Honeywell HD28C4HR6 Manual de usuario

Document 900.0275 – 10/05 – Rev 1.01

Installation Guide

Premium Vandal

Dome Camera

NTSC / PAL

HD28C4HR6 HD28C4HR6X

HD28C4HR9 HD28C4HR9X

HD28W4HR6 HD28W4HR6X

HD28W4HR9 HD28W4HR9X

HD28D4HR6 HD28D4HR6X

HD28D4HR9 HD28D4HR9X

Revisions

Issue Date Revisions

1.00 09/05 New document.

1.01 10/05 Changed HD28R to HD28 throughout,

removed utp & fiber termination boards

updated back cover.

Rev 1.01 ii Document 900.0275

10/05

Rev 1.01 iii Document 900.0275

10/05

Warnings

Installation and servicing should be performed only by qualified and experienced

technicians to conform to all local codes and to maintain your warranty.

WARNING! The use of CSA Certified/UL Listed Class 2 power adapters

is required to ensure compliance with electrical safety

standards.

Explanation of Graphical Symbols

WEEE (Waste Electrical and Electronic Equipment). Correct disposal

of this product (applicable in the European Union and other European

countries with separate collection systems). This product should be

disposed of, at the end of its useful life, as per applicable local laws,

regulations, and procedures.

RISK OF ELECTRIC

SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE THE COVER.

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL

THIS SYMBOL INDICATES THAT

DANGEROUS VOLTAGE

CONSTITUTING A RISK OF

ELECTRIC SHOCK IS PRESENT

WITHIN THE UNIT.

THIS SYMBOL INDICATES THAT

IMPORTANT OPERATING AND

MAINTENANCE INSTRUCTIONS

ACCOMPANY THIS UNIT.

CAUTION

Rev 1.01 iv Document 900.0275

10/05

FCC Compliance Statement

Information to the User: This equipment has been tested and found to comply

with the limits for a Class A digital device. Pursuant to Part 15 of the FCC Rules,

these limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the user will be required

to correct the interference at his own expense.

Caution Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to

operate the equipment.

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la Classe A est conforme à norme NMB-003 du

Canada.

Manufacturer’s Declaration of Conformance

The manufacturer declares that the equipment supplied with this guide is

compliant with the essential protection requirements of the EMC directive 89/336/

EEC and the Low Voltage Directive LVD 73/23 EEC, conforming to the

requirements of standards EN 55022 for emissions.

Rev 1.01 Document 900.0275

10/05

Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Unpack Everything . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Equipment Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Mounting the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Preparing the Mounting Surface. . . . . . . . . . . . . . . . . . . . . . . . . 2

Installing the Conduit Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Wiring Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Connecting the Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Adjusting the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Dip Switch Functions (Color Cameras, Including TDN Models) .6

Adjustment Method (Color Cameras) . . . . . . . . . . . . . . . . . . . . .7

White Balance Adjustment Method (Color Cameras) . . . . . . . . .7

Manually Setting Shutter Speed (Color Cameras) . . . . . . . . . . .8

Dip switch functions (WDR cameras) . . . . . . . . . . . . . . . . . . . . . 9

Adjustment method (Wide Dynamic Range Cameras) . . . . . . . .9

Adjusting the Line Lock (Vertical Phase) for 24 VAC Operation 10

Adjusting the Backlight Compensation . . . . . . . . . . . . . . . . . . .10

Securing the Enclosure Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Routine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Warranty and Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Cable Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Rev 1.01 1 Document 900.0275

10/05

Introduction

The HD28 Series is Honeywell’s premium line of vandal-resistant, fully-integrated

CCTV cameras. The HD28 series enclosure is designed for easy installation and

setup.

Before You Begin

Unpack Everything

Check that the items received match those listed on the order form and packing

slip. The HD28 series packing box should include, in addition to this User Guide

• One HD28 series camera

• One hardware kit

• One mounting template

• One product warranty

If any parts are missing or damaged, contact the dealer you purchased the

camera from or call Honeywell Customer Service (see “Warranty and Service” on

page 12).

Equipment Required

You will require the following tools to complete the installation:

• Phillips screwdriver

• Mounting screws. Use mounting screws appropriate to your installation

(capable of holding at least twice the weight of the camera).

Please read this guide carefully

before you install the HD28

series camera. Keep this guide

for future reference.

Rev 1.01 2 Document 900.0275

10/05

Installation

Your HD28 camera is weather-sealed for indoor or outdoor locations. The wiring

can be completely concealed for maximum vandal and tamper resistance.

