Honeywell TH8320ZW Manual de usuario

TH8320ZW

Touch-screen Thermostat

Installation

Guide

® U.S. Registered Trademark.

US Patent No. 6,574,581, 6,975,958, 7,114,554,

7,34 6,467, 7,636,604, 7,693,582, 7,78 8 , 9 3 6 ,

7,845,576, and other patents pending.

System Types

• Gas,oil,orelectricheatwithair

conditioning

• Warmair,hotwater,high

efficiency furnaces, heat

pumps, steam, gravity

• Heatonly—includingpowertoopen

and close zone valves (Series 20), and

normally open zone valves

• Heatonlywithfan

• Coolonly

• 750mVheatingsystems

This manual covers the TH8320ZW.

This thermostat contains a Lithium battery which may contain Perchlorate material.

PerchlorateMaterial—specialhandlingmayapply.

See www.dtsc.ca.gov/hazardouswaste/perchlorate

Need Help?

For assistance with this product please visit http://customer.honeywell.com

or call Honeywell Customer Care toll-free at 1-800-468-1502

Installation Guide

69-2486—07

M29481

Wallplate installation

1. Separate wallplate from thermostat.

2. Mount wallplate as shown below.

MERCURY NOTICE

If this product is replacing a control that contains mercury in a sealed tube, do not

place the old control in the trash. Contact your local waste management authority for

instructions regarding recycling and proper disposal.

Grasptopandbottomofwallplate

and pull to remove from thermostat.

CAUTION: ELECTRICAL HAZARD

Can cause electrical shock or equipment damage. Disconnect power before beginning

installation.

Drill 3/16” holes for drywall.

Drill 7/32” holes for plaster.

Wallanchors

Wirehole Mounting screws

Must be installed by a trained, experienced technician

• Readtheseinstructionscarefully.Failuretofollowtheseinstructions

can damage the product or cause a hazardous condition.

M29480

TH8320ZW

369-2486—07

M32429

Power Requirements

Wiring

Connect the common side of the

transformer to “C” terminal. This

connection is mandatory.

Remove tab.

The thermostat is shipped from the factory

with the coin cell installed. To keep the bat-

tery from discharging during shipment and

storage, the thermostat is shipped with a

plastic tab inserted in the battery holder.

This tab must be removed during installa-

tion. Simply pull the plastic tab out of the

battery tray. Make sure that the battery tray

is fully inserted into the thermostat.

Push excess wire back into the wall opening. Plug

wall opening with non-flammable insulation.

Remove factory-installed jumper only

for two-transformer systems.

M32431

M32430B

HEAT PUMP

CONVENTIONAL

M32428A

HEAT PUMP

CONVENTIONAL

Installation Guide

69-2486—07

Wiring

See [notes] below

[1] Power supply. Provide disconnect means and overload protection as required.

 [3] Connectionto24VACcommonatthetransformerisrequired.

 [9] See"OptionalTHP9045WiringModule"on page 14 for more details.

Terminal Designations

Conventional Terminal Letters:

R Heating power. Connect to secondary

side of heating system transformer.

Rc Cooling power. Connect to secondary

side of cooling system transformer.

C Common wire from secondary side of

cooling transformer (if 2 transformers).

W 1st stage heat relay.

W2 2nd stage heat relay

Y 1st stage compressor contactor.

Y2 2nd stage compressor contactor.

G Fan relay.

K OptionalTHP9045WiringModule

Terminal [9]

Heat Pump Terminal Letters:

R Heating power. Connect to secondary

side of heating system transformer.

Rc Cooling power. Connect to secondary

side of cooling system transformer.

C Common wire from secondary side of

cooling system transformer.

Y 1st stage compressor contactor.

Y2 2nd stage compressor contactor.

Aux Auxiliary heat relay.

G Fan relay.

E Emergency heat relay.

L Heat pump reset (powered continu-

ously when System is set to Em Heat;

system monitor when set to Heat,

Cool or Off).

