Honeywell REDLINK ERM5220R Manual de usuario

INSTALL GUIDE

33-00135EFS-07

Home

ERM5220R

Equipment Remote Module

WITH REDLINK™ WIRELESS TECHNOLOGY

Table of Contents

About the ERM5220R 2

Installation Checklist 3

Terminal Designations 4

Installation 6

Checkout 12

Troubleshooting 13

Specifications 15

5 Year Warranty 17

CAUTION

Read these installation instructions completely and follow them

carefully.

Installation must be performed by a qualified service technician

and must comply with local codes.

Disconnect power to all relevant devices before installing or

servicing the ERM.

Failure to connect the device according to these instructions may

result in damage to the device, the controls, and/or personal injury.

33-00135EFS_D.book Page 1 Friday, September 8, 2017 1:59 PM

33-00135EFS—07 2

About the ERM5220R

Fig. 1.

• Wireless RedLink™ communication between condensing unit/

compressor or boiler and thermostat.

• Eliminates the need to run additional wires to your equipment, for

example, during a heat pump upgrade.

• Suitable for outdoor use.

• Temperature sensor terminals for outdoor temp sensors or indoor

freeze protection.

• LEDs for easy installation checkout.

• May reduce damage to homes since wiring/drilling is eliminated.

NOTE: The ERM5220R is compatible with updated

models THX9421R5021, TH8321R1001,

TH8320R1003, and TH8110R1008.

THM5421R1021 EIM is also required with

THX9421R5021. Optional with other models.

MCR35654

ERM

WIRE

CONDENSING

UNIT

THERMOSTAT

ERM

BOILER

33-00135EFS_D.book Page 2 Friday, September 8, 2017 1:59 PM

333-00135EFS—07

Installation Checklist

MATERIALS SUPPLIED:

• ERM5220R

• Wall Anchors (x2) and Mounting Screws (x2)

• Extra Cover Screw (optional)

• Installation Instructions

TOOLS NEEDED (NOT SUPPLIED):

•Drill

• Nut Driver Attachment for Drill

• Wire Stripper

• Small Flathead Screwdriver

• Phillips Screwdriver

• 120/240 V to 24 V Transformer (optional)

M35671

INSTALL GUIDE

33-00135EFS-03

ERM5220R

Equipment Remote Module

WITH REDLINK™ WIRELESS TECHNOLOGY

Table of Contents

About the ERM5220R 2

Installation Checklist 3

Terminal Designations 4

Installation 6

Checkout 12

Troubleshooting 14

Specifications 16

5 YearWarranty 18

CAUTION

Read these installation instructions completely and follow them

carefully.

Installation must be performed by a qualified service technician and

must comply with local codes.

Disconnect power to all relevant devices before installing or

servicing the ERM.

Failure to connect the device according to these instructions may

result in damage to the device, the controls, and/or personal injury.

M35669 M35672

M35670

33-00135EFS_D.book Page 3 Friday, September 8, 2017 1:59 PM

33-00135EFS—07 4

Terminal Designations

Fig. 2. Terminal Designations for Compressor.

M35655

JRCYDLS1 S1

TERMINALS FOR 10K OHM TEMPERATURE SENSOR. CAN BE USED TO SENSE OUTDOOR TEMPERATURES WHICH WILL BE DISPLAYED

ON A COMPATIBLE RedLINK THERMOSTAT.

COMPRESSOR LINE FAULT TERMINAL. FAULT OCCURRENCE WILL BE COMMUNICATED TO COMPATIBLE RedLINK THERMOSTAT.

COMPRESSOR DEFROST TERMINAL. DEFROST OCCURRENCE WILL BE COMMUNICATED TO COMPATIBLE RedLINK THERMOSTAT.

O/B TERMINAL FOR REVERSING VALVE ON HEAT PUMP.

SECOND STAGE OF TWO STAGE COMPRESSOR.

FIRST STAGE OF TWO STAGE COMPRESSOR.

TERMINALS FOR 24VAC POWER.

TERMINAL FOR JUMPER. JUMPER BETWEEN J AND R SHOULD BE IN PLACE FOR COMPRESSOR USE.

THE “D” TERMINAL OPERATES AS AN INPUT FOR DEFROST. ACTIVE INPUT ON “D” TERMINAL WILL POWER AUX1. IF “D” TO AUX1 IS NOT DESIRED, DO NOT

CONNECT “D” TERMINAL TO THE ERM5220R. THIS FEATURE IS ONLY ACTIVE WHEN THE THE ERM5220R IS CONFIGURED FOR USE WITH A COMPRESSOR

TERMINAL DESIGNATIONS FOR COMPRESSOR

O/B

33-00135EFS_D.book Page 4 Friday, September 8, 2017 1:59 PM

533-00135EFS—07

Fig. 3. Terminal Designations for Boiler.

M35656A

JRCYO/B

TDLS1 S1

TERMINALS FOR 10K OHM TEMPERATURE SENSOR. CAN BE USED FOR FREEZE PROTECTION IN THE CASE OF THE THERMOSTAT

LOSING THE SIGNAL TO THE ERM. SENSOR MUST REMAIN INDOORS TO BE USED FOR FREEZE PROTECTION.

TERMINAL FOR HEAT CALL.

TERMINALS FOR 24VAC POWER.

TERMINAL FOR JUMPER. JUMPER BETWEEN J AND R SHOULD BE REMOVED FOR BOILER USE.

TERMINAL DESIGNATIONS FOR BOILER

TERMINAL FOR HEAT CALL.

NOTE: ERM WILL NOT SUPPORT SERIES20 OPERATION. WHEN CONFIGURED AS A BOILER, THE Y RELAY SHALL BE OFF AT ALL TIMES.

33-00135EFS_D.book Page 5 Friday, September 8, 2017 1:59 PM

33-00135EFS—07 6

INSTALLATION

IMPORTANT

• The ERM is not compatible with RedLink Zone boards.

• To ensure that the ERM will receive a wireless signal at the

desired installation location, follow steps 1 to 5 in the Wiring

section.

• If your location has metal siding, the ERM’s signal may be

affected. If there is no communication or poor signal strength,

consider a different location.

• A Prestige (with EIM) or VisionPRO (with or without EIM) will

only allow one of the following configurations:

1) Enrolled with a single boiler configured ERM;

2) Enrolled with a single compressor configured ERM;

3) Enrolled with a single boiler configured ERM and enrolled

with a single compressor configured ERM.

Wiring

1. Make sure power to compressor/boiler is off.

2. Remove the front cover by loosening the cover screw and lifting

up from the bottom of the ERM.

3. Remove 3 to 4 inches of the cable’s outer sheathing, then

remove 3/8 to 1/2 inch of insulation from each wire.

Fig. 4. Cable prepared for wiring.

M35674

33-00135EFS_D.book Page 6 Friday, September 8, 2017 1:59 PM

733-00135EFS—07

4. For compressor applications: Leave the jumper between termi-

nals J and R in place.

For boiler applications: Remove the jumper between terminals

J and R.

Fig. 5. Terminal Designations showing the jumper

between J and R terminals.

5. For compressors and boilers: Connect a 24 VAC power source

to the R and C terminals on the ERM.

Fig. 6.

6. Connect terminals from the ERM to the appropriate terminals

on the compressor/boiler control board.

MCR35657

CYDLS1 S1

FOR COMPRESSOR:

Jumper J and R

FOR BOILER:

Remove Jumper

JRO/B

M35658

CYDLS1 S1

24V CAN COME FROM AIR HANDLER

(COMPRESSOR APPLICATION)

OR EXTERNAL TRANSFORMER

JRO/B

VAC

V c.a.

33-00135EFS_D.book Page 7 Friday, September 8, 2017 1:59 PM

33-00135EFS—07 8

COMPRESSOR

Fig. 7.

BOILER

Fig. 8.

IMPORTANT

If the ERM was previously used with a compressor and will now

be used with a boiler:

1) un-enroll the ERM at the thermostat;

2) remove the jumper on the ERM;

3) designate Radiant Heat for Heating System Type

(ISU 2000) in your thermostat.

M35668

CYDLS1 S1

JRO/B

CYDL

Y2 O/B

VAC

V c.a.

10K OHM OUTDOOR

TEMPERATURE

SENSOR (OPTIONAL)

EQUIPMENT CONTROL BOARD

M35673

CYDLS1 S1

JRO/B

EQUIPMENT

CONTROL

BOARD

10K OHM INDOOR

TEMPERATURE

SENSOR

(RECOMMENDED)

VAC

V c.a.

33-00135EFS_D.book Page 8 Friday, September 8, 2017 1:59 PM

933-00135EFS—07

Once power is connected, the “Compressor” (or “Boiler”) LED should

illuminate green. (Fig. 9)

Fig. 9.

7. For compressors and boilers:

Put the thermostat in pairing mode.

New thermostat installation: When going through the initial setup the

thermostat display will ask “TSTAT CONTROLS AN EQUIP MODULE”.

This refers to an EIM, not an ERM. See note below. The next screen

says “connect RedLINK Accessories?” The ERM is an accessory, so

select “yes”, and then “next”.

Existing thermostat installation: Select menu - installer options -

wireless manager - add device. See thermostat installation guide for

assistance.

NOTE: The ERM (equipment remote module) is not an EIM

(equipment interface module).

• If using a Prestige IAQ thermostat, the EIM (THM5421R) is

always needed, whether the ERM is used or not.

• If using a RedLINK VisionPRO model, the EIM is not needed

if: (a) there are wire connections to R and C at the

thermostat subbase and the thermostat controls hot

water heat only (no cooling).

(b) the R and C as well as furnace or air-handler wires are

connected to the subbase of the thermostat.

8. Once the thermostat is in pairing mode, press and quickly

release the “Connect” button on the ERM.

MCR35659

CONNECTED LED STATUS

Connect

Flashing: Device Connecting

Green: Device Connected

Red: Not Communicating

Compressor

Boiler

Connected

MCR35660

CONNECTED LED STATUS

Connect

Flashing: Device Connecting

Green: Device Connected

Red: Not Communicating

Compressor

Boiler

Connected

33-00135EFS_D.book Page 9 Friday, September 8, 2017 1:59 PM

33-00135EFS—07 10

When the ERM is connected to the system, the ERM’s “Connected” LED will be

solid green and the thermostat will show “ERM” in its Wireless Manager. (Fig.

