Hoover FH55000 Instrucciones de funcionamiento

Service Instructions

Hoover PowerDash Pet- PowerDash Pet Complete

PowerDash Pet Model #: FH50710V, FH50700UPC, FH50700, FH50710CN, FH50750, FH50700PDI

GL, FH50700FDI, FH50700CDI, FH50702, FH50703CDI, FH50700V, FH50750V, FH50750PDI,

FH50703VCD, FH50704, FH50704V, FH50711CN, FH50711V, FH50751, FH50751V, FH50751PDI,

FH50751VPD, FH50704FDI, FH50704VFD, FH50701CDI, FH50740CDI.

PowerDash Pet Complete Model #: FH50704, FH50711CN, FH50751, FH50751PDI, FH50704FDI,

FH50701CDI, FH50740CDI, FH50704V, FH50711V, FH50751V, FH50751VPD, FH50704VFD,

FH50701VCD, FH50740VCD, FH55050PC, FH55010, FH55000, FH55050V, FH55010V, FH55000V

TO VIEW PARTS SCHEMATICS PLEASE VISIT “PARTS CATALOG” THROUGH THE DEALER

PORTAL HOME PAGE.

Troubleshooting

A. Unit Leaking

1. The clean and dirty tank are not placed properly or might be filled.

(1) Check to ensure all tanks are properly filled or empty (dirty water tank cannot be over the

max limit, to prevent leaking through the motor)

(2) Ensure the tanks are firmly placed into the unit and there are no gaps or looseness.

2. Dirty Water Tank Lid is not secure.

(1) Make sure there are no gaps in your dirty water tank. Also check that the lid of your tank

is properly fitted in.

3. Check tanks to determine if leaking occurs while installed or removed from unit.

Clean Tank does have an amount of residual water when removed from tank resoivour.

Check tank caps to ensure seals are in place and sealing tanks.

4. Remind the customer to allow residual water to make its way back into the dirty water tank

after they are done cleaning. This is to prevent leaking once its stored.

B. Unit Won’t Dispense

1. Clean Water Tank is Empty and the handle is loose

(1) Check to ensure that the Clean Water Tank and solution tank is properly filled and

properly fitted into the unit

(2) The unit will not dispense if the handle is not properly installed

2. Unit may need to be flushed.

(1) Add warm tap water to both the clean water tank and the solution tank. Make sure both

tanks are seated firmly, turn the unit on, and recline the handle. Push the unit forward

continuously about 3-4 times or until water comes out of the bottom. Power ON again.

3. Unit may need to be reset.

To reset the PowerDash, unplug it from the wall. Remove the nozzle cover and take out the

brushes. Now, replace the nozzle cover, plug the unit back in, and cycle the power on and off

4 times. Replace the brushes and test to see if the reset worked.

C. Accessory Hose/Tool Won’t Dispense (ONLY for PowerDash Pet Complete)

1. Check to ensure that Clean Water Tank and Solution Tanks are full.

2. Ensure there are no clogs in the hose end.

(1) Check both ends of the hose and clean any clogs or debirs you may encunter. Make sure

they also clean the accesory tools.

(2) Insert a small object into the hose solution port to ensure is not clogged.

3. There may be air trapped in the hose and pump. In this case, you will need to prime the pump

by lowering the hose to the floor and holding the trigger for up to one minute.

D. Unit Won’t Pick Up or Has Poor Suction

1. Dirty Water Tank is Full (Float Engaged), the float can also be tripped if the unit is lifted

from the floor while is ON.

(1) Turn off the unit and empty the Dirty Water Tank. They will notice the float goes back to

its original position.

2. The Nozzle is not secure

(1) Pull up on the latch and pull forward to remove the nozzle cover. Check the nozzle

opening for any clogs or blockages. To replace the nozzle cover, line up the two tabs on

the base as well as the tabs close to the opening. Push down and backward until the latch

clicks into place.

(2) On the PowerDash Pet Complete there a quick access to the brush roll for cleanup. See

picture 2 below.

3. The debris filter is dirty

(1) Remove the debris filter, located under the Dirty Water Tank, wipe it clean.

4. There is a clog in the tool at the end of the hose.

(1) Remove the tool and clear out any debris.