O/B Changeover valve for heat pumps.

K OptionalTHP9045WiringModule

Terminal [9]

1H/1C System (1 transformer)

Rc Power [1]

R [R+Rc joined by jumper]

W Heat relay

Y Compressor contactor

G Fan relay

C 24VACcommon[3]

K OptionalTHP9045WiringModule

Terminal [9]

Heat Only System

Rc Power [1]

R [R+Rc joined by jumper]

W Heat relay

C 24VACcommon[3]

Heat Only System (Series 20)

Rc [R+Rc joined by jumper]

R Series 20 valve terminal “R” [1]

W Series 20 valve terminal “B”

Y Series20valveterminal“W”

C 24VACcommon[3]

2H/2C System (1 transformer)

Y2 Cool relay 2

W2 Heat relay 2

Rc Power [1]

R [R+Rc joined by jumper]

W Heat relay 1

Y Cool relay 1

G Fan relay

C 24VACcommon[3]

K OptionalTHP9045WiringModule

Terminal [9]

Wiring guide—conventional systems

TH8320ZW

569-2486—07

1H/1C Heat Pump (no auxiliary heat)

Rc Power [1]

R [R+Rc joined by jumper]

O/B Changeover valve [5]

Y Compressor relay

G Fan relay

C 24VACcommon[3]

K OptionalTHP9045WiringModule

Terminal [9]

2H/1C Heat Pump (with auxiliary heat)

L Equipment monitor [6, 7]

E Emergency heat relay [8]

Aux Auxiliary heat relay (Heat 2) [8]

Rc Power [1]

R [R+Rc joined by jumper]

O/B Changeover valve [5]

Y Compressor relay

G Fan relay

C 24VACcommon[3]

K OptionalTHP9045WiringModule

Terminal [9]

2H/2C Heat Pump (no auxiliary heat)

Y2 Compressor 2 relay

Rc Power [1]

R [R+Rc joined by jumper]

O/B Changeover valve [5]

Y Compressor 1 relay

G Fan relay

C 24VACcommon[3]

K OptionalTHP9045WiringModule

Terminal [9]

1H/1C System (2 transformers)

Rc Power (cooling transformer) [1, 2]

R Power (heating transformer) [1, 2]

W Heat relay

Y Compressor contactor

G Fan relay

C 24VACcommon[3,4]

K OptionalTHP9045WiringModule

Terminal [9]

Heat Only System With Fan

Rc Power [1]

R [R+Rc joined by jumper]

W Heat relay

G Fan relay

C 24VACcommon[3]

Cool Only System

Rc Power [1]

R [R+Rc joined by jumper]

Y Compressor contactor

G Fan relay

C 24VACcommon[3]

K OptionalTHP9045WiringModule

Terminal [9]

2H/2C System (2 transformers)

Y2 Cool relay 2

W2 Heat relay 2

Rc Power (cooling transformer) [1, 2]

R Power (heating transformer) [1, 2]

W Heat relay 1

Y Cool relay 1

G Fan relay

C 24VACcommon[3,4]

K OptionalTHP9045WiringModule

Terminal [9]

Wiring guide—heat pump systems

Wiring

See [notes] below

[1] Power supply. Provide disconnect means and overload protection as required.

[2] Remove jumper for 2 transformer systems.

 [3] Connectionto24VACcommonatthetransformerisrequired.

[4] Common connection must come from cooling transformer.

[5] O/B set to control as either Oor Bin installer setup.

[6] If Lterminalisused,24VACcommon(terminalC)must be connected.

[7] Heat pump reset (powered continuously when thermostat is set to Em. Heat; system monitor

when set to Heat, Cool, or Off).

[8] Install field jumper between Aux and Eterminals if there is no emergency heat relay.

 [9] See"OptionalTHP9045WiringModule"on page 14 for more details.

