Honeywell GSMVLP5 Instrucciones de montaje

800-08115 1/11 Rev. B

GSMVLP5 GSM and

ILP5 Ethernet

Communications Modules

Installation and Setup Guide

Installing Communication Modules

RF Exposure

WARNING: The antenna(s) used for this transmitter must be installed to provide a separation distance of

at least 20 cm from all persons and must not be co-located or operating in conjunction with any other

antenna(s) or transmitter.

Installing the GSMVLP5 in the LYNX Touch Series Control

Ensure that SIM card and the connector board are securely installed in the GSMVLP5 before installing the

module in the LYNX Touch.

1. Install the provided FCC/IC label (P/N 800-08334) on the control’s case back (refer to Figure 1).

5000-100-186-V0

FCC ID: CFS-8DLLYNXTOUCH1

IC: 573F-LYNXTOUCH1

THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES AND RSS 210 OF INDUSTRY

CANADA. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS

DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST

ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY

CAUSE UNDESIRED OPERATION.

800-08126 1/11 Rev A

LYNX TOUCH SERIES

COMPLIES WITH FCC RULES, PART 68 FCC REGISTRATION NO.: AC3AL05BL5000

RINGER EQUIVALENCE: 0.1B

IC MODEL: LYNXTOUCH1

CONTAINS TRANSMITTER MODULE

IC: 7830A-MC55I

FCC ID: QIPMC55I

800-08334 2/11 Rev A

FCC ID: CFS-8DLLYNXTOUCH1

IC: 573F-LYNXTOUCH1

LYNX TOUCH SERIES

IC MODEL: LYNXTOUCHG1

Figure 1. FCC/IC Label Location

2. Release the LYNX Touch front case from the back case by depressing the two locking tabs at the top of the

unit with the blade of a medium size screwdriver (Refer to Figure 2).

3. Install the GSMVLP5 into the LYNX Touch control front case. Ensure that the connector board is properly

seated into the receptacle on the control (Refer to Figure 2).

4. Secure the GSMVLP5 with the three provided screws (Refer to Figure 2).

5. Enable the GSMVLP5 device, configure alarm reporting and module supervision and register the device.

Refer to the “Program the Radio” and “Diagnostics” sections in the LYNX Touch Series Installation and

Setup Guide (P/N 800-06834 or higher).

For Documentation and Online Support: http://www.security.honeywell.com/hsc/resources/MyWebTech

SCREW

(3)

SIM

CARD

5000-100-151-V1

ROTATED

180

CONNECTOR

BOARD

CONNECTOR

BOARD

RECEPTACLE

GSMVLP5

LYNX TOUCH

LOCKING TABS

Figure 2. Installing the GSMVLP5 in the LYNX Touch

Installing the ILP5 in the LYNX Touch Series Control

Ensure that the connector board and cable are securely installed in the ILP5 before installing the module

the LYNX Touch.

1. Release the LYNX Touch front case from the back case by depressing the two locking tabs at the top of the

unit with the blade of a medium size screwdriver (Refer to Figure 3).

2. Using a wire cutter or knife cut the plastic tabs that secure the ILP5 spacer to the back case of the LYNX

Touch (Refer to Figure 3).

3. Remove the ILP5 receptacle knockout from the left side of the LYNX Touch back case (Refer to Figure 3).

4. Install the ILP5 into the LYNX Touch control front case. Ensure that the connector board is properly seated

into the receptacle on the control (Refer to Figure 3).

5. Secure the ILP5 with the three provided screws (Refer to Figure 3).

6. Insert the ILP5 receptacle and spacer into the slot on the back case (Refer to Figure 3).

7. Secure the communications cable to the tie wrap point on the ILP5 with the provided tie wrap (Refer to

Figure 3).

8. Enable the ILP5 and configure alarm reporting and module supervision and register the device. Refer to the

“Program the Radio” and “Diagnostics” sections in the LYNX Touch Series Installation and Setup Guide

(P/N 800-06834 or higher).

For Documentation and Online Support: http://www.security.honeywell.com/hsc/resources/MyWebTech

5000-100-154-V1

SCREW

(3)

ROTATED

180

CONNECTOR

BOARD

RJ45

RECEPTACLE

CONNECTOR BOARD

RECEPTACLE

ILP5

LYNX TOUCH

TIE

WRAP

POINT

REMOVE ILP5

SPACER

ILP5 SPACER

REMOVE ILP5

KNOCKOUT

TIE

WRAP

(1)

RJ45 RECEPTACLE

LYNX TOUCH

ALTERNATE INSTALLATION

LOCKING TABS

ETHERNET CABLE

TO ILP5

Figure 3. Installing the ILP5 in the LYNX Touch

Electrical Specifications

GSMVLP5

Voltage Input 5V

Current

Idle 15 mA, standby

Average 300mA, average transmit

Peak 1.6A peak transmit, 25% duty cycle

ILP5

Voltage Input 5V

Current: 83 mA, 100 Base T with traffic

41 mA, 10 Base T with traffic

2 Corporate Center Drive, Suite 100

P.O. Box 9040, Melville, NY 11747

www.honeywell.com/security

Ê800-08115!Š

800-08115 1/11 Rev. B

Tabla de contenidos

Otros manuales de Unidad de control de Honeywell

Honeywell

Honeywell AlarmNet IGSMHS Instrucciones de montaje

Honeywell

Honeywell Kromschroder GIK Series Manual de usuario

Honeywell

Honeywell VQ400 Series Manual de usuario

Honeywell

Honeywell W6215 Series Manual de operación

Honeywell

Honeywell D05T Manual de usuario

Honeywell

Honeywell V4730B Manual de usuario

Honeywell

Honeywell VR4300 Manual de usuario

Honeywell

Honeywell Braukmann D05 Manual de usuario

Honeywell

Honeywell S4560B1006 Manual de usuario

Honeywell

Honeywell VC7900 Series Manual de operación

Honeywell

Honeywell IntelliDoX Manual de usuario

Honeywell

Honeywell RM7800L1087 Manual de usuario

Honeywell

Honeywell VE4000 Series Manual de usuario

Honeywell

Honeywell VC Series Manual de usuario

Honeywell

Honeywell krom schroder BCU 440 Manual de usuario

Honeywell

Honeywell VISTA Manual de usuario

Honeywell

Honeywell V800 Manual de usuario

Honeywell

Honeywell NK295C Manual de usuario

Honeywell

Honeywell NOTIFIER NZM-100 Manual de usuario

Honeywell

Honeywell L506 Manual de usuario

Honeywell

Honeywell 3GL Manual de usuario

Honeywell

Honeywell Notifier NFG-8 Manual de usuario

Honeywell

Honeywell SG160S Manual de usuario

Honeywell

Honeywell FY 30 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario