Honeywell HLSPS25-XPH Manual de usuario

Power Supply Unit

HLS PS Series

HLSPS25-XPH and HLSPS50-XPH

User manual

Information in this document is subject to change without notice

8 APRIL 2010

HW_MN-DT-1305I_B

HLS PS25 & HLS PS50 User Manual

MN-DT-1305I_B 2

HLS PS25 & HLS PS50 User Manual

MN-DT-1305I_B 3

Contents

1 HLS PS Series Installation 4

1.1 Checking the HLS PS for damage 4

1.2 Pre-installation check list 5

1.3 Transient protection 5

1.4 Cleaning 5

1.5 Back Box HLS PS fixing 6

2 Functions and indicators 7

2.1 HLS PS25 and HLS PS50 characteristics 8

2.2 Battery 9

2.3 Fault relay 9

2.4 Control Unit connections 10

2.5 Indicator leds 12

3 Specification 14

HLS PS25 & HLS PS50 User Manual

MN-DT-1305I_B 4

1. POWER SUPPLIES HLS PS SERIES

INSTALLATION

The HLS PS Serie s i s ea sy to i nstall p roviding th e

recommended procedu res de scribed in this m anual are

followed.

Follow all installation instructions described in this

manual. Theses instructions must be understood

and followed to avoid damage to the S Series and

associated equipment.

1.1 Checking the HLS PS Series for

damage

Before attempting to install your power supply you should

do the following.

The procedure describe bellow tells you what to do in the

unlikely event that the sup plied e quipment ha s been

damaged after leaving th e factory. Ho wever, if you have

problems re garding th e quality of a ny sup plied order

items, follow the procedure bellow:

1. If, after removing the HLS PS Series , a visual

inspection reveals that it has bee n damaged, you MUST

NOT continue with the installation but conta ct you

supplier for advice on what to do next.

Similarly, if the prod uct is found to be faulty during

installation, contact your supplier immediately.

2. To aid you r supplier, you are requested to note all the

details relevant to your complaint, clearly stating details of

any techni cal probl ems, date of recei pt, packaging

condition, etc. and forward this to your supplier.

3. Wh ere th e p roduct needs to be returned to your

supplier, you are requested to use the original packaging

wherever possible

• The b uilding whe re th e device i s connected should

have su rge and earth protections an d these sh ould be

easily a ccessible in o rder to di sconnect the unit from

mains by its two poles.

WARNING

HLS PS25 & HLS PS50 User Manual

MN-DT-1305I_B 5

1.2 Pre-installation check list

Before selecting the location for the HLS PS Series, DO make

sure that:

a) The ambient temperature is in the range:

-5 ºC to 40 ºC

b) The relative humidity is bellow:

93% (non-condensing)

c) DO NOT loca te th e e quipment w here i t is ex posed to high

levels of moisture.

d) DO NO T locate the e quipment where there are hi gh levels of

vibration or shock.

e) DO NOT s ite the HLS PS Series where there w ould be

restricted access to the internal equ ipment and wiring

connections.

1.3 Transient protection

As with all solid state devices, this system may operate erratically

or c an be damaged i f sub jected to li ghtning-induced t ransients.

This equipmen t contains trans ient p rotection devic es. Al though

no system is immune from lightning transients an d in terference,

for thes e devices to func tion co rrectly, and to reduc e

susceptibility, this equipment must be earthed correctly.

The use of overhead or outside aerial wiring is not recommended

due to the increased susceptibility to nearby lightning strikes.

The HLS PS Series is wall m ounted in a posi tion, which a llows

clear v isibility of ind icator leds. The he ight above fl oor le vel

should be chosen such that t he indicators are just above normal

eye level (approximately 1.5 metres).

1.4 Cleaning

The HLS PS Series cas e may be clean ed periodically by wiping

with a soft, damp lint-free cloth.

Do not use solvents.

HLS PS25 & HLS PS50 User Manual

MN-DT-1305I_B 6

1.5 Back Box HLS PS Series fixing

When a suitable location has been found for installing the HLS PS Series, proceed as follows:

1. Hold th e b ack box a ssembly in the required p osition ag ainst the wall and m ark the p osition of th e

fixing holes, while ensuring the panel is level.

The drawing below shows the position of the fixing holes at the back box.

Do NOT use the back box as a guide when drilling!

2. Drill and plug the wall.

3. Prepare apertures required for cable access.

4. Screw the ba ck box to the wall using the fixing hole s

and appropriate-sized screws.

HLS PS25 & HLS PS50 User Manual

MN-DT-1305I_B 7

2. HLS PS Functions and indicators

FRONT PANEL:

FUS BAT FAULT LOW BAT NO BAT BAT TEST BAT CH BAT DIS IN ALARM 321087

CPU

MAX.

LEGEND:

=> ON

=> FAULT

=> MAIN SUPPLY FAULT

=> BATTERY FAULT

=> BATTERY CHARGER

FAULT

=> OUTPUT 1 FAULT

=> OUTPUT 2 FAULT

=> EARTH FAULT

=> OVERLOAD

=> SYSTEM FAULT

INTERNAL LEDS:

HLS PS25 & HLS PS50 User Manual

MN-DT-1305I_B 8

2.1 HLS PS25 / HLS PS50 characteristics

These Po wer Supplies Units are des igned to comply with th e

requirements of EN54-4 in order to provide fire control systems with

backup supply.

The HLS PS Series operates at 115/230 Vac and 50/60 Hz.

Both Power Supply Units, HLS PS25 a nd HLS PS50, are very similar :

they consist o f a 2x 65W, which means 1 30W in HL S PS50 and 1 x65W

in HLS PS25 and a standard module control which supervises the entire

power supply.

HLS PS25 an d HLS PS50 power supplie s provide 2.5 Amp and 5 Amp

respectively a nd 300mA to 600mA of th em are dedic ated to charg e

batteries. Th ese po wer su pplies are able to supply either up to 1.1 0

and 2.20 Amp current at each PSO1 a nd PSO2 out puts. This is the

default set up (DIP SW1 ON, up position). However, power supplies can

also supply all the current in only one outp ut by placing the DIP SW1 in

the down position, OFF. This way, all the current (2.20Amp or 4.40Amp

respectively) will be supplied through PSO1 output

HLS PS25

HLS PS50

SW1 up

SW1 down

HLS PS25 & HLS PS50 User Manual

MN-DT-1305I_B 9

2.2 Battery

DIP SW2 al lows se lecting the m aximum cu rrent o f battery load,

depending on the batteries inside the power supply unit box.

With DIP SW2 in ON position (up), 7Amp/h batteries can be charged

at 3 00mA. When DIP SW2 is in OFF pos ition (down ), 20Amp/h

batteries can be charged at 600mA.

In this ex ample,

DIP

SW2

is in OFF position

(down) and the l oad current will be limited to

600mA.

DIP SW3

. This DIP switch is in ON position (up).

For future use.

DIP SW4

. For future use.

2.3 Fault relay

The Power Supply has a fault relay to repo rt any anomaly to a remote

control unit.

Any fault has a delay of 30 seconds from the fault signal to fault relay

confirmation, ex cept when there is a ma ins AC loss, which will be

indicated afte r an 8-minut e delay to avoid faults from intermittent

power cuts.

In stand-by, the fault relay is energized indicating its normal operation.

In case of any fault, the relay deactivates after the confirmation time.

Fault relay operation

FAULT

switch with three terminals

Terminal 1 (left) C common

Terminal 2 (centre) NC or Normally Closed

Terminal 3 (right) NO or Normally Open

Fault relay operates as follows:

No supervision (without power) or in fault condition

Between C and NC —> continuity

Between C and NO —> open circuit

Operating with supervision without faults, i.e. in NORMAL STATE

Between C and NC —> open circuit

Between C and NO —> continuity

HLS PS25 & HLS PS50 User Manual

MN-DT-1305I_B 10

2.4 Control Unit Connections:

The following

connectors are placed at the top of the Control Unit:

FAULT

(NC) Normally Closed Contact

FAULT

(NO) Normally Open Contact

The faul t rel ay may be li nked to an analogue

input modu le to report any fault t o a third

equipment li ke a FACP ( Fire Alarm Control

Panel).

IN ALARM

(+)

IN ALARM

(-)

Alarm input to d isable, momen tarily, t he battery c harger and be able to supp ly 300 -

600mA from ba ttery loa d to the ou tputs. Fo r th is, i t is necessa ry to l ink both IN

ALARM terminals by means of a jumper or short-circuit.

When this input is activated, the control unit will have an extra current of battery load

0.3 A or 0.6 A, depending on the DIP SW2 for outputs. Thus, if the power supply is in

Overload (Imax) sta te, the indication will disappear by ac tivating this input, p rovided

that the excess current is the current which is supplying batteries.

PSO1

Output 1 (+)

PSO1

Output 1 (-)

PSO2

Output 2 (+)

PSO2

Output 2 (-)

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Fuente de alimentación de Honeywell

Honeywell

Honeywell HPF24S8 Manual técnico

Honeywell

Honeywell 9007AX01 Manual de usuario

Honeywell

Honeywell Notifier PSU7A Manual de usuario

Honeywell

Honeywell HP400ULM Manual técnico

Honeywell

Honeywell HPTV2416UL Manual técnico

Honeywell

Honeywell HPR2416CBUL Manual de usuario

Honeywell

Honeywell 900P01 Manual de uso y cuidado

Honeywell

Honeywell GENT VCS-PSU-N Manual de usuario

Honeywell

Honeywell HPF24S8 Manual de usuario

Honeywell

Honeywell 208414 Manual de usuario

Honeywell

Honeywell HPTV2408UL Manual técnico

Honeywell

Honeywell PRO32E1PS Manual de instrucciones

Honeywell

Honeywell NOTIFIER ALI50EN Manual de usuario

Honeywell

Honeywell HPR12DC416UL Manual técnico

Honeywell

Honeywell PS-HL-138 BM Series Manual de usuario

Honeywell

Honeywell HPTV2404 Manual técnico

Honeywell

Honeywell HP1205UL-4 Manual técnico

Honeywell

Honeywell VX89301PWRSPLY Manual de usuario

Honeywell

Honeywell NOTIFIER APS2-6R/E Manual de usuario

Honeywell

Honeywell HP300ULM Manual técnico

Honeywell

Honeywell HPL624 Manual técnico

Honeywell

Honeywell PS1202A00 Manual de usuario

Honeywell

Honeywell SILENT KNIGHT SK-PS6 Manual de usuario

Honeywell

Honeywell NOTIFIER FCPS-24S6 Manual de usuario

Manuales populares de Fuente de alimentación de otras marcas

Monacor

Monacor PS-12CCD Manual de usuario

VOLTIMA

VOLTIMA MagicBox 15 Manual de usuario

Agilent Technologies

Agilent Technologies 6032A Manual de usuario

Miller

Miller Auto Deltaweld 452 Manual de usuario

BCP

BCP PUOUBK Hoja de instrucciones

HC 2210 Manual de usuario

Puls

Puls CT5.241 Manual de usuario

OCZ

OCZ ZX1250W Manual de usuario

iseg

iseg ECH 238 Manual de usuario

Power

Power XXL A Series Manual de usuario

Agilent Technologies

Agilent Technologies 6631B Manual de usuario

Renogy

Renogy PHOENIX 300 Manual de usuario

HP 6200B Manual de servicio

Epson

Epson Stylus Scan 2500 Manual de funcionamiento

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manual de usuario

Puls

Puls MiniLine ML50.100 Manual de usuario

Puls

Puls AS-Interface SLA4.100 Manual de usuario

Kenwood

Kenwood PS-60 Manual de usuario