Installation Guide

69-2486—07

SCHEDHOLD

TUE

FA N

AUTO

Inside

6:00

SYSTEM

HEAT

DONE

0120

DONE CANCEL

6:00

SYSTEM

HEAT

M32417

DONE

TUE

2006

DONE

TUE

1:00

M29485

Align pins on back of thermostat

with slots in wallplate, then push

gently until thermostat snaps into

place.

Mount thermostat

Set date and time

Press st

to set time

Press st

to set date

Press st

to set month

Press st

to set year

Installer setup

Press DONE to save changes. Press DONE to save and exit.

1. Press SYSTEM.2. Press and hold

these two buttons

until the display

changes.

3. Change settings

as required (see

pages 7-9).

M32435

TH8320ZW

769-2486—07

DONE

0120

DONE

0120

M32427

Installer setup

SettingFunction

Press DONE to exit & save settings.

Press st to

select function

Press st to

change setting

Setup functions Settings & Options (factory default in bold)

0120 Year

(rst two digits)

20 (2000-2078)

21 (2101-2178)

0130 Year

(second two digits)

10 (2010)

[Other options: 00-99]

0140 Month 6[Other options: 1-12]

0150 Date 15 [Other options: 1-31]

0160 Schedule format 0 Nonprogrammable

4 Programmable

0165 Restore Energy

Saving Schedule

0 No

1 Yes

0170 System type 1 1 heat/1 cool conventional

2 1 heat/1 cool heat pump (no aux. heat)

3 Heat only (2-wire systems)

4 Heat only with fan

5 Hot water Series 20 system (power to open & close zone

valves/normally open zone valves)

6 Cool only

7 2 heat/1 cool heat pump (with aux. heat)

8 2 heat/2 cool multistage conventional

9 2 heat/1 cool multistage conventional

10 1 heat/2 cool multistage conventional

11 2 heat/2 cool heat pump (no aux. heat)

12 3 heat/2 cool heat pump (with aux. heat)

0180 Fan control

(heating)

0 Gas/Oil heat (equipment controls heating fan)

1Electric furnace (thermostat controls heating fan)

0190 Changeover valve

(O/B terminal)

0 O terminal controls valve in cooling

1 B terminal controls valve in heating

0220 1st stage compressor

cycle rate

3Recommended for most compressors

[Other options: 1, 2, 4, 5 or 6 CPH]

0230 2nd stage compressor

cycle rate

3 Recommended for most compressors

[Other options: 1, 2, 4, 5 or 6 CPH]

0240 1st stage heat cycle

rate (CPH = cycles

per hour)

5 Gas or oil furnaces of less than 90% efficiency

1 Steam or gravity systems

3 Hot water systems & furnaces of 90%+ efficiency

9 Electric furnaces

[Other options: 2, 4, 6, 7, 8, 10, 11, 12 CPH]

Continued on next page

Installation Guide

69-2486—07

Setup functions Settings & Options (factory default in bold)

0250 2nd stage heat

cycle rate (CPH)

9 Electric furnaces

1Steam or gravity systems

3Hot water systems & furnaces of 90%+ efficiency

5Gasoroilfurnacesoflessthan90%efficiency

[Other options: 2, 4, 6, 7, 8, 10, 11, 12 CPH]

0260 3rd stage heat cycle

rate (CPH)

9 Electric furnaces

1Steam or gravity systems

3Hot water systems & furnaces of 90%+ efficiency

5Gasoroilfurnacesoflessthan90%efficiency

[Other options: 2, 4, 6, 7, 8, 10, 11, 12 CPH]

0270 Emergency heat

cycle rate (CPH)

9 Electric emergency heat

1Steam or gravity systems

3Hot water systems & furnaces of 90%+ efficiency

5Gasoroilfurnacesoflessthan90%efficiency

[Other options: 2, 4, 6, 7, 8, 10, 11, 12 CPH]

0280 Continuous

Backlight

0 Backlight on for approx. 45 seconds after keypress

1Backlight always on low intensity, full bright after keypress

(requires24VACconnection)