5. The Unit needs to be reset

(1) To reset the PowerDash, unplug it from the wall. Remove the nozzle cover and take out

the brushes. Now, replace the nozzle cover, plug the unit back in, and cycle the power on

and off 4 times. Replace the brushes and test to see if the reset worked.

E. Brushroll Not Spinning

1. Make sure the unit is NOT in the upright position

(1) If the unit is in the upright position, the brushroll won’t spin. Tilt the unit backwards.

2. The brushroll stall protection has been activated. This happens when the brushroll gets

jammed or clogged.

(1) Turn the unit off and back ON again.

(2) Make sure to remove your brushroll and clean any tangled hair or debris that could be

causing the stall. Temember to clean the notches inside the nozzle too.

See below

3. The belt might be broken. (You may experience a burning smell, or a high pitch sound)

(1) Remove the bottom plate of the unit and remove the brushroll.

(2) Place the new belt on the motor shaft

(3) Position the non-belt side of the roll into the notch it belong to.

(4) Carefully stretch the belt to position the other en cap into the notch

(5) Replace the belt cover and secure the 6 screws to the plate.

See below

F. Unit Not Turning ON

(1) Make sure their unit is firmly plugged into a working outlet.

(2) Check there are no outages or issues with the fuse at the customer’s home

(3) The thermal protector might have activated. The unit does this to prevent damage from

overheating.

(a) Unplug the unit from the outlet.

(b) Clean the dirty and clean water tanks

(d) Allow the unit to cool down for up to 30 minutes. Then plug back ON

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Aspiradora de Hoover

Hoover

Hoover S3410 Manual de usuario

Hoover

Hoover POWER SCRUB Manual de usuario

Hoover

Hoover 5014 pets Manual de usuario

Hoover

Hoover Convertible U4039 Manual de usuario

Hoover

Hoover HURRICANE HU71HU02 Manual de usuario

Hoover

Hoover S3670 - WindTunnel Bagged Canister Vacuum... Guía de configuración rápida

Hoover

Hoover CONVERTIBLE U4057 Manual de usuario

Hoover

Hoover S3592 Manual de usuario

Hoover

Hoover TurboPower WindTunnel Series Manual de usuario

Hoover

Hoover SmartWash Pet Complete Manual de usuario

Hoover

Hoover FloorMate Deluxe Manual de usuario

Hoover

Hoover Carpet Cleaner Guía del usuario

Hoover

Hoover Spirit S3503 Manual de usuario

Hoover

Hoover HHWD14 Guía de instalación

Hoover

Hoover SteamVac LS Manual de usuario

Hoover

Hoover Sensory Manual de usuario

Hoover

Hoover Breathe Easy Manual de usuario

Hoover

Hoover S3612 - Household Vacuum Cleaners Manual de usuario

Hoover

Hoover U5180 Manual de usuario

Hoover

Hoover UH20020RM Manual de usuario

Hoover

Hoover Presto 2-in-1 Manual de usuario

Hoover

Hoover Platinum Collection Manual de usuario

Hoover

Hoover 3010 PERFORMER Manual de usuario

Hoover

Hoover UH70035B - WindTunnel Cyclonic Upright... Manual de usuario

Manuales populares de Aspiradora de otras marcas

Bissell

Bissell LittleGreen Proheat 1425 Series Manual de usuario

Panasonic

Panasonic MC-YL637S147-AE Manual de usuario

NEFF

NEFF N17XH10 0 Series Manual de usuario

LG A9 Series Manual de usuario

Oreck

Oreck Cordless Captura BK51700 Series Manual de usuario

Kogan

Kogan KAVACROBVWA Manual de usuario

Kränzle

Kränzle VENTOS 50 ID Guía del usuario

EVVO

EVVO Ai35 Manual de usuario

DeWalt

DeWalt DWH200D Manual de usuario

Pontec

Pontec Pondomatic Vacuum Cleaner Manual de usuario

Cleanmaxx

Cleanmaxx PC-P007E Manual de usuario

Exido

Exido 240-114 Manual de usuario

RIDGID

RIDGID WD1685AU0 Manual de usuario

Ezviz

Ezviz RE4P Manual de usuario

STG global

STG global TANVAC HDV3000 Manual de usuario

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Manual de usuario

Factory

Factory M3340 Manual de usuario

Shop-Vac

Shop-Vac VN92 SERIES Manual de usuario