Honeywell T7200D Manual de usuario

APPLICATION

The T7200D,E Thermostats provide electronic control of

24 Vac commercial single-zone heating, ventilating and air

conditioning (HVAC) equipment. The T7200 is field

configurable for automatic or manual changeover between

heating and cooling. The system and fan selections are

made by keyboard entry. All T7200 Thermostats require a

common wire to supply power.

RECYCLING NOTICE

If this control is replacing a control that contains

mercury in a sealed tube, do

not

place your old

control in the trash.

Contact your local waste management authority for

instructions regarding recycling and the proper

disposal of the old thermostat.

X-XX UL

INSTALLATION INSTRUCTIONS

® U.S. Registered Trademark

T7200D,E Series 2000 Commercial

Microelectronic Thermostats

INSTALLATION

When Installing this Product…

1. Read these instructions carefully. Failure to follow

the instructions can damage the product or cause a

hazardous condition.

2. Check the ratings given in the instructions and on

the product to make sure the product is suitable for

your application.

3. Installer must be a trained, experienced service

technician.

4. After completing installation, use these instructions

to check out the product operation.

Location

Install the thermostat about 5 ft (1.5m) above the floor in

an area with good air circulation at average temperature.

See Fig. 1.

5 FEET

(1.5 METERS)

YES

M4823A

Fig. 1. Typical location of thermostat.

62-0128-2

62-0128—2 2

T7200D,E SERIES 2000 COMMERCIAL MICROELECTRONIC THERMOSTATS

Do not install the thermostat where it can be affected by:

—drafts, or dead spots behind doors and in corners.

—hot or cold air from ducts.

—radiant heat from sun or appliances.

—concealed pipes and chimneys.

—unheated (uncooled) areas such as an outside wall

behind the thermostat.

Mounting Wallplate

The wallplate mounts horizontally on the wall or on a

2 in. x 4 in. wiring box. Position the wallplate horizontally

on the wall or on a 2 in. x 4 in. wiring box.

1. Position and level the wallplate (for appearance

only). The thermostat functions properly even when

not level.

2. Use a pencil to mark the mounting holes. See Fig. 2.

3. Remove the wallplate from the wall and drill two

3/16 inch (4.8 mm) holes in the wall (if drywall) as

marked. For firmer material such as plaster or wood,

drill two 7/32 inch (5.5 mm) holes. Gently tap

anchors (provided) into the drilled holes until flush

with the wall.

4. Position the wallplate over the holes, pulling wires

through the wiring opening.

5. Loosely insert the mounting screws into the holes.

6. Tighten mounting screws.

CAUTION

Electrical Shock Hazard.

Power source can cause electrical shock.

Disconnect power before wiring to prevent

electrical shock or equipment damage.

1. Loosen the terminal screws on the wallplate and

connect the system wires. See Fig. 3.

IMPORTANT

Use 18-gauge, solid-conductor color-coded

thermostat cable for proper wiring. If using

18-gauge stranded wire, do not use more than

ten wires. Do not use larger than 18-gauge wire.

2. Securely tighten each terminal screw.

3. Push excess wire back into the hole.

4. Plug the hole with nonflammable insulation to

prevent drafts from affecting the thermostat.

Fig. 2. Mounting the wallplate.

WIRING WALLPLATE

All wiring must comply with local electrical codes and

ordinances. Follow equipment manufacturer wiring

instructions when available. Refer to Fig. 4 and 5 for

typical hookups. A letter code is located near each

terminal for identification.

WIRES

THROUGH WALL

WALL

ANCHORS

(2)

M10237

LEDS

MOUNTING

HOLES

MOUNTING

SCREWS

Fig. 3. Proper wiring technique.

M4826

FOR WRAPAROUND

INSERTION STRIP

7/16 IN. (11 MM).

FOR STRAIGHT

INSERTION STRIP

5/16 IN. (8 MM).

Fig. 4. Typical hookup of T7200D in single-stage

heating and cooling conventional system.

(HOT)

POWER SUPPLY. PROVIDE DISCONNECT MEANS AND

OVERLOAD PROTECTION AS REQUIRED.

