Honeywell HEN04112 Manual de usuario

Document 800-21090V2 – Rev A – 03/2016

User Guide

Performance Series Full PoE

Network Video Recorder

HEN04112 HEN08112 HEN16122

HEN04122 HEN08122 HEN16142

HEN04102 HEN08142 HEN16162

HEN08102 HEN16102

User Guide

Revisions

Issue Date Revisions

A 09/2015 New document based on 800-18160V2.

V1 Rev A 10/2015 Added two notes in the Camera Configuration chapter.

V2 Rev A 03/2016 Amended the part numbers. Amended the product description. Added the Smart

Search section in the Playing Back Video section. Amended some Specifications.

Added the appendix about MAXPRO Cloud. Added the list of symbols in the

Cautions/Safety/Regulatory chapter.

| 5

800-21090V2 - A - 03/2016

Cautions and Warnings

Installation and servicing should be performed only by qualified and experienced technicians to conform to all local

codes and to maintain your warranty.

WARNING

Use only with the supplied power converters. The Ethernet

connection is not intended to be connected to an exposed (outside plant) network.

CAUTION There is a risk of explosion if the battery is replaced by an incorrect type.

Dispose of used batteries in accordance to local laws.

CAUTION Installation and servicing should be performed only by qualified and

experienced technicians to conform to all local codes and to maintain your warranty.

Regulatory Statements

FCC Compliance Statement

Information to the User: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation.

www.honeywell.com/security

6 | Performance Series Full PoE Network Video Recorder User Guide

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Note Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada.

Manufacturer’s Declaration of Conformance

North America

The equipment supplied with this guide conforms to UL 60950-1 and CSA C22.2 No. 60950-1.

Europe

The manufacturer declares that the equipment supplied is compliant with the essential protection requirements of the

EMC directive 2004/108/EC and the Low Voltage Directive (LVD) 2006/95/EC, conforming to the requirements of

standards EN 55022 for emissions, EN 50130-4 for immunity, and EN 60950 for electrical equipment safety.

Waste Electrical and Electronic Equipment (WEEE)

Correct Disposal of this Product (applicable in the European Union and other

European countries with separate collection systems).

This product should be disposed of, at the end of its useful life, as per applicable

local laws, regulations, and procedures.

| 7

800-21090V2 - A - 03/2016

Safety Instructions

BEFORE OPERATING OR INSTALLING THE UNIT, READ AND FOLLOW ALL INSTRUCTIONS.

AFTER INSTALLATION, retain the safety and operating instructions for future reference

1. HEED WARNINGS - Adhere to all warnings on the unit and in the operating instructions.

2. INSTALLATION

• Install in accordance with the manufacturer’s instructions.

• Installation and servicing should be performed only by qualified and experienced technicians to conform to

all local codes and to maintain your warranty.

• Do not install the unit in an extremely hot or humid location, or in a place subject to dust or mechanical

vibration. The unit is not designed to be waterproof. Exposure to rain or water may damage the unit.

• Any wall or ceiling mounting of the product should follow the manufacturer’s instructions and use a

mounting kit approved or recommended by the manufacturer.

3. POWER SOURCES - This product should be operated only from the type of power source indicated on the

marking label. If you are not sure of the type of power supplied to your facility, consult your product dealer or

local power company.

4. HEAT - Situate away from items that produce heat or are heat sources such as radiators, heat registers, stoves,

or other products (including amplifiers).

5. WATER AND MOISTURE - Do not use this unit near water or in an unprotected outdoor installation, or any area

classified as a wet location.

6. MOUNTING SYSTEM - Use only with a mounting system recommended by the manufacturer, or sold with the

product.

7. ATTACHMENTS - Do not use attachments not recommended by the product manufacturer as they may result in

the risk of fire, electric shock, or injury to persons.

8. ACCESSORIES - Only use accessories specified by the manufacturer.

9. CLEANING - Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

10. SERVICING - Do not attempt to service this unit yourself as opening or removing covers may expose you to

dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

11. REPLACEMENT PARTS - When replacement parts are required, be sure the service technician has used

replacement parts specified by the manufacturer or have the same characteristics as the original part.

Unauthorized substitutions may result in fire, electric shock or other hazards.

Warranty and Service

Subject to the terms and conditions listed on the Product warranty, during the warranty period Honeywell will repair or

replace, at its sole option, free of charge, any defective products returned prepaid.

In the event you have a problem with any Honeywell product, please call Customer Service at 1.800.323.4576 for

assistance or to request a Return Merchandise Authorization (RMA) number.

www.honeywell.com/security

8 | Performance Series Full PoE Network Video Recorder User Guide

Be sure to have the model number, serial number, and the nature of the problem available for the technical service

representative.

Prior authorization must be obtained for all returns, exchanges, or credits. Items shipped to Honeywell without a

clearly identified Return Merchandise Authorization (RMA) number may be refused.

List of Symbols

The following is a list of symbols that might appear on the NVR.

Table 1-1 List of Symbols

Symbol Explanation

The WEEE symbol.

This symbol indicates that when the end-user wishes to

discard this product, it must be sent to separate collection

facilities for recovery and recycling. By separating this product

from other household-type waste, the volume of waste sent to

incinerators or landfills will be reduced, and thus natural

resources will be conserved.

The UL compliance logo.

This logo indicates that the product has been tested and is

listed by the Underwriters Laboratories.

The FCC compliance logo.

This logo indicates that the product conforms to Federal

Communication’s Commission compliance standards.

The direct current symbol.

This symbol indicates that the power input/output for the

product is direct current.

The alternating current symbol.

This symbol indicates that the power input/output for the

product is alternating current.

The LDPE symbol.

This symbol indicates that this product is made of

Low-Density Polyethylene (LDPE).

The Direct Current symbol.

This symbol indicates that the product operates from a 12 V

direct current.

| 9

800-21090V2 - A - 03/2016

The Lead-free symbol.

This symbol indicates that the product does not contain lead

(Pb).

The CCC compliance logo.

This logo indicates that the product conforms with the China

Compulsory Certification guidelines.

The Environment Friendly Use-period symbol.

This symbol indicates the length of time that this electronic

product can used without harming the environment.

The RCM Compliance symbol.

This symbol indicates that the product conforms with the

Australian RCM guidelines.

The TVU Lab symbol.

This symbol indicates that the product has been safety tested

by the TUV Lab.

The Direct Current symbol.

This Direct Current symbol indicates that the product operates

direct current.

This symbol indicates that the product is to be used indoors.

The CE Compliance logo.

This logo indicates that the product conforms to the relevant

guidelines/standards for the European Union harmonization

legislation.

The Protective Earth symbol.

This symbol indicates that the marked terminal is intended for

connection to the protective earth/grounding conductor.

Table 1-1 List of Symbols

Symbol Explanation

www.honeywell.com/security

10 | Performance Series Full PoE Network Video Recorder User Guide

This symbol is used to direct attention to important

information.

This symbol warns that the corresponding action could result

in an electric shock.

This symbol indicates On/Standby functionality of the

corresponding control/button/switch.

Table 1-1 List of Symbols

Symbol Explanation

Otros manuales para HEN04112

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Honeywell

Honeywell

Honeywell QA 10 DN 25 G I Manual de usuario

Honeywell

Honeywell EWA600C-RF55C Manual de usuario

Honeywell

Honeywell IAQPoint2 Manual de usuario

Honeywell

Honeywell SLN 700 Manual de instrucciones

Honeywell

Honeywell SM-RI-X Manual de usuario

Honeywell

Honeywell Class 320 Meter Manual de usuario

Honeywell

Honeywell NK Manual de usuario

Honeywell

Honeywell RMA 3000 Manual de usuario

Honeywell

Honeywell Sensepoint XCL Manual de usuario

Honeywell

Honeywell A700 Manual de usuario

Honeywell

Honeywell BK V2 Manual de usuario

Honeywell

Honeywell MI Wireless Guía de inicio rápido

Honeywell

Honeywell 3400 Manual de usuario

Honeywell

Honeywell ERX 350 Manual de usuario

Honeywell

Honeywell GENT S4-34 Series Manual de instrucciones

Honeywell

Honeywell 04973 Series Manual

Honeywell

Honeywell 90DM4 Manual de usuario

Honeywell

Honeywell HTRAM-V1-W Manual de usuario

Honeywell

Honeywell QX Series Manual de usuario

Honeywell

Honeywell RAE Systems NeutronRAE II Manual de usuario

Honeywell

Honeywell HERMetic PRESS Manual de operación

Honeywell

Honeywell DR4300 Series Guía

Honeywell

Honeywell DPR180 Manual de usuario

Honeywell

Honeywell Minitrend Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario