Honeywell RP2B Manual de usuario
RP2B/RP2D/RP4B/RP4D*
Thermal Printers
Quick Start Guide
RP234-EN-QS Rev C
10/18
*For China, models RP2B-C, RP2D-C, RP4B, RP4D-C
*For Thailand models RP2B, RP2D-T, RP4B, RP4D-T
1
Get Started
1. Install the battery in the printer. Align the release tab with
the same side as the charge contacts and lock the battery
into position. The latch clicks into place when properly
seated.
2. Connect the power supply to printer’s power jack.
2
3. Connect the AC power cord to the power supply and plug
into an outlet.
Do not operate the printer while it is connected to the
AC power supply.
3
Load Labels or Paper
Load labels or paper into the printer as follows:
1. Press down on the latch lock and lift up the printer’s cover.
2. Slide and hold open the supply hubs.
4
3. Orient the paper as shown and insert into the printer.
4. Allow the supply hubs to retract onto the paper roll, then
press the cover down until it latches.
5. Press the media button 2 or 3 times to normalize
tracking. Each button press advances the paper to the start
of the next label.
Download Required Software
1. Create a new folder on your local computer named Drivers.
2. Go to the Technical Support Downloads Portal at https://
hsmftp.honeywell.com.
5
3. Go to:
Software
- Printers
- Mobile - Portable
- RP2 RP3 RP4
- Utility
to download the NETira® CT Printer Configuration Utility.
4. When prompted, click on Open Honeywell Software
Downloader.
5. Once the file has been downloaded, extract it to your
Drivers folder.
6. Go to:
Software
- Printers
- Mobile - Portable
- RP2 RP3 RP4
- Drivers
- Printer
to download the Windows Printer Drivers (for DPL Input
Mode).
7. When prompted, click on Open Honeywell Software
Downloader.
8. Once the file has been downloaded, extract it to your
Drivers folder.
9. Open the Drivers folder and double-click each of the
setup.exe files. Follow the prompts to install each piece of
software.
6
Add the Printer to Your Host System
The default USB class is CDC Composite. On some systems (e.g.,
handheld devices), you will have to change this USB class in
order to connect. See your User Guide for further information.
1. Connect the USB cable to the printer and to the USB port on
the host system.
2. Power up your printer.
3. Your host computer should recognize the printer and begin
adding the device driver. If the setup operation does not
start, locate the Devices and Printers section in the Control
Panel and select Add a Printer.
4. Select the appropriate RP printer model and follow the
prompts to finish installation.
Configure the Printer
1. Turn the printer on and connect it to the computer using the
USB cable.
2. Open the NETira™CT Printer Configuration Utility Tool.
7
3. Query the printer by clicking Tools - Update Available
Connections For Printer. This will look for the USB Virtual
COM Port.
4. Once this is completed, reopen the dropdown menu and
select the USB Virtual COM port.
Note: Make sure this port is not in use by the printer driver when
you add it to the host system.
5. Press CTRL-q to display the printer’s configuration.
See your User Guide for detailed information about changing
the printer’s settings.
8
Front Panel
On/Off Button
Button Press Result
Any length press when printer is off Turn printer on
Short press (less than 5 seconds) Enter or exit sleep mode
Medium press (5 - 10 seconds) Print configuration label
Long press (more than 10 seconds) Turn printer off
On/Off
Button
Media
Button
Battery
Charge
Level Bluetooth
Indicator
WiFi
Signal
9
LED Display
Media Button
The media button advances the paper through the printer. When
there is no paper in the printer, the button blinks red.
Icon Indication
Battery
charge
level
When not charging:
Off = Battery is midway to fully charged
Solid orange = Battery charge is 10-30%
Blinking red = Battery charge is 10% or less
When charging:
Solid green = Battery charge is 90% or more
Solid red = Battery charge is less than 90%
Bluetooth
indicator
Off = Bluetooth radio is off, disabled, not associated
with a mobile device, or printer is off
Blinking = Data transmission
Solid blue = Bluetooth is enabled and connected
WiFi
signal
Off = WiFi radio is off, disabled, not associated with a
mobile device or network, or printer is off
White = WiFi is enabled and connected
Button Press Result
Short press Feeds label or paper length
Press and hold (when configured for
continuous form receipt paper)
Media feeds continuously to
the maximum label length
Otros manuales para RP2B
2
Este manual sirve para los siguientes modelos
8
Tabla de contenidos
Otros manuales de Impresora de Honeywell
Honeywell
Honeywell MP Compact4 Manual de usuario
Honeywell
Honeywell IMPACT IHR810 Manual de usuario
Honeywell
Honeywell PC42T Manual de usuario
Honeywell
Honeywell PC42d Manual de usuario
Honeywell
Honeywell E-Class MK IIIA Manual de usuario
Honeywell
Honeywell PC42T Manual de usuario
Honeywell
Honeywell MP Compact Mark III Manual de usuario
Honeywell
Honeywell 6824 Manual de usuario
Honeywell
Honeywell PM42 Manual de usuario
Honeywell
Honeywell CN51 PrintPAD Manual de usuario
Honeywell
Honeywell PC43K Manual de usuario
Honeywell
Honeywell CN51 PrintPAD Manual de usuario
Honeywell
Honeywell PC42T Manual de usuario
Honeywell
Honeywell PC42T Manual de usuario
Honeywell
Honeywell PRU0901 Manual de usuario
Honeywell
Honeywell PD45 Manual de usuario
Honeywell
Honeywell PC43K Manual de usuario
Honeywell
Honeywell Intermec PD43 Manual de usuario
Honeywell
Honeywell 6824 Manual de usuario
Honeywell
Honeywell PC45 Series Manual de usuario