HEATING

RELAY OR

VALVE COIL

JUMPER RC AND RH FOR SINGLE TRANSFORMER SYSTEMS.

M4942A

RCRHXY1GW1

THERMOSTAT

COMPRESSOR

CONTACTOR

FAN

RELAY

62-0128—2

T7200D,E SERIES 2000 COMMERCIAL MICROELECTRONIC THERMOSTATS

M4824A

PRESS LOWER EDGE OF CASE TO LATCH.

ENGAGE TABS AT TOP OF THERMOSTAT AND SUBBASE OR WALLPLATE.

Fig. 5. Typical hookup of T7200E in single-stage heat

pump system.

Mounting Thermostat on Wallplate

The thermostat mounts on the wallplate after it is installed.

1. Engage the tabs at the top of the thermostat and

wallplate. See Fig. 6.

2. Press the lower edge of the case to latch.

NOTE: To remove the thermostat from the wall, first pull

out at the bottom of the thermostat; then remove

the top.

SETTINGS

Using Thermostat Keys

The thermostat keys are used to:

•set current time and day,

•program times and setpoints for heating and cooling,

•override the program temperatures,

•display present setting,

•set system and fan operation,

•configure Installer Setup,

•check Installer System Test.

See Fig. 7 for thermostat key information.

Set Program Set Temperature Change

Time/Temp

Occupied

Temp

Unoccupied

Start Time Day

System Fan

Copy

Occupied

Start Time

Run

Program

Temporary

Occupied

Continuous

Unoccupied

Set Current

Day/Time Clear

Start Time

Unoccupied

Temp

Heat/Cool

Settings

Auto

System Fan

Mon

Room

Occupied

Heat

M10233A

SET OVERRIDE

TEMPERATURE

OFFSET AND

ACTIVATE

TEMPORARY

OVERRIDE

ENTER HOLD MODE SET CURRENT

DAY AND TIME

CLEAR PROGRAM PERIOD COPY ONE

PROGRAMMED DAY

TO ANOTHER DAY

SELECT FAN

OPERATION

SELECT

SYSTEM

OPERATION

CHANGE BETWEEN HEATING

AND COOLING SETPOINTS

AND SCROLLS BACKWARDS

THROUGH INSTALLER SETUP

NUMBERS AND SYSTEM TEST

DECREASE

TEMPERATURE

OR TIME SETTING

INCREASE

TEMPERATURE

OR TIME SETTING

SET UNOCCUPIED TEMPERATURE

SETPOINTS AND SCROLLS

THROUGH INSTALLER SETUP

AND SYSTEM TEST

SET OCCUPIED

TEMPERATURE

SETPOINTS

SET CURRENT DAY OR

PROGRAM DAY

ENTER UNOCCUPIED

PROGRAM MODE

ENTER OCCUPIED

PROGRAM MODE

RETURNS TO

NORMAL

OPERATIONS

Fig. 6. Mounting thermostat on wallplate.

Fig. 7. Thermostat key locations and descriptions.

(HOT)

POWER SUPPLY. PROVIDE DISCONNECT MEANS AND

OVERLOAD PROTECTION AS REQUIRED.

COOL

CHANGEOVER

VALVE

M4943A

RXYGO

THERMOSTAT

COMPRESSOR

CONTACTOR

FAN

RELAY

62-0128—2 4

T7200D,E SERIES 2000 COMMERCIAL MICROELECTRONIC THERMOSTATS

Fig. 9. Installer Setup number and setting display.

Installer Setup numbers are listed in Table 2.

CAUTION

Possible Equipment Damage.

Fan must be running when system is

operating.

Configure heat pump and electric heat systems in

Installer Setup 2 to prevent equipment damage

caused by the system running without the fan.

IMPORTANT

Only configurable numbers are shown on the

device. Example: If the thermostat does not have

a system key, Installer Setup Number 12 will not

be displayed. Review Table 2 factory settings

and mark any desired changes in the Actual

Setting column. When Installer Setup is com-

plete, review the settings to confirm that they

match the system.