0300 Manual/Auto

changeover

0 Manual changeover (Heat/Cool/Off)

1 Automatic changeover (Heat/Cool/Auto/Off)

0310 Auto changeover

deadband

3 Heat/cool temperature 3°F apart (1.5°C)

[Other options: 2-9 (2°F to 9°F/1°C to 5°C)])

0320 Temperature

display

0 Fahrenheit

1Celsius

0330 Daylight savings 1 Auto-change to daylight savings time (through 2007, and for

areas that do not use the new 2008 DST calendar)

0Daylight savings time is turned off

0500 Furnace lter

change reminder

0 Off

1 10-day run time (about 1 month)

2 30-day run time (about 3 months)

3 60-day run time (about 6 months)

4 90-day run time (about 9 months)

5 120-day run time (about 1 year)

6 180-day run time (about 1.5 years)

7 270-day run time (about 2 years)

8 365-day run time (about 3 years)

9 30 calendar days

10 60 calendar days

11 90 calendar days

12 120 calendar days

13 180 calendar days

14 365 calendar days

0502 Furnace lter

for Run time

0 Counts both heat and cool

1 Counts cool only

0520 UV Lamp

Replacement

Reminder

0 Disabled

1 365 days

2 730 days

0530 Adaptive Intelligent

Recovery™

1 On

0 Off

Installer setup

Continued on next page

TH8320ZW

969-2486—07

Setup functions Settings & Options (factory default in bold)

0540 Program periods 4 4 program periods (Wake, Leave, Return, Sleep)

2 2programperiods(Wake,Sleep)

0580 Compressor

protection

5 5 minute compressor off time

[Other options: 0, 1, 2, 3 or 4-minute off time]

0600 Heat temperature

range stop

90 Max. heat temperature setting is 90°F (32°C)

[Other options: 40-89°F (4°C to 32°C)]

0610 Cool temperature

range stop

50 Min. cool temperature setting is 50°F (10°C)

[Other options: 51-99°F (11°C to 37°C)]

0615 Energy Saving

Heat Setpoint

65 65°F (18.5°C)

40-90°F (4.5°C to 32°C)

0616 Energy Saving

Cooling Setpoint

78 78°F (25.5°C)

50-99°F (10°C to 37°C)

0640 Clock format 12 12-hour time (i.e., “3:30 pm”)

24 24-hour time (i.e., “15:30”)

0650 Extended fan

timer (heat)

0 Off

90 Fan runs for 90 seconds after call for heat ends

[Other options: 30, 60, 120]

0660 Extended fan

timer (cool)

0 Off

90 Fan runs for 90 seconds after call for cooling ends

[Other options: 30, 60, 120]

0670 Keypad lock 0 Keypad unlocked (fully functional)

1 Partially locked (access to temperature settings only)

2 Fully locked

0680 Heat temperature

control

2 Standard temperature control (recommended)

1 Choose if room is warmer than set temperature

3 Choose if room does not reach set temperature

0690 Cool temperature

control

2 Standard temperature control (recommended)

1 Choose if room is cooler than set temperature

3 Choose if room does not reach set temperature

0700 Temperature

display offset

0 Thermostat displays actual room temperature

[Other options: -3, -2, -1, 1, 2, 3°F offset (-1.5°C to 1.5°C)]

0710 Reset 0 No reset

1 Resetinstalleroptions,theZ-WaveRadiomodule,&program-

ming schedule to factory default (only date and time settings

are retained)

rf10 Z-Wave Network

Connection

0 Remove

1 Add

rf20 Z-Wave Node

Connection

0 Idle

1 Send Node

Installer setup

Installation Guide

69-2486—07

DONE

0120

DONE

TEST

M29488

During installer setup, press t

repeatedly until “Test” appears.

Test

number

System

status

Press tto

select test

Press tto

change status

Press DONE to terminate testing.

