Honeywell HNDR-S 4848 Manual de instrucciones
HONEYWELL SECURITY TECHNICAL BULLETIN 11 December 2008
www.asia.security.honeywell.com Rev 1.0 1 of 5
Honeywell Video Systems
Subject: Control HNDR-S 4848 DVR by VideoBlox HEGS5BLX
Introduction
This document describes the Protocol Interface Translator (PIT) operation specific to the Honeywell HNDR-S
series DVR. For further details on the PIT, please refer to the PIT User manual. For further details on the DVR,
please refer to the appropriate Honeywell HNDR-S DVR manual.
Quick Start Switch Settings
Output
Protocol S1/8 S1/7 S1/6 S1/5 S1/4 S1/3 S1/2 S1/1
Valid
Function Valid
Function Valid
Function Valid
Function
ASCII
string
mode
ASCII
string
mode
ASCII
string
mode
ASCII
string
mode
Off Off Off Off On On On On
Address S2/8 S2/7 S2/6 S2/5 S2/4 S2/3 S2/2 S2/1
Switch
Legend Address
7 Address
6 Address
5 Address
4 Address
3 Address
2 Address
1 Address
0
0 (B/cast) Off Off Off Off Off Off Off Off
Input
Protocol S3/8 S3/7 S3/6 S3/5 S3/4 S3/3 S3/2 S3/1
Slave Port
Baud
Slave
Port
Baud
Master
Port Baud Master
Port Baud Input
Type Input
Type Input
Type Input
Type
Bossware On Off On Off On On On Off
The above setting set the PIT as follows:
Receive Betatech compatible Bossware control messages on the RS422 slave port of the PIT at 19.2K baud.
The PIT unit address (S2/1 - S2/8 to OFF position) is set to broadcast, so all addresses will be translated. If
want to control specific unit of DVR, set the dip switch S2/1 – S2/8 of PIT address and add PIT per DVR. (It is
tested the address from 1 to 128.)
Unit ID S2/8 S2/7 S2/6 S2/5 S2/4 S2/3 S2/2 S2/1
1 Off Off Off Off Off Off Off On
2 Off Off Off Off Off Off On Off
3 Off Off Off Off Off Off On On
4 Off Off Off Off Off On Off Off
5 Off Off Off Off Off On Off On
:
255 On On On On On On On On
Transmit Honeywell HNDR-S control messages on the RS422 master port at 9600 baud, 8, N, 1 .
Note: To control HNDR-S series DVR, the DVR firmware should be 1.0.17 or later.
(Tested firmware: HVBCPUX – 4.96x HVBCFG – 3.08 (Build 32) HVBPIT44 – 3.03)
HONEYWELL SECURITY TECHNICAL BULLETIN 11 December 2008
www.asia.security.honeywell.com Rev 1.0 2 of 5
Hardware Configuration
•Connect CPU RS422 Master Port to Slave Port of HVBPIT44.
•Connect Master Port of HVBPIT44 to HNDR-S Com 2 (RS-485).
Pin Number CPU RS422 Master Port
(DB9 Female) HVBPIT44 Slave Port
(DB9 Female)
1 Tx- Rx-
2 Tx+ Rx+
3 Rx+ Tx+
4 Rx- Tx-
5 Signal Gnd Signal Gnd
6 +12V source +12V input
7 NC NC
8 NC NC
9 Ground Ground
Pin Number HVBPIT44 Master Port
(DB9 Female) HRHD-S Com 2
1 Tx- Tx
2 Tx+ Rx
HONEYWELL SECURITY TECHNICAL BULLETIN 11 December 2008
www.asia.security.honeywell.com Rev 1.0 3 of 5
Device Configuration
Go to Control page to configure external CCTV peripherals which may be controlled by VideoBloX keyboard.
1. Copy the HNDR-S.db and HNDR-S.mb files to root directory “C:\Program
Files\Honeywell\VBloXCFG\DBF\”
2. Execute the VbloxCFG software and go to “Control” page.
3. Select the “Device Type” which is to be configured.
4. Click icon to browse “HNDR-S.db” which is locate in “C:\Program Files\Honeywell\VBloXCFG\DBF\”
5. Set “Com Port” to “1” if the control signal to the device is connected to the VideoBloX CPU master
communications port.