Heat

Auto

System Fan

Off Auto

Mon

Wait

Room

Remote

%Humid

Auto

Sav

Comm Cool Duct

Only

Recovery

Med

Cool

TueWedThuFriSatSun

Occupied 12 Override

M4916

Aux Ht

Em Ht

Set Program

Set Day/Time

Start Time Temporary Setting Enrg

Em Heat

Setting System and Fan (select models)

The system default setting is Heat. The fan default is set

so the fan operates continuously in the Occupied and

Recovery modes and with the heating or cooling equip-

ment in the Unoccupied mode. Use the System and Fan

keys to change the settings.

The system settings are:

Heat: Thermostat controls the heating.

Off: Both the heating and cooling are off.

Cool: Thermostat controls the cooling.

Auto: Thermostat automatically changes between

heating and cooling operation depending on the

indoor temperature.

The fan settings are:

On: Fan operates continuously.

Auto: Equipment controls the fan in the Unoccupied

mode. The Intelligent Fan™ operation (Installer

Setup number 17) offers three choices for the fan

operation in Occupied mode:

—fan turns on only when there is a call for heating

or cooling,

—fan operates continuously in Occupied mode,

—fan is on continuously in Occupied and recovery

modes.

Setting Temperature

Refer to Table 1 for the default temperature setpoints. See

Owners Guide, form number 63-4356, for complete

instructions on changing the setpoints.

Table 1. Default Temperature Setpoints.

INSTALLER SETUP

NOTE: For most applications, the thermostat factory-

settings do not need to be changed. Review the

factory-settings in Table 2 and if no changes are

necessary, go to the Installer System Test

section.

The Installer Setup is used by the installer to customize

the thermostat to specific systems. Installer Setup

numbers are listed in Table 2. The table includes all the

configuration options available.

A combination of key presses are required to use the

Installer Setup feature.

—To enter the Installer Setup mode, press and hold the

Heat/Cool Settings key while pressing both the

increase ▲ and decrease ▼ keys until the first

number is displayed. All display segments appear for

approximately three seconds before the number is

displayed. See Fig. 8 and 9.

M10238B

INSTALLER SETUP

NUMBER DISPLAY

(COLUMN 2

OF TABLE 2)

FACTORY SETTING

OR OTHER CHOICE

DISPLAY (COLUMN 3

OR 5 OF TABLE 2)

—To advance to the next Installer Setup number, press

the Unoccupied Temp key.

—To return to a previous Installer Setup number, press

the Heat/Cool Settings key.

—To change a setting, use the increase ▲ or decrease

▼ key.

—To exit the Installer Setup, press the Run Program

key. The Installer Setup is automatically exited if no

key presses are made for four minutes.

Fig. 8. LED display of all segments.

Control Occupied Unoccupied

Heating 70°F (21°C) 55°F (13°C)

Cooling 78°F (25.5°C) 90°F (32°C)

62-0128—2

T7200D,E SERIES 2000 COMMERCIAL MICROELECTRONIC THERMOSTATS

Table 2. Thermostat Installer Setup Options.

(continued)

aNumber 2 must be set to 1 to extend fan operation.

bSome models may not have this feature.Table 2.

Installer Setup

Number

(Press

Unoccupied

Temp key Factory Setting

Other Choices

(Press ▲or ▼key to change) Actual

Select to change) Display Description Display Description Setting

Not used. 1 — — — — —

Fan operation

(T7200D only).

20Conventional applica-

tions where

equipment controls

fan operation in heat

mode.

1 Electric heat applications

where thermostat controls

fan operation in heat mode.

Degree

temperature

display.

14 0 Temperature is

displayed in °F. 1 Temperature is displayed

in °C.

Intelligent Fan™

operation. 17 2 Fan operates

continuously in

Occupied and

Recovery mode. Fan

operates with call for

heating or cooling in

Unoccupied mode.

0 or 1 0—Fan only operates with

calls for heating or cooling

in Occupied and

Unoccupied modes.

1—Fan operates

continuously in Occupied

mode. Fan operates with

calls for heating or cooling

in Unoccupied mode.