1 Cooling system 0 Compressor and fan turn off

1 Compressor and fan turn on

2 Second stage compressor turns on

2 Fan system 0 Fan turns off

1 Fan turns on

3 Heating system 0 Heat and fan turn off

1 Heat turns on (fan on if Function 0170 is set for heat pump,

or if Function 0180 is set to “1”)

2 Second stage heat turns on

4 Emergency

heating system

0 Em Heat and fan turn off

1 Em Heat and fan turn on

2 Second stage heat turns on (Auxiliary heat)

System test System status

CAUTION: EQUIPMENT DAMAGE HAZARD. Compressor protection is bypassed dur-

ing testing. To prevent equipment damage, avoid cycling the compressor quickly.

Installer system test

Z-Wave enrollment

1. TojoinaZ-Wave

network, set the

Z-Wavecontroller

to INCLUDE mode.

2. Select 1 to add

thermostat to

Z-Wavenetwork.

DONE

M32423A

TheTH8320ZWispoweredbyZ-Wave

technology so it is compatible with

Z-Waveenableddevicesfromother

manufacturers.

Otros manuales para TH8320ZW

Tabla de contenidos

Otros manuales de Termostato de Honeywell

Honeywell

Honeywell VisionPRO TH8000 Series Manual de usuario

Honeywell

Honeywell RTH2300B1038/E1 Manual de usuario

Honeywell

Honeywell Q539A Manual de usuario

Honeywell

Honeywell TH401 Manual de usuario

Honeywell

Honeywell CHRONOTHERM III T8611G Manual de usuario

Honeywell

Honeywell Chronotherm III T8602A Manual de usuario

Honeywell

Honeywell T7200 Manual de usuario

Honeywell

Honeywell Tradeline T8024D Manual de usuario

Honeywell

Honeywell T8112 Manual de usuario

Honeywell

Honeywell INTELLIGUARD 9000 Manual de usuario

Honeywell

Honeywell VisionPRO Wi-Fi TH8320WF Manual de usuario

Honeywell

Honeywell T8112D Guía de inicio rápido

Honeywell

Honeywell Chronotherm III Manual de usuario

Honeywell

Honeywell W884B Manual de usuario

Honeywell

Honeywell ultrastat CT1700A Manual de usuario

Honeywell

Honeywell CT410A Manual de usuario

Honeywell

Honeywell T6380 Manual de operación

Honeywell

Honeywell RTH3100C Manual de usuario

Honeywell

Honeywell DG115EZIAQ - TrueIAQ Digital IAQ Control Manual de usuario

Honeywell

Honeywell CT50A Manual de usuario

Honeywell

Honeywell Digital Round T8775A Manual de usuario

Honeywell

Honeywell FocusPRO TH6320WF02 Manual de usuario

Honeywell

Honeywell DTS92A Manual de usuario

Honeywell

Honeywell T8000C Manual de usuario

Manuales populares de Termostato de otras marcas

EWELLY

EWELLY EW-181 Manual de usuario

Prolon

Prolon T1100 Instrucciones de instalación

Computherm

Computherm Q20 Manual de usuario

Heatmiser

Heatmiser neoStat Manual de usuario

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario

Saswell

Saswell SAS920XWHB-7-S-RF Guía

Aircalo

Aircalo TFP1-ET85P2 Manual de usuario

Carrier

Carrier DEBONAIR 33CS Manual de usuario

Lennox

Lennox iHarmony Zone Thermostat Instrucciones de montaje

Gemtech

Gemtech GT7000 Manual de instrucciones

Rollei

Rollei Smartes 45000 Manual de usuario

Sinope

Sinope TH1300RF Manual de usuario

NuTone

NuTone NTBZ48 Instrucciones de funcionamiento originales

Stelpro

Stelpro MAESTRO ASMT402AD Manual de usuario

Aube Technologies

Aube Technologies TH305 Manual de usuario

Powtier Controls

Powtier Controls 505MST Manual de usuario

Kanmor

Kanmor Zone Control 369e Manual de usuario