Honeywell Bendix/King KN 63 Manual de usuario

INSTALLATION MANUAL

KN 63

DISTANCE MEASURING

EQUIPMENT

MANUAL NUMBER 006-00176-0004

REVISION 4 October, 2004

WARNING

Prior the export of this document, review for export license requirement is needed.

REPRODUCTION OF THIS PUBLICATION OR ANY PORTION THEREOF BY ANY MEANS

WITHOUT THE EXPRESS WRITTEN PERMISSION OF HONEYWELL IS PROHIBITED,

EXCEPT TO THE EXTENT REQUIRED FOR INSTALLATION OR MAINTENANCE OF THE

RECIPIENT'S EQUIPMENT. FOR FURTHER INFORMATION CONTACT THE MANAGER,

TECHNICAL PUBLICATIONS, HONEYWELL, ONE TECHNOLOGY CENTER, 23500 WEST

105TH STREET OLATHE KS 66061 TELEPHONE: (913) 782-0400.

BENDIX/KING KN 63

Rev 4, October/2004 00176I04.TDC Page R-1

REVISION HISTORY

KN 63 Installation Manual

Part Number: 006-00176-0004

For each revision, Add, delete or replace pages as indicated.

REVISION: 4, October, 2004

ITEM ACTION

All pages Remove and Replace

BENDIX/KING KN 63

Rev 4, October/2004 00176I04.TDC Page R-2

THIS PAGE RESERVED

BENDIX/KING KN 63

Rev 4, October/2004 00176I04.TDC Page TOC-1

TABLE OF CONTENTS

SECTION I

GENERAL INFORMATION

Paragraph Page

1.1 Introduction ..................................................................................................1-1

1.2 Description of Equipment .............................................................................1-1

1.3 Technical Characteristics .............................................................................1-1

1.4 Units and Accessories..................................................................................1-4

1.5 License Requirements .................................................................................1-5

SECTION II

INSTALLATION

2.1 General Information .....................................................................................2-1

2.2 Unpacking and Inspecting Equipment..........................................................2-1

2.3 Equipment Installation..................................................................................2-1

2.3.1 KN 63 Installation .........................................................................................2-1

2.3.2 Molex Connector Assembly..........................................................................2-2

2.3.3 KDI 572/KDI 573/KDI 574 Installation..........................................................2-3

2.3.4 DME Antenna Installation.............................................................................2-4

SECTION III

OPERATION

3.1 General ........................................................................................................3-1

LIST OF ILLUSTRATIONS

Figure Page

2-1 KN 63 Outline and Mounting Drawing..........................................................2-7

2-2 Molex Terminals and Tools (3 sheets)..........................................................2-9

2-3 KDI 572/573/574 Installation and Mounting Drawing ...................................2-13

2-4 Connector Pin Location Guide .....................................................................2-15

2-5 Antenna Installation Drawing .......................................................................2-17

2-6 EFIS 40/50 _ KDI 574 Interconnect .............................................................2-19

2-7 KA 61 Installation Drawing ...........................................................................2-21

2-8 030-00005-0000 Connector Assembly.........................................................2-25

2-9 KN 63/KDI 572/573 Interconnect .................................................................2-27

2-10 KN 63/KDI 572/KDI 573/KX 165 Interconnect..............................................2-29

2-11 KN 63/KDI 573/KDI 574 ...............................................................................2-33

2-12 KDI 572/KN 63 to Narco 122 Interconnect...................................................2-35

3-1 KDI 572 with Label .......................................................................................3-2

3-2 KDI 573 with Label .......................................................................................3-3

TABLES

Ta b le Page

1-1 Technical Characteristics .............................................................................1-1

1-2 DME Channeling Codes...............................................................................1-3

1-3 KN 63 Installation Kit....................................................................................1-4

BENDIX/KING KN 63

Rev 4, October/2004 00176I04.TDC Page TOC-2

BENDIX/KING KN 63

Rev 4, October/2004 00176I04.TDC Page 1-1

SECTION I

General Information

1.1 INTRODUCTION

This manual contains information relative to the physical, mechanical, and electrical characteris-

tics and installation procedures for the KN 63 DME, KDI 572/574 Master Indicators, and KDI 573

Slave Indicator.

1.2 DESCRIPTION OF EQUIPMENT

The KN 63 is a remote mounted, 200 channel TSO'd DME employing the latest state of the art

solid-state transmitter and large scale integrated circuit (LSI) technology. All tuning is done elec-

tronically; using a single crystal, digital, frequency synthesizer. Range, speed, and time-to-station

are measured digitally, using two LSI's. Another LSI is employed in the digital frequency synthe-

sizer. The KN 63 can be operated with any DC input from 11 to 33 volts. Power consumption is

17 watts maximum with two indicators at any input voltage.

The KN 63 is designed to operate with the panel mounted KDI 572/574 master indicators (re-

quired) and the KDI 573 slave indicator (optional). Both indicators have a gas discharge display

that simultaneously indicates range, speed, and time-to-station. An automatic dimming circuit ad-

justs the brightness of the display to compensate for changes in ambient light level. Both indica-

tors contain an LSI. The KDI 572/574 master indicator accepts channeling data from either of two

external NAV control heads. A rotary switch on the KDI 572 selects N1, hold, or N2 channeling

and also provides a system power switch. The KDI 572/574 will accept shifted BCD, ARINC 2X5,

or slip code tuning. It converts whatever code is received into digital serial data which is sent to

the KN 63. Both indicators receive DME range, speed, and time-to-station as digital serial data

from the KN 63. The KDI 573 slave indicator has no mode switch and merely provides a duplicate

display of the information shown on the KDI 572.

1.3 TECHNICAL CHARACTERISTICS

SPECIFICATION CHARACTERISTIC

TSO Compliance (KN 63, KDI 572, KDI 573 & KDI 574) FAA TSO C66a

(KA 60 ANTENNA) FAA TSO C66a & TSO C74c

(KA 61 Antenna) FAA TSO C66c, C74c, C112, C118,

C147

RTCA DO-160 Environmental

Categories

KN 63: /A2D2/A/MN/XXXXXXZAAAA

KDI 572, KDI 573 & KDI 574: /A1D1/A/KPS/

XXXXXXZAAAA

KA 60 Antenna: /D2/A/JY/XXXXXXXXXXX

RTCA DO-160D Environmental Categories KA 61: [D2X]ACB[SCMYL,RG]XRFXX-

SXXXXXXX[XXXX][2A]AX

Channels 200 channels

Electrical a. All solid state transmitter

b. Electronically tuned by single crystal, digital,

frequency synthesizer.

c. Range, speed, and time-to-station measured

digitally, using large scale integrated circuits

d. Gas discharge display

BENDIX/KING KN 63

Rev 4, October/2004 00176I04.TDC Page 1-2

*The maximum range at which the DME will lock up is determined by altitude and ground station

output power and sensitivity.

**The KDI 572 and KDI 573 do not require power from the aircraft power buss.

TABLE 1-1 TECHNICAL CHARACTERISTICS

SPECIFICATION CHARACTERISTIC

Output Power 50 watts peak pulsed power minimum, 100 watts nom-

inal

Maximum Display Range* 389 nautical miles

Aquisition Sensitivity -82dBm minimum, -87dBm nominal

Range Accuracy* ±.1 nautical miles or ±.14%, whichever is greater from

0 to 99.9 nautical miles. ±1 nautical mile from 100 to

389 nautical miles.

Ground Speed Accuracy ±1 knot or ±1%, whichever is greater from 0 to 999

knots.

Time-to-Station Accuracy ±1 minute from 0 to 99 minutes

Search Time 1.0 second nominal

Memory Time 11 to 15 seconds

Audio Output (Ident) Level adjustable up to 15mw into 500 ohm load, nomi-

nally set for 2mw.

Maximum altitude 50,000 feet

KN 63 Dimensions and Weight

(Including mounting rack and

connectors)

Length: 11.550 inches (29.34 cm)

Width: 1.18 inches (3.00 cm)

Height: 6.50 inches (16.51 cm)

Weight: 2.8 lbs (1.27kg)

KDI 572, KDI 573 and KDI 574

Dimensions and Weight

(Including connector)

Length behind panel: 8.35 inches (21.21cm)

Width: 3.50 inches (8.89 cm)

Height: 1.35 inches (3.43 cm)

Weight: .8 lbs (.363 kg) KDI 572

Weight: .7 lbs (.318 kg) KDI 573

Power Requirements (KN 63)** 11-33VDC at 17 watts maximum with two

indicators

Channeling Sources a. External control head providing shifted BCD code

such as KFS 560B.

b. External control head providing ARINC 2X5 code

such as KX 170 and KFS 560B.

c. External control head providing slip code such as

KX 170A, KX 170B, KX 175A, and KX 175B.

KDI 572 Lighting 066-1069-00 - .065 amps at 28V or .13 amps at 14V

066-1069-01 - .23 amps at 5V

BENDIX/KING KN 63

Rev 4, October/2004 00176I04.TDC Page 1-3

0 = Connected to Remote Control Common

1 = Open

TABLE 1-2 DME CHANNELING CODES

SHIFTED BCD 2 x 5 SLIP

Frequency

MHz M8 M4 M2 M1 MA ME MC MD M0 M1 M2 M3

108 0 0 0 0 0 1 1 0 1 1 0 1

109 0 0 0 1 0 0 1 1 1 1 1 0

110 0 0 1 0 1 0 1 1 0 1 1 1

111 0 0 1 1 0 1 1 1 0 0 1 1

112 0 1 0 0 0 1 0 1 0 0 0 1

113 0 1 0 1 1 1 0 1 1 0 0 0

114 0 1 1 0 1 1 1 0 0 1 0 0

115 0 1 1 1 1 1 0 0 1 0 1 0

116 1 0 0 0 1 0 0 1 0 1 0 1

117 1 0 0 1 1 0 1 0 0 0 1 0

K800 K400 K200 K100 KA KE KC KD K0 K1 K2 K3

.0X 0 0 0 0 1 0 1 1 0 0 1 1

.1X 0 0 0 1 0 1 1 1 0 0 0 1

.2X 0 0 1 0 0 1 0 1 0 0 0 0

.3X 0 0 1 1 1 1 0 1 1 0 0 0

.4X 0 1 0 0 1 1 1 0 1 1 0 0

.5X 0 1 0 1 1 1 0 0 0 1 1 0

.6X 0 1 1 0 1 0 0 1 1 0 1 1

.7X 0 1 1 1 1 0 1 0 1 1 0 1

.8X 1 0 0 0 0 1 1 0 1 1 1 0

.9X 1 0 0 1 0 0 1 1 0 1 1 1

K50 K50 K50

.X0 111

.X5 000

BENDIX/KING KN 63

Rev 4, October/2004 00176I04.TDC Page 1-4

1.4 UNITS AND ACCESSORIES

A complete DME installation requires a KN 63 DME (066-1070-00/01), a KDI 572 masterindicator

(066-1069-00 or 01) or KDI 574 Master Indicator (066-1069-04), a KA 60/61 antenna, and one or

two external control heads (see section 1.3,channeling sources). The KDI 572 is available with

either 14/28 volt lighting (066-1069-00) or 5 volt lighting (066-1069-01). Use of the KDI 573 slave

indicator (066-1069-02) is optional. A KN 63 installation kit (050-01766-0000) and KDI 572 instal-

lation kit (050-01740-0000) are required. A KDI 573 installation kit (050-01740-0001) is needed if

a KDI 573 is used. A KDI 574 installation kit (050-01740-0002) is needed if a KDI 574 is used.

KN 63 Installation Kit (050-01766-0000)

TABLE 1-3 KN 63 INSTALLATION KIT

KDI 572: Installation Kit (050-01740-0000)

KDI 573: Installation Kit (050-01740-0001)

KDI 574: Installation Kit (050-01740-0002)

PART NUMBER DESCRIPTION QTY

030-00005-0000 CONN BNC TED 4-10-4 2

030-01094-0056 CONN MOLEX (24P) 1

030-01107-0015 CONN PINS (15) 1

047-04218-0001 HOLD DOWN BAR 2

047-04219-0001 MOUNTING RACK 1

075-00021-0001 HOLD DOWN CLAMP 1

078-00054-0000 COMPRESSION SPRING 1

088-00752-0000 CONN HOOD 1

089-02015-0037 NUT HEX 8-32 4

089-05442-0010 SCR 8-32 FHP 4

089-05529-0032 SCR FHP 1

089-05909-0007 SCR 8-32 PHP 4

089-06541-0000 SCR 4-40 PHP 2

089-08111-0034 WASHER SL #8 5

091-00109-0001 CABLE TIE 1

QTY.

Tabla de contenidos

Otros manuales de Instrumento de medición de Honeywell

Honeywell

Honeywell NK Manual de usuario

Honeywell

Honeywell AirAlert 96d Manual

Honeywell

Honeywell Enraf FlexLine RMA805 Manual de usuario

Honeywell

Honeywell Enraf FlexLine RMA805 Manual de instrucciones

Honeywell

Honeywell Sensepoint XCD RTD Manual de usuario

Honeywell

Honeywell VERTEX C Manual de usuario

Honeywell

Honeywell Q209E Modutrol IV Manual de usuario

Honeywell

Honeywell BW RigRat Manual de usuario

Honeywell

Honeywell eZtrend GR Series Manual de usuario

Honeywell

Honeywell RM640 Manual de usuario

Honeywell

Honeywell SmartLine SLG 700 Manual de usuario

Honeywell

Honeywell MI Wireless Guía de inicio rápido

Honeywell

Honeywell QA 10 DN 25 G I Manual de usuario

Honeywell

Honeywell S7751A Manual de operación

Honeywell

Honeywell C7355B Manual de usuario

Honeywell

Honeywell E-Mon Class 6200 Manual de usuario

Honeywell

Honeywell FlexLine SmartServo 954 Manual de usuario

Honeywell

Honeywell enCore Series Manual de usuario

Honeywell

Honeywell E-Mon KWH Manual de usuario

Honeywell

Honeywell BW RigRat Manual de usuario

Honeywell

Honeywell Themis alpha EI2 Instrucciones de funcionamiento

Honeywell

Honeywell TMS 9250 Manual de usuario

Honeywell

Honeywell HomMed Genesis Touch Manual de usuario

Honeywell

Honeywell MicroMAX Pro Instrucciones de funcionamiento

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario