HP Integrity cx2600 Manual de usuario

HP Server Mount Kit AB292A

for 19 in. 2-Post Rack

Installation Instructions

Manufacturing Part Number: AB292-96001

April 2004

U.S.A.

Legal Notices

The information contained herein is subject to change without notice. The only warranties for HP products

and services are set forth in the express warranty statements accompanying such products and services.

Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for

technical or editorial errors or omissions contained herein.

Reproduction, adaptation, or translation of this document without prior written permission is prohibited,

except as allowed under the copyright laws.

Printed in the U.S.A.

Related Documents. The latest versions of server documents, and any updates to these documents are

posted under the appropriate server at http://docs.hp.com. For online access to technical support information,

self-solve tools, online assistance, community forums of IT experts, broad multi vendor knowledge base, and

monitoring and diagnostic tools, go to http://www.hp.com/support.

Chapter 1 3

1HP Server Mount Kit for 19 in. 2-Post Rack

Installation Instructions

Introduction

This manual provides instructions for installation of the hp Integrity cx2600 server chassis in a 19 in.

2-column rack, with column widths of 3 to 9 inches.

Cabinet Safety Precautions

WARNING Ensure that the rack is level and stable before working on the rack. Be sure the

leveling jacks (feet) extend to the floor and that the full weight of the rack rests

firmly on the floor.

WARNING Ensure that the rack has anti-tip measures in place. Such measures may include

floor-bolting, anti-tip feet, ballast, or a combination of these measures as specified by

the rack manufacturer and applicable codes.

WARNING Be sure that adequate personnel are on hand to support the product(s) during the

installation process. Use of the appropriate lifting device is recommended as an

installation aid.

WARNING Always load the rack from the bottom up. Load the heaviest items in the rack first.

This makes the rack bottom-heavy and helps prevent the rack from becoming

unstable.

WARNING Do not overload the branch circuit that provides power to the rack. The total rack

load should not exceed 80% of the branch circuit rating.

Mounting Kit Contents

This manual provides installation instructions for server mount kit AB292A. This kit is intended for use with

the hp Integrity cx2600 server, and includes the following:

•ChassisTray(Base)

•TwoRackBrackets

• Cable Management Strain Relief Bar

• Mounting Hardware (screws, washers, and nuts)

HP Server Mount Kit for 19 in. 2-Post Rack Installation Instructions

Mounting Options

Chapter 1

Mounting Options

The server chassis can be mounted with the chassis front at the rack columns, or with the chassis centered

between the rack columns. The front-mount option facilitates alignment of the chassis front panel with those

of other items in the rack. (The tray provides adequate support to prevent unbalancing the rack or stressing

the columns.) The center-mount option provides improved weight distribution for those installations where

columns are already stressed.

Figure 1-1 Mounting Options

The mounting holes in the chassis rack ears, together with the holes in the tray (base) and rack columns

(approximately 1/4-inch centers) allow adjustment of the server mounting position, up to the practical limits

of weight distribution. The server is supported in the tray (base) and held in position by eight screws

(provided).

pmntopt

Front Mount Center Mount

HP Server Mount Kit for 19 in. 2-Post Rack Installation Instructions

Mounting the Server with Chassis Front Aligned with Rack Posts

Chapter 1 5

Mounting the Server with Chassis Front Aligned with Rack Posts

Figure 1-2 Front Mounting in a 2-Column Rack

Mounting Kit

Before mounting your server in a 2-column rack, inspect the mounting kit hardware. Review the installation

procedure and determine which screws will be required. (Alternate screws are provided due to the variations

in rack column mounting threads.) Verify that all needed parts are available. (A mounting kit parts list is

provided at the rear of this manual.)

Installation Procedure – Front Mount

Front-mount a server in a 2-column rack as follows:

Step 1. Install the tray (base) to the back of the rack columns, at the desired mounting position. Attach the

tray to the rack columns with T25 10-32 or 12-24 panhead screws, lockwashers, and #12

flatwashers.

2pfrtmnt1

HP Server Mount Kit for 19 in. 2-Post Rack Installation Instructions

Mounting the Server with Chassis Front Aligned with Rack Posts

Chapter 1

Figure 1-3Attach Kit Hardware to Rack Columns – Front Mount

Step 2. Install the 10-32 nut clips on the tray (base) where the bracket mounting screws will be installed.

Step 3. From the front of the rack, slide the server chassis onto the tray (base), with the chassis rack ears

against the rack columns. Attach the rack ears to the columns with T25 10-32 or 12-24 panhead

screws, lockwashers, and #12 flatwashers.

Figure 1-4Attach Server Rack Ears to Rack Columns – Front Mount

Step 4. Loosely attach the chassis brackets to each side of the server chassis with T15 screws and plated

flatwashers. Attach the rack brackets to the tray (base) with T25 10-32 screws. Then tighten all

screws.

Step 5. Attach the cable management strain relief bar to the brackets with T25 10-32 screws. (See

Figure 1-3.)

2pfrthrd

T25 10-32 or

12-24 Screws

Nut Clips

Bracket

(View from Rear)

Cable Management Bar

T25 10-32 Screws

Nut Clips

Tray

2pfrtmnt2 (View from Front)

T25 10-32 or

12-24 Screws Tray

Rack Ear

T15 Screws

Bracket

HP Server Mount Kit for 19 in. 2-Post Rack Installation Instructions

Mounting the Server with Chassis Centered Between Rack Posts

Chapter 1 7

Mounting the Server with Chassis Centered Between Rack Posts

Figure 1-5 Center Mounting in a 2-Column Rack

Mounting Kit

Before mounting your server in a 2-column rack, inspect the mounting kit hardware. Review the installation

procedure and determine which screws will be required. (Alternate screws are provided due to the variations

in rack column mounting threads.) Verify that all needed parts are available. (A mounting kit parts list is

provided at the rear of this manual.)

Installation Procedure – Center Mount

Center-mount a server in a 2-column rack as follows:

Step 1. Install the tray (base) to the front of the rack columns, at the desired mounting position. Attach the

tray to the rack columns with T25 10-32 or 12-24 panhead screws, lockwashers, and #12

flatwashers.

2pcntmnt1

HP Server Mount Kit for 19 in. 2-Post Rack Installation Instructions

Mounting the Server with Chassis Centered Between Rack Posts

Chapter 1

Figure 1-6Attach Kit Hardware to Rack Columns – Center Mount

Step 2. Install the 10-32 nut clips on the tray (base) where the chassis rack ear mounting screws will be

installed.

Step 3. From the front of the rack, slide the server chassis onto the tray (base), with the chassis rack ears

against the front of the tray. Attach the rack ears to the tray with T25 10-32 screws, lockwashers,

and #12 flatwashers.

Figure 1-7Attach Server Rack Ears to Server Tray – Center Mount

2pcnthrd

Tray

(View from Rear)

Bracket

T25 10-32 or

12-24 Screws Nut Clips

T25 10-32 or

12-24 Screws

Cable

Management

Bar

2pcntmnt2

Rack Ear

Bracket

Base

Rack Ear

(View from Front of Rack)

T15 Screws

T25 10-32

Screws

HP Server Mount Kit for 19 in. 2-Post Rack Installation Instructions

Mounting the Server with Chassis Centered Between Rack Posts

Chapter 1 9

Step 4. Loosely attach the chassis brackets to each side of the server chassis with T15 screws and plated

washers. Attach the rack brackets to the rack columns with T25 10-32 or 12-24 panhead screws,

lockwashers, and #12 flatwashers. Then tighten all screws.

Step 5. Attach the cable management strain relief bar to the brackets with T25 10-32 screws. (See

Figure 1-6.)

HP Server Mount Kit for 19 in. 2-Post Rack Installation Instructions

AB292A Rack Mount Kit

Chapter 1

AB292A Rack Mount Kit

The HP Server Mounting Kit, part number AB292A includes the items listed below.

* Due to variations in rack column mounting threads, alternate hardware is provided for installation

flexibility.

Table 1-1 Mounting Kit Parts List

Item Quantity HP Part Number

MFAB, base, rack 2-column 1 AB292-00001

Bracket, rack 2-column 2 AB292-00002

MFAB, cable management strain

relief bar

1 AB292-00011

Screw, T15, waferscrew, w/captive

lock washer, M4 x 7 mm 7.5 mm

8 A6474-00134

Screw, T25, 10-32,* 0.625”L,

panhead w/CC washer

16 2680-0323

Screw, slot/Phillips, 12-24 x 0.6”L,

panhead

8 2940-0503

Washer, flat, 4.3 mm ID, 12 mm

OD, 1 mm thick

8 3050-1244

Washer-lock, HLCL #12 0.225 ID,

0.377 OD, SS w/passivated finish

8 2190-0631

Nut clip, 10-32* 4 0590-2997

Washer, flat, #12, 0.25 ID, 0.562

OD, 0.062 thick, steel w/zink

plating

8 3050-0212

HP Server Mount Kit AB292A for

19-in. 2-Post Rack Installation

Instructions

1 AB292-96001

Otros manuales para Integrity cx2600

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accesorios de computadora de HP

HP XB4000 Manual de usuario

HP Xw6200 - Workstation - 2 GB RAM Manual de usuario

HP 98568A Manual de usuario

HP P5911A - Cordless Keyboard And Mouse Manual de usuario

HP HP Wired Keyboard + Mouse Manual de usuario

HP FQ481AA - Wireless Elite Desktop Keyboard Manual de usuario

HP QY449AA Instrucciones de uso

HP B1476 68020 Manual de usuario

HP Pavilion Slimline s3000 - Desktop PC Manual de usuario

HP x4500 Hoja de especificaciones

HP 5219URF Manual de instrucciones

HP MG-0133 Manual de usuario

HP Integrity cx2600 Manual de usuario

HP P2360AA #ABA Manual de usuario

HP MORFD3UO Manual de usuario

HP USB Media Docking Station Manual de usuario

HP HSA-D01K Manual de usuario

HP DHN0 Guía

HP Officejet 635 Manual de usuario

HP Comm Station Manual de usuario

HP Integrity cx2600 Manual de usuario

HP Z6500 Hoja de especificaciones

HP 463777-001 Manual

HP Xw4550 - Workstation - 2 GB RAM Manual de usuario

Manuales populares de Accesorios de computadora de otras marcas

Motorola

Motorola ATRIX Manual de usuario

Cherry

Cherry B.UNLIMITED 3.0 Manual de usuario

Logitech

Logitech IO2 Manual de usuario

ARM

ARM DSTREAM-ST Manual de usuario

Bartec

Bartec TC 7 Series Manual de usuario

Philips

Philips SPC3540 Manual de usuario

Logitech

Logitech mk220 Manual de usuario

SilverStone

SilverStone LC02 Manual de usuario

Flexispot

Flexispot ML2B Manual de usuario

Hamlet

Hamlet UNIVERSAL COVER 101 KBT2 Manual de usuario

Adam Equipment

Adam Equipment RS-485 Manual de usuario

Vivo

Vivo MOUNT-KB05-4DW Manual de usuario

Kvaser

Kvaser Memorator Professional Manual de usuario

DRC

DRC D-Imaging Manual de usuario

Sven

Sven Base 305 сombo Manual de usuario

Hama

Hama 108310 Manual de usuario

SpeechWare

SpeechWare FlexyMike FMK03 Manual de usuario

Sony

Sony Vaio VGP-FL10 Manual de usuario