 3350 - Cisco NAC Appliance Manual de instrucciones
HP
HP Pavilion 400 - Desktop PC Instrucciones de instalación
HP
HP Spectre x360 Convertible Manual