10)

Fig. 10.

Mounting ERM

9. Use two screws and wall anchors to attach the ERM to the exte-

rior wall near the compressor. The location should be at least

3 feet above ground and oriented with the two wire exits fac-

ing downward. See Figs. 11 and 12.

10. Attach cover and secure with bottom screw (Fig. 13).

Fig. 11. Mounting orientation.

MCR35661

CONNECTED LED STATUS

Connect

Flashing: Device Connecting

Green: Device Connected

Red: Not Communicating

Compressor

Boiler

Connected

MCR35662

CONNECTED LED STATUS

Connect

Flashing: Device Connecting

Green: Device Connected

Red: Not Communicating

Compressor

Boiler

Connected

MCR35665

MOUNTING

SCREWS

CORRECT

Equipment Remote Module I ERM5000R

Compressor

Boiler

Connected

Connect

CONNECTED LED STATUS

Flashing: Device Connecting

Green: Device Connected

Red: Not Communicating

Compressor:

Jump J and R

Boiler:

Remove Jumper

JRC

TO/B

S1 S1

INCORRECTINCORRECT

Equipment Remote Module I ERM5000R

Compressor

Boiler

Connected

Connect

CONNECTED LED STATUS

Flashing: Device Connecting

Green: Device Connected

Red: Not Communicating

Compressor:

Jump J and R

Boiler:

Remove Jumper

JRC

TO/B

S1 S1

Equipment Remote Module I ERM5000R

Compressor

Boiler

Connected

Connect

CONNECTED LED STATUS

Flashing: Device Connecting

Green: Device Connected

Red: Not Communicating

Compressor:

Jump J and R

Boiler:

Remove Jumper

JRC

TO/B

S1 S1

33-00135EFS_D.book Page 10 Friday, September 8, 2017 1:59 PM

Otros manuales para REDLINK ERM5220R

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Mando a distancia de Honeywell

Honeywell

Honeywell HS3FOB1N Manual de usuario

Honeywell

Honeywell Power Presenter RF Manual de usuario

Honeywell

Honeywell 5834-4 Instrucciones de funcionamiento

Honeywell

Honeywell Wireless Remote Control Manual de usuario

Honeywell

Honeywell SILENT KNIGHT RA-2000 Manual de usuario

Honeywell

Honeywell Silent Knight 6860 Manual técnico

Honeywell

Honeywell ADEMCO 5804BDV Manual de usuario

Honeywell

Honeywell Hometronic HRD 20 Manual de instrucciones

Honeywell

Honeywell TCC800MS Manual de usuario

Honeywell

Honeywell DG115EZIAQ - TrueIAQ Digital IAQ Control Manual de usuario

Honeywell

Honeywell HVC0001 Manual de usuario

Honeywell

Honeywell 5805-6A Manual de usuario

Honeywell

Honeywell 42136 Manual de usuario

Honeywell

Honeywell TrueIAQ Manual de usuario

Honeywell

Honeywell REM5000R01 Manual de usuario

Honeywell

Honeywell TFU 22 Manual de usuario

Honeywell

Honeywell NOTIFIER LCD6000A Manual de instrucciones

Honeywell

Honeywell EXCEL 5000 OPEN ZAPP Manual de usuario

Honeywell

Honeywell FocusPRO 6000 Series Manual de usuario

Honeywell

Honeywell ADEMCO 5804BD Manual de usuario

Honeywell

Honeywell Versa-Pro UDC3000 Manual de usuario

Honeywell

Honeywell TS607 Manual de usuario

Honeywell

Honeywell ADEMCO 5804BDV-CN Manual de usuario

Honeywell

Honeywell 40015 Manual de usuario

Manuales populares de Mando a distancia de otras marcas

Panasonic

Panasonic EUR7622KB0 Manual de usuario

Bang & Olufsen

Bang & Olufsen Beo4 Manual de usuario

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manual de usuario

Multiplex

Multiplex PROFI TX 9 Manual de usuario

One Remote

One Remote RMB4 Manual de usuario

FUTABA

FUTABA 9ZAP - PART2 Manual de usuario

HR Matic

HR Matic HR MULTI 3 Manual de usuario

Yamaha

Yamaha ACC-GNRST-30-20 Manual de usuario

EisSound

EisSound KBSOUND Manual de usuario

Marantz

Marantz RC101 Manual de usuario

Conrad

Conrad FS20 TC6 Manual de usuario

Anritsu

Anritsu MP1777A Manual de usuario

Niles

Niles WVC100 Guía de solución de problemas

RCA

RCA RCU1300 Manual de usuario

Bang & Olufsen

Bang & Olufsen BEO6 Manual de usuario

GE 94901 Manual de usuario

Onbon

Onbon YQ1-75 Manual de usuario

FUTABA

FUTABA R7108SB Instrucciones de instalación