6. Set the “Control Type” to the type of interface used to control the external device.
7. Set “Switch Offset” to “-1” if no automatic video switch operation is required when the device is selected.
The offset will be added to the selected device number and the resulting value will be used as the matrix
video input channel which will be selected. e.g. Switch Offset =29, the first channel of HNDR-S DVR is
input 30.
8. Click “Download” button to download after changed.
HONEYWELL SECURITY TECHNICAL BULLETIN 11 December 2008
www.asia.security.honeywell.com Rev 1.0 4 of 5
HNDR-S 4848 DVR Configuration
1. Configure Communication port
a. Push Menu button of DVR and enter the DVR setting menu.
b. Move to System menu and select Serial Setup.
c. Move to COM2 485 and select Keyboard HTX-3000 as below figure.
2. Configure Keyboard Control Address and Keyboard PTZ address as below figure.
a. Push Menu button of DVR and enter the DVR setting menu.
b. Move to Miscellaneous menu.
c. Select Keyboard Control Address to 1.
HONEYWELL SECURITY TECHNICAL BULLETIN 11 December 2008
www.asia.security.honeywell.com Rev 1.0 5 of 5
HEGS5BLX Operation
To select “HNDR-S 4848”, press “DVR” button. Then press “1” + “Enter” buttons to select DVR number 1.
A B C D E F G H
KJIML
Joystick
DVR Function Keys
Item Function supported
by Keyboard Description
(The Keyboard should be in DVR mode for the below operation)
1 Menu Press “H”
2 Play Press “B”
3 Rewind Press “G”
4 Forward AUX Mode LED on, Press “C”
5 Search Press “C”
6 Sequence Press “F”
7 Select AUX Mode LED on, Press “E”
8 Multi-screen AUX Mode LED on, Press “F”
9 Exit AUX Mode LED on, Press “G”
10 Enter AUX Mode LED on, Press “H”
11 Up Hold down “ALT” + “Up”
12 Down Hold down “ALT” + “Down”
13 Left Hold down “ALT” + “Left”
14 Right Hold down “ALT” + Right”
I: Use to move between menu items
J: Select DVR channel depending on the position
K: Select DVR channel depending on the position
L: Select DVR channel depending on the position
15 DVR channel select
M: Use to move between menu items
* Detail DVR operation procedure, please refer to the DVR manual.
Note: The information contained herein is subject to change without notice.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de DVR de Honeywell
Honeywell
Honeywell HRDP16 Manual de usuario
Honeywell
Honeywell MAXPRO NVR Hybrid XE Manual del operador
Honeywell
Honeywell HRSD16 Manual de usuario
Honeywell
Honeywell HRHM1041 Manual de usuario
Honeywell
Honeywell HLVR4 Manual de usuario
Honeywell
Honeywell Rapid Eye Manual de usuario
Honeywell
Honeywell VISTA CADVR-1004C Manual de usuario
Honeywell
Honeywell Rapid Eye Manual
Honeywell
Honeywell HRG4X Manual de usuario
Honeywell
Honeywell HRDP DVR Manual de usuario
Honeywell
Honeywell HRHD4+ Manual de usuario
Honeywell
Honeywell HRXD Series Manual de usuario
Honeywell
Honeywell HD-16DVR-C Manual de usuario
Honeywell
Honeywell CADVR-04D Manual de usuario
Honeywell
Honeywell MAXPRO NVR XE Manual
Honeywell
Honeywell Rapid Eye Manual de servicio
Honeywell
Honeywell HSVR-04 Manual de usuario
Honeywell
Honeywell HD-DVR-1004 Manual de usuario
Honeywell
Honeywell Rapid Eye Manual de instrucciones
Honeywell
Honeywell HRDV 16 Duplex Instrucciones de funcionamiento originales