Mounting the Camera

The HD28 camera is designed to be surface mounted on a wall or ceiling.

Preparing the Mounting Surface

1. Affix the mounting template to the mounting surface (see Figure 1).

2. Pre-drill four holes as indicated on the template, using the recommended

hole size for the screws being used.

3. Drill out the conduit hole, if required (see Installing the Conduit Plug).

4. Connect the wiring (see Connecting the Wiring).

5. Mount the camera base to the wall or ceiling using mounting screws (not

supplied) capable of holding at least twice the weight of the camera.

Note Alternate fasteners (preferably stainless steel) can be used, provided

they are not larger than the screw holes on the mounting template.

Figure 1 Mounting Template Guide

WallMount

recommended

thisway

Mounting screws

appropriate to your

installation (not

supplied)

Rev 1.01 3 Document 900.0275

10/05

Installing the Conduit Plug

Your HD28 enclosure comes with a conduit plug pre-installed in the 1/2” conduit

entry on the back of the housing. This plug may be removed and installed in the

side 3/4” conduit entry (see Figure 2).

Figure 2 Conduit Plug Installation

Caution If a conduit is not used for cable routing, install the rubber

grommet in the conduit hole, then slit the grommet and feed

the wiring through. Seal the grommet to prevent moisture from

entering the housing.

Back View Side View

Screw

Retainer plate

Gasket Conduit plug

Rev 1.01 4 Document 900.0275

10/05

Wiring Options

Your HD28 Series camera is supplied with a coaxial termination board mounted

to the bottom of the enclosure. All connections are made here (see Figure 3).

Figure 3 Wiring Options

Connecting the Wiring

1. Pull the cables through either the back or the side conduit.

2. To minimize moisture leaking into the housing, position the enclosure with

the conduit pointing down. Apply an appropriate sealant around the conduit

connection.

Adjusting the Camera

To adjust the HD28 camera:

1. Apply 12 VDC or 24 VAC to the camera and monitor the video signal.

2. Loosen the screws that lock the gimbal assembly in place (see Figure 4).

3. Adjust the camera carrier to the desired view (see Figure 4).

4. Tighten the screws to lock the gimbal assembly in place.

Note Orient the camera as shown in Figure 4 to maintain the correct

picture orientation.

Coax Termination Board

Case/

Ground

Not used

Power

AudioVideo

Rev 1.01 5 Document 900.0275

10/05

Figure 4 Gimbal Adjustment

Adjusting the Lens Focus

Lenses are pre-focused at the factory but may require a final adjustment after

installation in the unlikely event the optical effect of the dome causes a slight

defocusing of the lens.

TECH TIP! To check the focus, hold the dome over the lens while making

any adjustments.

To adjust the camera direction, view angle and focus, connect the service

monitor cable (supplied) to the video monitor output.

Tilt

Pan

Horizontal rotation

Legend

1 = Pan rotation

2 = Horizontal rotation

3 = Tilt rotation

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cámara de seguridad de Honeywell

Honeywell

Honeywell HD40 Series Manual de usuario

Honeywell

Honeywell HCCM474M Manual de usuario

Honeywell

Honeywell HD4D Series Manual de usuario

Honeywell

Honeywell OptiCAM-IR Instrucciones de montaje

Honeywell

Honeywell HD31H(X) Manual de usuario

Honeywell

Honeywell HCD484LX Manual de usuario

Honeywell

Honeywell HD4D3S Manual de usuario

Honeywell

Honeywell EQUIP Series Manual del operador

Honeywell

Honeywell Performance H4D3PRV2 Manual de usuario

Honeywell

Honeywell HCM574L Manual de usuario

Honeywell

Honeywell HSGN502 Manual de usuario

Honeywell

Honeywell Lyric C2 Manual de usuario

Honeywell

Honeywell HDT Manual de usuario

Honeywell

Honeywell HEIPTZ-2201W-IR Manual de usuario

Honeywell

Honeywell EQUIP HD4DIP Manual de usuario

Honeywell

Honeywell HD4DIR Manual de usuario

Honeywell

Honeywell ScanDome II HSDN-251NS/PS Manual del propietario

Honeywell

Honeywell equIP Series S Manual de usuario

Honeywell

Honeywell HD3DH Manual de usuario

Honeywell

Honeywell Introduces HCC-745PTW Manual de usuario

Honeywell

Honeywell 2450Cm Series Manual de usuario

Honeywell

Honeywell HD55IP Manual de usuario

Honeywell

Honeywell HZC-755N/P Series Manual de usuario

Honeywell

Honeywell HD3C Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario