Honeywell Informa Manual de usuario

The Informa is a keypad unit that has the capability

of dialling prerecorded speech messages over a

telephone line. It is installed as part of your intruder

system, so that when the system detects an intrusion

the external siren will sound to alert your neighbours

and the Informa will dial a programmed telephone

number and play a recorded speech message to alert

someone else to the intrusion.

For example, the Informa can contact a friend or

relative who lives close to your home, who can

investigate the alarm and call the police if necessary.

What Does the Informa Need to Know?

Before Informa can work, you must program it with

the telephone numbers to use and record the alarm

messages to be played.

Features

Call Setup

Speech Dialler

Operating Instructions

The Informa can memorise four spoken messages.

Message number 1 (referred to as a ‘location

message’) may be up to 11 seconds long, and is used

to identify the location of the Informa; messages 2,

3 and 4 (referred to as ‘alarm messages’) may be up

to 3 seconds long and identify the type of alarm.

There are three types of alarm: Intruder, Personal

Attack (PA) and Fire. For each alarm call, the

Informa plays the location message, followed by

alarm message 2, 3 or 4.

So a typical call could be:

Location message: “This is the Alarm Panel at the

house of Fred Smith in Wigan”, followed

immediately by alarm message: “The intruder alarm

has been activated”.

Your installer will tell you which alarm messages can

be used with your system.

Messages

Telephone Numbers

The Informa call setup can work in one of two ways:

1. In the first case, it begins by calling the first

programmed number and plays the message that

corresponds to the type of alarm.

If two different alarms have occurred, both

corresponding alarm messages are played. If the

message is not acknowledged, it will call the

second, then the third number, until it receives

an acknowledgement. See Acknowledging

Messages, on page 3.

The Informa calls each number in sequence, so

you should ensure that the first number

programmed belongs to the person most likely

to answer the call.

2. In the second case, the telephone number called

corresponds to the type of alarm that has

occured, so that only one designated contact is

called, depending upon the type of alarm:

Intruder, PA or Fire.

If the call is not acknowledged, the Informa will

continue to call the same number seven more

times.

Check with the installer which type of setup has

been programmed.

Note: In both cases, if a Follow Me number has

been programmed, this will be the first number

called. See Setting the Follow Me Number, on

page 3.

Up to three telephone numbers can be designated

and memorised by the Informa. It is recommended

that these numbers belong to friends or relatives who

live close to your home, who can carry out an initial

investigation of the alarm, then contact the police, if

appropriate.

The Informa can also be programmed to contact your

mobile phone, but unless you are close to home this

may not be very useful.

When a call is received, it must be acknowledged in

order to end the call process, so ensure that your

designated contacts know how to acknowledge a

call.

Informa – Speech Dialler

Programming the Informa

Informa is on standby when only the green Power

LED “ON” is lit. To program the Informa, you must

enter programming mode by keying in a 4-digit code

on the keypad. This code is factory set to 0123 but

your installer may have changed it.

Key in the code. If it is valid, all 4 red LED

indicators will light. Once in programming mode

you can carry out any of the functions on the

following pages:

The Informa Tones

The Informa uses two distinct tones to confirm an

action or to alert you to an error:

To confirm an action, the Informa sounds a fast

double-beep.

To alert you to an error, the Informa sounds two

long tones.

Changing a Telephone Number

a) Press TEL.

b) Press the number corresponding to the

memorised telephone number to be changed

(1, 2 or 3).

c) Enter the digits of the telephone number; 21

digits are allowed or the number is accepted

automatically upon entry of the 21st digit.

If a number of less than 21 digits is required,

press Tel to end the entry of the number.

If you make a mistake press QUIT to cancel.

Note:The Informa cannot contact the emergency

services directly. It will not accept any telephone

number starting with 999 or 112.

Deleting a Telephone Number

a) Press TEL.

b) Press the number corresponding to the

telephone number to be deleted (1, 2 or 3).

c) Press TEL.

Recording a Message

a) Press REC.

LEDs 1 to 4 flash.

b) Press the message number to be recorded

(1, 2, 3 or 4).

