Honeywell Excel 15 W7760A Manual de usuario

Excel 15 W7760A

EPROM REPLACEMENT

DESCRIPTION 5. Remove galvanized plate. Place on adjacent work

This EPROM Replacement procedure outlines the surface in the orientation as it was removed

process to upgrade the Excel 15 W7760A Controller to

the latest firmware release.

Firmware replacement kit: Part # 32004159-002 Plate

Procedure will apply to future firmware as released. Work Surface

Material Needed

1. Replacement EPROM. Programmed with new Firmware Side View

2. #10 Tork Driver (preferred), or 3/16" thin flat-blade

screwdriver 6. Set aside paper protective sheet, then remove 2 screws

that secure board to cover.

3. Extraction Tool: AMP PLCC Extraction Tool 821903-50

00, AMP 822154-1 00, or small diameter probe/object

(i.e. paper clip)

Procedure

1. Discharge static electricity form body by touching known

earth ground. 7. Making certain you are grounded. Remove the circuit

2. Remove W7760A from wiring subbase. Place controller board and place it component side up, pin side down on

on work surface with pins and label side up. top of the galvanized plate. Extend pins over the edge

on each side of the galvanized plate.

3. Remove plastic, anti-static sheet. (This sheet contains

device information) – Set aside.

Caution: Do not tear plastic protective sheet at

corners.

oard

Plate

4. Using the #10 Tork Driver or flat-bladed screwdriver

remove the four screws around perimeter. Put the

screws aside in a secure place for later re-assembly. Work Surface

Side View

®U.S. Registered Trademark

95- 7631

Excel 15 W7760A EPROM Replacement

REPLACEMENT

PROM

Note: Orient the board with heat sink to

left. The EPROM to be replaced is the

socketed component located closest to

the component labeled Echelon Heat Sink

Home and Building Control Home and Building Control Home and Building Control Products

Honeywell Inc. Honeywell Limited-Honeywell Limitee Honeywell AG

Honeywell Plaza 155 Gordon Baker Road Böblinger Straße 17

P.O. Box 524 North York Ontario D-71101 Schönaich

Minneapolis, MN 55408-0524 M2H 3N7 Phone (49-7031) 637-01

Fax (49-7031) 637-493

Echelon

Jack

8. Insert the tips of the Extraction Tool in the diagonal slots of the micro socket, and slowly remove the EPROM with a

rocking motion.

9. Again, making certain you are grounded, insert the new EPROM into the socket, orienting the notch in the chip with the

notch in the socket in the lower right hand corner. The EPROM may be inserted into the socket by placing it on top of the

socket and pressing it into place with thumb pressure until it is seated. While pressing the EPROM into the socket, keep

another finger on the rear of the circuit board behind the socket so the board is not stressed while pressing with the thumb.

10. Turn the circuit board upside down again and orient it on the cover. Replace the two center screws.

11. Replace the protective paper and the galvanized plate. Replace the 4 screws in each corner.

12. Replace the labeled plastic sheet.

13. Keep EPROM in a safe place until system operation has been confirmed.

14. Make a record of the W7760A as being updated. It is good idea to make a mark on the controller to that effect as well.

15. Reinstall the W7760A.

Printed in U.S.A. on recycled

paper containing at least 10%

95-7631 D.B. 12-99

post-consumer paper fibers.

www.honeywell.com

Otros manuales de Controladores de Honeywell

Honeywell

Honeywell ML6984 Manual de usuario

Honeywell

Honeywell Touchpoint Plus Nota de versión

Honeywell

Honeywell Design and Application Manual del producto

Honeywell

Honeywell DCP 250 Guía de instalación

Honeywell

Honeywell UDC2500 Manual de usuario

Honeywell

Honeywell Z11S Manual de usuario

Honeywell

Honeywell S05 Series Manual de usuario

Honeywell

Honeywell UDC3500 Manual de usuario

Honeywell

Honeywell Pressuretrol P7810A Manual de operación

Honeywell

Honeywell PW6K1ICE Manual del operador

Honeywell

Honeywell M7061 Manual de usuario

Honeywell

Honeywell N20010 Manual de usuario

Honeywell

Honeywell CIPer 50 Manual de instalación y operación

Honeywell

Honeywell Excel 10 Manual de usuario

Honeywell

Honeywell T775U2006 Manual de usuario

Honeywell

Honeywell MIWI350 Manual de usuario

Honeywell

Honeywell UDC1200 MICRO-PRO Guía del usuario

Honeywell

Honeywell HercuLine 10260A Manual de usuario

Honeywell

Honeywell MN6110 Manual de usuario

Honeywell

Honeywell CENTRA LINE EAGLEHAWK NX Manual de instalación y operación

Honeywell

Honeywell Scan Dome ll HTX-2500 Manual del propietario

Honeywell

Honeywell Excel 100C Manual de usuario

Honeywell

Honeywell Experion C300 Manual de usuario

Honeywell

Honeywell T775B Guía de instalación

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario