Honeywell SILENT KNIGHT RA-2000 Manual de usuario

RA-2000 Remote Annunciator

Installation

The optional Model RA-2000 Remote Annunciator, shown in

Figure 1, performs the same functions as the on-board

annunciator. Operation is identical. The RA-2000 can be surface

or flush monted.

Up to 8 RA-2000s can be added to the IFP-2000 system.

Figure 1: Model RA-2000 Remote Annunciator

RA-2000 installation involves the following steps:

1. Make sure power is off at the panel.

2. Mount the RA-2000 in the desired location (see Section

“Mounting the RA-2000” ).

3. Connect the RA-2000 to the panel (see Figure 2).

4. Use the dipswitches on the back of the RA-2000 to assign

an ID# to the RA-2000 (see Section 4.10.1 of Manual P/N

151430).

5. The RA-2000 module must be added to the system through

programming. JumpStart AutoProgramming will add the

module automatically (refer to Manual P/N 151430).

Wiring Connections

Wire the RA-2000 to the FACP as Shown in Figure 2.

Figure 2: SBUS Connections

Specifications

Mounting the RA-2000

This section of the manual describes mounting the remote

annunciator. The annunciator can be flush- or surface-mounted.

Flush Mounting

This section of the manual describes flush mounting.

Follow these steps to flush mount the RA-2000

1. The back box dimensions are 9-3/8" w x 8-3/8" h. The

minimum depth 2". The back box can be mounted prior to

the complete installation of the RA-2000 using any of the

mounting holes shown in Figure 3.

Figure 3: Back Box Mounting Holes

2. Remove knockout holes as needed for wires. See Figure 4

Parameter Value

Operating Voltage: 24 VDC

Current Standby: 25 mA

Alarm: 50 mA

Operating Temperature: 0° to 49° C (32° to 120° F)

Dimensions:

Flush

Mount:

Overall: 12-1/4” W x 11.5” H x 7/8” D

31.1 cm W x 29.2 cm H x 2.2 cm D

See “Flush Mounting” for back box

dimensions.

Surface

Mount:

Including trim ring:

12-1/4” W x 11.5” H x 3” D

31.1 cm W x 29.2 cm H x 7.6 cm D

Mounting Holes

firealarmresources.com

Model RA-2000 Installation Instructions

2P/N 151443 Rev A

7550 Meridian Circle, Suite 100

Maple Grove, MN 55369-4927

763-493-6455 or 800-328-0103

Fax: 763-493-6475

www.silentknight.com

for backbox knockout locations

Figure 4: Back Box Knockout Locations

3. Wire the Annunciator board to the main control panel. See

Figure 2.

4. Attach the annunciator and door assembly to back box as

shown in Figure 5 using the supplied screws.

Figure 5: Attaching Annunciator/Door Assembly to

Backbox

Surface Mounting

The Model RA-2000TG/TR trim ring kit is available for use

when surface mounting.

1. Remove the desired knock out. See Figure 4.

2. To properly mount the back box, insert a single screw into

the key shaped mounting hole. Do not tighten all the way.

See Figure 6.

Place a level on top of the back box, with the back

box level insert the rest of the mounting screws.

Figure 6: Back Box Surface Mount Holes

3. Run wires to the control panel.

4. Place the trim ring over the back box as shown in Figure 7.

Figure 7: Installing Trim Ring

5. Attach the Door assembly to the back box using screws

provided.

6. After the annunciator wiring to the panel has been

completed, replace the electronic assembly in the back box.

Place the bezel over the back box and tighten the set screws

on the bezel.

Wire Knockouts

Key Shaped

Mounting Hole

Back Box

Mounting Holes

firealarmresources.com

Otros manuales de Mando a distancia de Honeywell

Honeywell

Honeywell ADEMCO 5804BDV Manual de usuario

Honeywell

Honeywell 5804BD Manual de usuario

Honeywell

Honeywell YTH5320R Manual de usuario

Honeywell

Honeywell Silent Knight 6860 Manual técnico

Honeywell

Honeywell TrueIAQ Manual de usuario

Honeywell

Honeywell DF-RC Manual de usuario

Honeywell

Honeywell HCW 23 Manual de usuario

Honeywell

Honeywell REM5000R01 Manual de usuario

Honeywell

Honeywell NOTIFIER LCD6000A Manual de instrucciones

Honeywell

Honeywell ADEMCO 5804BDV-CN Manual de usuario

Honeywell

Honeywell FocusPRO 6000 Series Manual de usuario

Honeywell

Honeywell DG115EZIAQ - TrueIAQ Digital IAQ Control Manual de usuario

Honeywell

Honeywell Power Presenter RF Manual de usuario

Honeywell

Honeywell TCC800M Manual de usuario

Honeywell

Honeywell Wireless Remote Control Manual de usuario

Honeywell

Honeywell REDLINK ERM5220R Manual de usuario

Honeywell

Honeywell TS607 Manual de usuario

Honeywell

Honeywell ADEMCO 5804BD Manual de usuario

Honeywell

Honeywell UDC 2300 Manual de usuario

Honeywell

Honeywell HS3FOB1S Manual de usuario

Honeywell

Honeywell 40015 Manual de usuario

Honeywell

Honeywell 42136 Manual de usuario

Honeywell

Honeywell TFU 22 Manual de usuario

Honeywell

Honeywell 5805-6A Manual de usuario

Manuales populares de Mando a distancia de otras marcas

Panasonic

Panasonic EUR7622KB0 Manual de usuario

Bang & Olufsen

Bang & Olufsen Beo4 Manual de usuario

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manual de usuario

Multiplex

Multiplex PROFI TX 9 Manual de usuario

One Remote

One Remote RMB4 Manual de usuario

FUTABA

FUTABA 9ZAP - PART2 Manual de usuario

HR Matic

HR Matic HR MULTI 3 Manual de usuario

Yamaha

Yamaha ACC-GNRST-30-20 Manual de usuario

EisSound

EisSound KBSOUND Manual de usuario

Marantz

Marantz RC101 Manual de usuario

Conrad

Conrad FS20 TC6 Manual de usuario

Anritsu

Anritsu MP1777A Manual de usuario

Niles

Niles WVC100 Guía de solución de problemas

RCA

RCA RCU1300 Manual de usuario

Bang & Olufsen

Bang & Olufsen BEO6 Manual de usuario

GE 94901 Manual de usuario

Onbon

Onbon YQ1-75 Manual de usuario

FUTABA

FUTABA R7108SB Instrucciones de instalación