Honeywell PRO 2000 Series Manual del propietario
To program the controller, perform the following procedures in the order listed:
Fig. 1 Program Menu
Press the MENU button, then select PROGRAM and press the button to view the
program menu.
!
Fig. 2
1. From the menu, use the and buttons to highlight RELAY 1.
2. Press the button to select RELAY 1 to view the parameters. Fig. 2 shows
RELAY 1.
"#
Fig. Program - Setpoint
1. From the menu, use the and buttons to highlight SETPOINT.
2. Press the button to display the setpoint value.
3. Use the and buttons to increase/decrease the desired setpoint
temperature.
Set the temperature to 45° F.
4. Press the button to accept the setpoint temperature and display the next
option.
Honeywell Series 2000
$"%%&#"'"#(
Fig. Program – Differential
1. From the menu, use the and buttons to highlight DIFFERNTL.
2. Press the button to display the differential value.
3. Use the and buttons to increase/decrease the desired value.
Set the value to 3° F.
4. Press the button to accept the value and display the next option.
)#&
Fig. Program – Sensor
1. From the menu, use the and buttons to highlight SENSOR.
2. Press the button to display the sensor selections.
3. Use the and buttons to select Sensor A or B.
Select sensor A.
4. Press the button to accept the highlighted sensor and display the next option.
*+,'
Fig. Program Heat/Cool
1. From the menu, use the and buttons to highlight HEAT/COOL (Default:
HEAT).
2. Press the button to display the heat and cool selections.
3. Use the and buttons to select Heat or Cool.
Select COOL.
4. Press the button to accept the highlighted selection and display the next
option.
____________________________________________________________________
-
Fig. Program – Exit
Press the EXITbutton to finish the programming for Relay 1.
Press the HOME button to leave programming mode and return to the home screen.
This completes the programming procedure for Cooling Only System.
To program the controller for time delay, perform the following procedures in the
order listed:
To access the Setup menu, press and hold the MENU button for five seconds. See
Fig. 1.
!
When you are working with the menus, use the:
•Left arrow button ( ) to scroll backward through the menus
•Right arrow button () to select the highlighted menu item and display
its content
•Up and Down arrow buttons (and ) to scroll up and down through a
list of items or to increase or decrease the value of a displayed parameter
NOTE: If you press the HOME
button or there is no keypad activity for four
Minutes, you exit Program mode and return to the home screen.
If you press the MENU button, you exit and return to the menu.
To go from Setup menu screen as shown in Fig. 1 to Min Off screen shown in Fig. 2,
follow the steps as listed below:
1. From the Setup menu (Fig. 1), use the Down arrow button () to highlight
OUTPUTS.
2. Press Right arrow button () to display the Outputs menu.
3. Press the Down arrow button () to highlight OPTIONS.
4. Press Right arrow button () to display the Options menu.
5. Press the Down arrow button () to highlight MIN OFF.
6. Press Right arrow button () to display the Min Off screen (Fig. 2).
" #$%&&'(
This is the minimum number of seconds of “off time” for all relays.
Use the Up and Down arrow buttons (and ) to increase/decrease the desired
number of seconds from 0 to 990 in 10 second increments.
Default: 0 (zero)
Range: 0 to 990 seconds
Aqua Air factory setting: 20 seconds
)*+
After entering the desired number of seconds, press HOME button to accept the seconds
and finish the programming process. The display should show Home screen.
_____________________________________________________________________
Otros manuales para PRO 2000 Series
14
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Controladores de Honeywell
Honeywell
Honeywell DBC2000 Series Manual de usuario
Honeywell
Honeywell HercuLine 2000 Series Manual de usuario
Honeywell
Honeywell Ex-Or Mid-Bay MS1200DIMBW Manual de instalación y operación
Honeywell
Honeywell VS820A Manual de usuario
Honeywell
Honeywell 1000 Series Manual de usuario
Honeywell
Honeywell SUPER TRADELINE S8610U Manual de usuario
Honeywell
Honeywell ML6161E Manual de usuario
Honeywell
Honeywell SLATE Manual de usuario
Honeywell
Honeywell R7515C MacroCel Manual de usuario
Honeywell
Honeywell KromSchroder IC 40 Manual
Honeywell
Honeywell Pressuretrol P7810C Manual de usuario
Honeywell
Honeywell UDC1200 MICRO-PRO Manual de usuario
Honeywell
Honeywell H808C Manual de usuario
Honeywell
Honeywell 4000 Series Manual de operación
Honeywell
Honeywell DCP301 Manual de usuario
Honeywell
Honeywell Excel 10 Manual de usuario
Honeywell
Honeywell V4055A Manual de usuario
Honeywell
Honeywell Z11S Manual de usuario
Honeywell
Honeywell L7224A Manual de usuario
Honeywell
Honeywell DCP552 Mark II Manual de usuario