Keypad lockout

level (keypad

lockout is

enabled and

disabled by dip

switch 1 on

thermostat

back).

25 0 No lockout. 1 or 2 1—Lockout all keys on

thermostat except system

and fan settings, temporary

setpoint; clock and day

adjustments.

2—Lockout all keys except

set Current Day/Time,

increase ▲and decrease

▼keys.

3—Lockout all keys except

Temporary Occupied, Set

Current Day/Time (for

clock, day adjustments).

O/B Operation

(T7200E only).

29 0 0—Energize in Cool

mode. 11—Energize in Heat Mode.

Minimum off-

time for the

compressor.

33 4 4-minute minimum

off-time for the

compressor.

0, 1, 2, 3

or 5 Minimum number of minutes

(0 thru 5) the compressor will

be off between calls for the

compressor.

Temperature

display

adjustment.

37 0 No difference in

displayed

temperature and

actual room

temperature.

1 thru 6 1—Display adjusts to 1°F

(0.6°C) higher than actual

room temperature.

2—Display adjusts to 2°F

(1.1°C) higher than actual

room temperature.

3—Display adjusts to 3°F

(1.7°C) higher than actual

room temperature.

4—Display adjusts to 1°F

(0.6°C) lower than actual

room temperature.

5—Display adjusts to 2°F

(1.1°C) lower than actual

room temperature.

6—Display adjusts to 3°F

(1.7°C) lower than actual

room temperature.

62-0128—2 6

T7200D,E SERIES 2000 COMMERCIAL MICROELECTRONIC THERMOSTATS

INSTALLER SYSTEM TEST

Use the Installer System Test to check the thermostat

configurations and operation. Refer to Table 3 for a list of

the available system tests.

M4954A

SetProgram SetTemperature Change

Time/Temp

Occupied

Temp

Unoccupied

StartTime Day

System Fan

Copy

Occupied

StartTime

Run

Program

Temporary

Occupied

Continous

Unoccupied

SetCurrent

Day/Time Clear

StartTime

Unoccupied

Temp

Heat/Cool

Settings

Auto

System Fan

Mon

Room

Occupied 1

Heat

Run

Program

Test

Number System Test Description

10 to 19 Heating equipment can be turned on and

off

30 to 39 Cooling equipment can be turned on and

off

40 to 49 Fan equipment can be turned on and off

60 0 to

60 19 Keyboard keys test

70 to 79 Thermostat information including date

code, software versions and subbase

identification are displayed

Table 3. Tests Available in Installer System Test.

IMPORTANT

Review the settings to confirm that they match

the system. Press Run Program to exit the

Installer Setup. Set the current day and time

immediately.

Setting Current Day and Time

1. Press Set Current Day/Time.

NOTE: On initial power up or after an extended

power loss, 1:00 pm flashes on the LCD

until a key is pressed.

M4951B

Set Current

Day/Time

SetProgram SetTemperature Change

Time/Temp

Occupied

Temp

Unoccupied

StartTime Day

System Fan

Copy

Occupied

StartTime

Run

Program

Temporary

Occupied

Continous

Unoccupied

SetCurrent

Day/Time Clear

StartTime

Unoccupied

Temp

Heat/Cool

Settings

Mon

Set Day/Time

2. Press Day until the current day is displayed.

NOTE: Sun=Sunday, Mon=Monday,

Tue=Tuesday, Wed=Wednesday,

Thu=Thursday, Fri=Friday, Sat=Saturday.

3. Press increase ▲or decrease ▼until the current

time is displayed.

NOTE: Tapping the Set Current Day/Time changes

the time in one hour increments.

M4952B

SetProgram SetTemperature Change

Time/Temp

Occupied

Temp

Unoccupied

StartTime Day

System Fan

Copy

Occupied

StartTime

Run

Program

Temporary

Occupied

Continous

Unoccupied

SetCurrent

Day/Time Clear

StartTime

Unoccupied

Temp

Heat/Cool

Settings

Day

Tue

Set Day/Time

M4953B

SetProgram SetTemperature Change

Time/Temp

Occupied

Temp

Unoccupied

StartTime Day

System Fan

Copy

Occupied

StartTime

Run

Program

Temporary

Occupied

Continous

Unoccupied

SetCurrent

Day/Time Clear

StartTime

Unoccupied

Temp

Heat/Cool

Settings

Tue

Set Day/Time

4. Press Run Program.

To start the system test:

CAUTION

Possible Equipment Damage.

Equipment damage can result if compressor is

cycled too quickly.

The minimum off-time for compressors is bypassed

during the Installer System Test.

Press and hold the increase ▲ and decrease ▼keys, at

the same time, until 10 appears. All segments of the LCD

are displayed for three seconds before 10 appears. See

Fig. 10 and 11.

Table 2. Thermostat Installer Setup Options (Continued).

Installer Setup

Number

(Press

Unoccupied

Temp key Factory Setting

Other Choices

(Press ▲or ▼key to change) Actual

Select to change) Display Description Display Description Setting

Minimum off-

times in heating. 38 4 4—4-minute

minimum off-time. 0, 1, 2, 3,

or 5 Minimum number of minutes

(0 thru 5) the heating

equipment will be off

between calls for heat.

Installer Setup

lockout (keypad

lockout is

enabled and

disabled by dip

switch 1 on back

of thermostat).

40 0 0—No Installer Setup

lockout. 1 1—Installer Setup lockout

activated.

62-0128—2

T7200D,E SERIES 2000 COMMERCIAL MICROELECTRONIC THERMOSTATS

Heat

Auto

System Fan

Off Auto

Mon

Wait

Room

Remote

%Humid

Auto

Sav

Comm Cool Duct

Only

Recovery

Med

Cool

TueWedThuFriSatSun

Occupied 12 Override

M4916

Aux Ht

Em Ht

Set Program

Set Day/Time

Start Time Temporary Setting Enrg

Em Heat

M10257A

TEST NUMBER

NOTE: If a duct temperature sensor is installed, the duct

temperature is also displayed.

Refer to Table 4 and Thermostat Information section for

directions and results of the specific system tests.

NOTE: Press Run Program to exit the system test. The

system test times out after four minutes if there

are no additional key presses.

Fig. 10. LCD display of all segments.

Fig. 11. Test number display.

Table 4. Installer System Test Options.

Key to Press Test

Number Description

Heating Equipment Test

Heat/Cool Settings 10 Enter heating equipment test.

▲11 Heat turns on. The system fan is also energized.

▼10 Heat and system fan turn off.

Cooling Equipment Test

Heat/Cool Settings 30 Change from heating to cooling equipment test.

▲31 Cool and system fan turn on.

▼30 Cool and system fan turn off.

Fan Equipment Test

Heat/Cool Settings 40 Change from cooling to fan equipment test.

▲41 Fan turns on.

▼40 Fan turns off.

Key Operation Test

Heat/Cool Settings 60 2 Change from fan to key operation test.

Unoccupied Temp 60 0 Unoccupied Temp test number is displayed.

Occupied Temp 60 1 Occupied Temp test number is displayed.

▲60 3 Increase test number is displayed.

▼60 5 Decrease test number is displayed.

Clear Start Time 60 7 Clear Start Time test number is displayed.

Day 60 8 Day test number is displayed.

Copy 60 9 Copy test number is displayed.

Unoccupied Start

TIme

60 10 Unoccupied Start Time test number is displayed.

System

(select models)

60 11 System test number is displayed.

Fan (select models) 60 12 Fan test number is displayed.

Set Current Day/Time 60 14 Set Current Day/Time test number is displayed.

Run Program 60 15 Run Program test number is displayed.

Temporary Occupied 60 16 Temporary Occupied test number is displayed.

Occupied Start Time 60 17 Occupied Start Time test number is displayed.

Continuous

Unoccupied

60 19 Continuous Unoccupied test number is displayed.

62-0128—2 8

T7200D,E SERIES 2000 COMMERCIAL MICROELECTRONIC THERMOSTATS

M10235

BACK OF THERMOSTAT

DIP 1 IS ON

DIP 2 IS NOT USED.