Informa will pause for 1 second then sound a

tone for 1 second.

c) Now speak clearly into the microphone, which

is just below the LEDs.

The Informa automatically stops recording at

the end of the message duration. After a short

interval, it plays back the message just recorded.

If the announcement to be recorded in message 1 is

much shorter than 11 seconds you can stop the

recording at any time by pressing PLAY.

Refer also to Messages, on the previous page.

Playing Back Messages

a) Press PLAY. LEDs 1 to 4 will flash.

b) Press the message number to be played

(1, 2, 3 or 4).

After a short interval, Informa plays the selected

message.

Controlling the Volume

From programming mode, you can alter the volume

of the messages when they are played back.

By default the Informa uses volume Medium 1.

Key in your 4-digit customer code.

a) Press 1 to enter volume control mode.

b) Press:

[1] to select Minimum volume

[2] to select Medium 1 volume

[3] to select Medium 2 volume

[4] to select Maximum volume.

Press QUIT to leave programming mode.

Testing the Informa

The Informa can perform a test call, in order to check

that the telephone numbers have been set up

correctly.

During a test call the playback speaker will be turned

on so that you can hear how the call progresses. To

generate a test call:

a) Press TEST. LEDs 1 to 3 flash.

Operating Instructions

Once programmed, the Informa needs no further

programming or attention. Set and unset your alarm

system as directed by your installer. In the event of

an alarm, Informa will carry out its function reliably

and silently.

Cancelling a Call

If you accidentally set off your alarm system, the

Informa will attempt to communicate its alarm

message. You can stop this by keying in your code on

the Informa keypad. All four LEDs flash for several

seconds to confirm that the call has been cancelled.

Acknowledging Messages

The person who answers the telephone call from the

Informa must always acknowledge the call.

This is done as follows:

a) When you answer a call from an Informa, listen to

the message.

Using the Informa

At the end of the message the Informa produces a

single tone for 1 second.

b) Press the * (star) key on the telephone for at least

1 second. You must do this within 5 seconds of

the tone.

The Informa repeats the tone for 1 second.

c) Again, you have 5 seconds in which to press the

* key for 1 second.

The Informa sounds 2 short beeps to indicate

that it has received the acknowledgement and

then hangs up.

Note that it is only possible to acknowledge the

call with a tone dialling telephone.

Setting the Follow Me Number

The Informa also has a Follow Me number, which

allows it to call you wherever you are.

You can easily reprogram this number each time that

you leave the house and set the alarm system. If a

Follow Me number has been programmed, the

Informa always attempts to contact this number first.

The Follow Me number is cancelled each time the

alarm system is unset.

The Follow Me number can be changed without

entering programming mode.

To set the Follow Me number:

a) Press TEL.

b) Key in the telephone number (up to 20 digits).

c) Press TEL.

b) Press the number corresponding to the telephone

number to be called (1 to 3).

The Informa dials the number, plays the location

message followed by alarm message 2 and

listens for the acknowledgement signal. If

it receives a valid signal, it hangs up and all 4

LEDs light steadily. If it fails to receive an

acknowledgement, it repeats its messages 7

times, then hangs up and all 4 LEDs flash.

Press TEST if you wish to cancel this procedure.

Changing the Code

The factory set user code is 0123. If your installer

has not already changed this to a number of your

choice, you can change it as follows:

a) Press 8.

b) Key in the new 4-digit code.

Informa does not accept certain codes, in which

case it sounds the two-tone error tone.

Leaving Programming Mode

Press QUIT at any time to finish programming.

Informa – Speech Dialler

Installer Details

You too could benefit from the added security

and peace of mind only an INFORMA can bring!

Contact your Installer (details below)

Company: _____________________________

Contact: _____________________________

Address: _____________________________

_______________________________________

Honeywell Security & Custom Electronics

Newhouse Industrial Estate

Motherwell

ML1 5SB

www.honeywell.com/security/uk

You too could benefit from the added security

and peace of mind only an INFORMA can bring!

Contact your Installer (details below)

Company: ____________________________

Contact: ____________________________

Address: ____________________________

______________________________________

Company: _____________________________

Contact: _____________________________

Address: _____________________________

_______________________________________

INFORMA

Acknowledgement Instructions

When you answer a call from an Informa, listen

to the message.

At the end of the message Informa produces a

single tone for 1 second.

Press the * (star) key on the telephone for at

least 1 second. (You must do this within 5 secs

of the tone.)

Informa repeats its tone for 1 second.

Press the * (star) key again for 1 second.

The Informa then sounds 2 short beeps to

confirm receipt of the acknowledgement and

disconnects.

Cut out the acknowledgement instructions above and carry them with you for reference.

INFORMA

Acknowledgement Instructions

When you answer a call from an Informa, listen

to the message.

At the end of the message Informa produces a

single tone for 1 second.

Press the * (star) key on the telephone for at

least 1 second. (You must do this within 5 secs

of the tone.)

Informa repeats its tone for 1 second.

Press the * (star) key again for 1 second.

The Informa then sounds 2 short beeps to

confirm receipt of the acknowledgement and

disconnects.

IU1-0276 Revision 1 IU- revision-

Tabla de contenidos

Otros manuales de Sistema de seguridad de Honeywell

Honeywell

Honeywell LYNX Touch L7000 Series Manual de usuario

Honeywell

Honeywell LXL-1000 Manual de usuario

Honeywell

Honeywell Notifier P700N Manual de usuario

Honeywell

Honeywell ADEMCO VISTA-10P Manual del propietario

Honeywell

Honeywell Esser 804950 Manual de usuario

Honeywell

Honeywell Lyric SIXSIREN Manual de usuario

Honeywell

Honeywell Galaxy Keyprox Especificaciones técnicas

Honeywell

Honeywell LYNX Touch L7000 Series Manual de usuario

Honeywell

Honeywell HS923GPRS Manual de usuario

Honeywell

Honeywell VAM Manual de usuario

Honeywell

Honeywell LYNX Touch Series Manual de usuario

Honeywell

Honeywell ADEMCO LYNXR Series Manual de usuario

Honeywell

Honeywell LYNX Touch Security System Manual de usuario

Honeywell

Honeywell Lyric Manual de usuario

Honeywell

Honeywell HS-6270 Manual de usuario

Honeywell

Honeywell ADEMCO VISTA-12A Instrucciones de montaje

Honeywell

Honeywell LYNX Touch L5210 Series Instrucciones de montaje

Honeywell

Honeywell ADEMCO VISTA-40 Manual de usuario

Honeywell

Honeywell Lynx Plus Series Instrucciones de funcionamiento

Honeywell

Honeywell Apex Destiny 4100 Manual de usuario

Honeywell

Honeywell LYNXR-I Series Instrucciones de funcionamiento

Honeywell

Honeywell LYNX Manual de usuario

Honeywell

Honeywell FG8MS Manual de usuario

Honeywell

Honeywell VISTA-32FBPT Manual de usuario

Manuales populares de Sistema de seguridad de otras marcas

Inner Range

Inner Range Concept 2000 Manual de usuario

Climax

Climax Mobile Lite R32 Instrucciones de montaje

CADDX

CADDX NX-6 Manual de usuario

FBII

FBII XL-31 Series Manual de usuario

Johnson Controls

Johnson Controls PENN Connected PC10 Manual de usuario

Aeotec

Aeotec Siren Gen5 Manual de usuario

Blaupunkt

Blaupunkt SA 2700 Manual de usuario

IDEAL

IDEAL Accenta Manual del propietario

AJAX

AJAX DoubleButton Manual de usuario

Swann

Swann SW-P-MC2 Manual de usuario

Ecolink

Ecolink Siren+Chime Manual de usuario

Digital Monitoring Products

Digital Monitoring Products XR150 Manual de usuario

EDM

EDM Solution 6+6 Wireless-AE Manual de usuario

Highway Safety Group

Highway Safety Group EA401 Manual de usuario

Siren

Siren LED GSM Manual de usuario

Detection Systems

Detection Systems 7090i Instrucciones de montaje

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manual de usuario

Siemens

Siemens FDM273 Manual de usuario