Honeywell HCE 60 Manual del propietario
Storey
Controller
HCE 60
Installation and Operation
Contents
1
Contents
Overview 3
Application 3
Installation procedure 4
Classifying zones and actuators 4
Installation 4
Configuration and electrical connection 4
Start-up 4
Creating a zoning plan 5
Determining temperature zones 5
Filling out zoning plan 6
Installation 10
Wall installation 11
DIN rail installation 12
Installing Hometronic components 12
Configuration and electrical connection 13
Opening housing 14
Cabling connections 16
Start-up 26
Preparing for start-up 26
LED indicators on storey controller 28
Operating modes of storey controller 29
Buttons 30
Cooling function 30
Contents
2
Assigning zones and issuing room names 32
Example: Assigning an HCW 22 setpoint adjuster to
zone 1 32
Example: Assigning room name LIVING to zone 1 34
Assigning wireless setpoint adjuster HCU 30 to a
temperature zone 36
Assigning setpoint adjusters of type HCW 23 to a zone 37
Assigning room names for cooling function 37
Canceling assignment 38
Deleting assignment of a room name at the Hometronic
Manager 39
Saving settings on Hometronic Manager 40
Checking configuration 40
Checking wireless transmission 41
Checking assignment of room names 42
Displaying faults 42
Completing start-up 43
Resetting storey controller to state of delivery 44
Appendix 45
Glossary 45
Help with problems 46
Overview of Hometronic heating components 49
Zoning plan 50
Notes 52
Overview
3
Overview
For your information
Technical terms are explained in the glossary (Page 45). They are
identified in the text by an *.
Application
The storey controller HCE 60 receives information on the temperature
of the room from the setpoint adjusters* and the Hometronic Man-
ager. Using this information, the storey controller regulates the boiler
feedback*, the pump relay*, and the thermal actuators* (see Page 48,
Hometronic heating components).
It has a self-learning controller (fuzzy logic) which automatically ad-
justs itself to the ambient conditions. The desired room temperature is
reached quickly and then maintained.
A sticker has been included on the back for a quick overview of the
display and operation. It can be attached to the housing of the storey
controller.
Overview
4
Installation procedure
Classifying zones and actuators
•Determine which heating circuits* are controlled by the storey
controller.
Installation
•Install Hometronic components.
Configuration and electrical connection
•Set the storey controller to the actuator type, attach cables to the
respective connections and connect components together.
Start-up
•Assign setpoint adjusters and any room temperature sensors to the
temperature zones.
•Assign room names at the Hometronic Manager if necessary.
•Assign the time program of the wireless setpoint adjuster HCU 30
to the temperature zones if necessary.
Creating a zoning plan
5
Creating a zoning plan
A temperature zone is an area of the building, e.g. a room, in which
the setpoint temperature* is set with a setpoint adjuster. The storey
controller controls all thermal actuators of a temperature zone identi-
cally.
5 temperature zones can be set up for each storey controller. The
expansion module HCS 60 increases the number of temperature
zones for each storey controller to 8. A maximum of 3 actuators can
be connected in each zone.
Thus the total number of actuators which can be controlled by one
storey controller is limited to 24.
Determining temperature zones
Caution
Damage caused by equipment from other manufac-
turers!
The storey controller was designed for use with com-
ponents from Honeywell only!
►Use only H 200 BG (closed without current) or H 200 BO (open
without current)-type actuators.
►Group actuators (by type and location) which are managed by the
storey controller.
►Group together all actuators which are controlled by a setpoint ad-
juster in a temperature zone.
Creating a zoning plan
6
For more than 8 temperature zones or 24 actuators:
►Determine the number of additional storey controllers required using
the following table:
Temperature
zones (maximum)
Actuators
(maximum)
No. of
storey controllers
824 1
16 48 2
24 72 3
The example at the end of this section shows zone divisions
with corresponding zoning plan.
Filling out zoning plan
►Copy the sample zoning plan (see Appendix, Page 50) (archive it).
►Enter the type and installation location of the respective actuator in
each temperature zone.
►Assign a setpoint adjuster to each temperature zone.
►Assign room names if necessary.
►Hand over the zoning plan to the customer after installation.
Creating a zoning plan
7
Example of zone divisions
1, 2 etc. = Zone
A = Living room E = Bedroom
B = Dining room F = WC
C = Kitchen G= Bathroom
D= Hall
Creating a zoning plan
8
This example shows:
•The living area is covered by 6 temperature zones. The additional
module HCS 60 is required for this partitioning.
•A total of 8 actuators are controlled by the storey controller.
Up to 8 temperature zones can be controlled by the additional module
HCS 60. Planned temperature zones are generated in gray.
The room names for each temperature zone are entered at
the Hometronic Manager.
Tabla de contenidos
Otros manuales de Controladores de Honeywell
Honeywell
Honeywell DBC2000 Series Manual de usuario
Honeywell
Honeywell VS820A Manual de usuario
Honeywell
Honeywell J48 Manual de usuario
Honeywell
Honeywell UDC1200 MICRO-PRO Guía del usuario
Honeywell
Honeywell ML6420 Manual de operación
Honeywell
Honeywell HON 5020 Manual de usuario
Honeywell
Honeywell HON 372 Manual
Honeywell
Honeywell UDC3200 series Manual de usuario
Honeywell
Honeywell WEBsAX Series Guía
Honeywell
Honeywell HC900 Manual de usuario
Honeywell
Honeywell UDC 6300 Guía
Honeywell
Honeywell MS7510A2008 Manual de usuario
Honeywell
Honeywell SUPER TRADELINE S8610U Manual de usuario
Honeywell
Honeywell HVC0001 Manual de usuario
Honeywell
Honeywell Pro-Watch 7000 Manual de usuario
Honeywell
Honeywell ML4195E Manual de usuario
Honeywell
Honeywell N05010 Manual de operación
Honeywell
Honeywell EXCEL 10 W7753A Manual de usuario
Honeywell
Honeywell Experion 8 Series Manual
Honeywell
Honeywell CIPer 50 Manual de usuario