M4934

M4931

M4932A

M10229

M4933A

M10290

Thermostat Information

1. Press the Heat/Cool Settings key to access the

thermostat information.

2. Press the increase ▲ key to display the production

date code. The first two large digits are the month

and the third digit is the last digit of the year.

(Example: 036 = March 1996).

3. Press the increase ▲ key again to display the

software identification code. (Example: 02 =

software ID code 2).

4. Press the increase ▲key again to display the

software revision number. (Example: 001 = revision

number 1).

5. Press the increase ▲ key again to display the

EEPROM identification code. (Example: 314 =

EEPROM ID 314).

6. Press the increase ▲ key again to display the

wallplate identification code. (Example: HP = heat

pump wallplate).

7. Press Run Program to exit the system test. The

system test times out after four minutes without any

key presses.

Setting Keypad Lockout Switch

The dip switch 1 on the back of the thermostat activates

the Installer Setup lockout feature. The switch must be set

to the ON position (up) to activate the lockout feature. See

Fig. 12. The factory setting is off (down). Remove the

thermostat from the wallplate and set the switch to ON if

keypad lockout is desired. The level of lockout is deter-

mined by the Installer Setup number 40.

Fig. 12. Set Installer Setup lockout dip switch 1

on back of thermostat.

62-0128—2

T7200D,E SERIES 2000 COMMERCIAL MICROELECTRONIC THERMOSTATS

(continued)

Symptom Possible Cause Action

Display does not

turn on. No power to thermostat. • Check that C terminal is connected to the system

transformer.

• Check for 24 Vac between C and R terminals.

— If missing 24 Vac:

— check if the circuit breaker is tripped; if so, reset the

circuit breaker.

— check if the system fuse is blown; if so, replace the

fuse.

— check if the power switch on the HVAC equipment

is in the Off position; if so, set to the On position.

— check wiring between thermostat and HVAC

equipment and replace any broken wires and

tighten any loose connections.

— If 24 Vac is present, proceed with troubleshooting.

Temperature display

is incorrect. Room temperature display

has been reconfigured. Enter Installer Setup number 37 and reconfigure the display.

Thermostat is configured for

°F or °C display. Enter Installer Setup number 14 and reconfigure the display.

Bad thermostat location. Relocate the thermostat.

Temperature settings

will not change.

(Example: Cannot set

heating higher or

cooling lower.)

Upper or lower temperature

limits were reached. Check the temperature setpoints:

• Heating limits are 40°F to 90°F (7°C to 31°C).

• Cooling limits are 45°F to 99°F (9°C to 37°C).

Unable to configure

Installer Setup. Installer Setup is locked out. Reset the dip switch 1 on the back of the thermostat to enable

keypad.

Temperature settings

change from original

setting.

Heating and cooling setpoints

are set too close together.

There is a deadband in

automatic changeover

thermostat models. Example:

cool setpoint = 72, deadband

= 3, heat setpoint = 68,

changing heat setpoint to 70

automatically changes the

cool setpoint to 73.

• Check that the heating setpoint is lower than the cooling

setpoint.

Room temperature is

out of control. Remote temperature sensing

is not working. Checkout all remote sensors.

Heating does not

turn on. No power to the thermostat. • Check that C terminal is connected to the system

transformer.

• Check for 24 Vac between C and R terminals.

— If missing 24 Vac:

— check if the circuit breaker is tripped; if so, reset the

circuit breaker.

— check if the system fuse is blown; if so, replace the

fuse.

— check if the system switch at the equipment is in

the Off position; if so, set to On position.

— check wiring between thermostat and HVAC

equipment and replace any broken wires and

tighten any loose connections.

— If 24 Vac is present, proceed with troubleshooting.

Thermostat minimum off-time

is activated and wait indicator

is displayed.

•Wait up to five minutes for the system to respond.

• Enter Installer Setup number 38. Reconfigure minimum off-

time (if required).

System selection is not set

to Heat. Set system selection to Heat.

TROUBLESHOOTING GUIDE

62-0128—2 10

T7200D,E SERIES 2000 COMMERCIAL MICROELECTRONIC THERMOSTATS

Troubleshooting Guide (continued).

Symptom Possible Cause Action

Cooling does not

turn on. No power to the thermostat. • Check that C terminal is connected to the system

transformer

• Check for 24 Vac between C and R or RC and Y

terminals.

— If missing 24 Vac:

— check if the circuit breaker is tripped; if so, reset the

circuit breaker.

— check if the system fuse is blown; if so, replace the

fuse.

— check if the system switch at the equipment is in

the Off position; if so, set to the On position.

— check wiring between thermostat and HVAC

equipment and replace any broken wires and

tighten any loose connections.

— If 24 Vac is present, proceed with troubleshooting.

Thermostat minimum off-time

is activated and wait indicator

is displayed.

• Wait up to five minutes for the system to respond.

• Enter Installer Setup number 33. Reconfigure minimum off-

time (if required).

System selection is not set to

Cool. Set system selection to Cool.

System on

indicator (flame =

heat, snowflake =

cool) is displayed, but

no warm or cool air is

Conventional heating

equipment turns on the fan

when the furnace has

warmed up to a setpoint.

Wait one minute after the on indicator lights and then check

the registers.

coming from the

registers. Heating or cooling equipment

is not operating. Verify operation of heating or cooling equipment in system

test.

Otros manuales para T7200D

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Termostato de Honeywell

Honeywell

Honeywell TH2110 Manual de usuario

Honeywell

Honeywell RTH1120 Manual de usuario

Honeywell

Honeywell Thermostats Guía del usuario

Honeywell

Honeywell WebPAD S7350B Manual de usuario

Honeywell

Honeywell RTH2510 Series Manual de usuario

Honeywell

Honeywell Lyric T5 Wi-Fi Manual de usuario

Honeywell

Honeywell TC500A-N Manual de usuario

Honeywell

Honeywell RTH2310B Manual de usuario

Honeywell

Honeywell PROGRAMMABLE THERMOSTAT RTH6350 Manual de usuario

Honeywell

Honeywell THE ROUND Y460A2003 Manual de usuario

Honeywell

Honeywell Y9420H Sundial RF2 Manual de usuario

Honeywell

Honeywell RTH2510B1000/U Manual de usuario

Honeywell

Honeywell VisionPRO TH8000 Series Manual de usuario

Honeywell

Honeywell RTH7600D Manual de usuario

Honeywell

Honeywell VisionPRO 8000 Manual de operación

Honeywell

Honeywell LYRIC T4 Manual de usuario

Honeywell

Honeywell RTHL2310 series Manual de usuario

Honeywell

Honeywell TRADELINE T8011R Manual de operación

Honeywell

Honeywell T8000C Manual de usuario

Honeywell

Honeywell Q539A Manual de usuario

Honeywell

Honeywell TL6120 Manual de usuario

Honeywell

Honeywell RLV430 Manual de usuario

Honeywell

Honeywell RTH5100B Manual de usuario

Honeywell

Honeywell RTH6500 Manual de usuario

Manuales populares de Termostato de otras marcas

EWELLY

EWELLY EW-181 Manual de usuario

Prolon

Prolon T1100 Instrucciones de instalación

Computherm

Computherm Q20 Manual de usuario

Heatmiser

Heatmiser neoStat Manual de usuario

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario

Saswell

Saswell SAS920XWHB-7-S-RF Guía

Aircalo

Aircalo TFP1-ET85P2 Manual de usuario

Carrier

Carrier DEBONAIR 33CS Manual de usuario

Lennox

Lennox iHarmony Zone Thermostat Instrucciones de montaje

Gemtech

Gemtech GT7000 Manual de instrucciones

Rollei

Rollei Smartes 45000 Manual de usuario

Sinope

Sinope TH1300RF Manual de usuario

NuTone

NuTone NTBZ48 Instrucciones de funcionamiento originales

Stelpro

Stelpro MAESTRO ASMT402AD Manual de usuario

Aube Technologies

Aube Technologies TH305 Manual de usuario

Powtier Controls

Powtier Controls 505MST Manual de usuario

Kanmor

Kanmor Zone Control 369e Manual de usuario