Hobie 14 Manual de usuario

#13070100 / Page 1 of 1

#13070100 - COMPTIPTM RETROFIT INSTRUCTIONS

HOBIE 14, 16, 18 AND HR14

1) REMOVE MAST TANG OR TANGS (HR14) BY DRILLING OFF RIVET

HEADS W/ A 13/64” (4 MM) DRILL BIT AND PUNCHING RIVET CASINGS

AND CAPS THROUGH.

2) MEASURE FROM THE BOTTOM OF THE

MAST EXTRUSION (NOT INCLUDING MAST

BASE). NOTE: CUT SHOULD BE ABOVE

TANG RIVET HOLES!

MARK AND CUT OFF MAST SQUARE AT THE

APPROPRIATE LENGTH. (HINT: WRAP A

SHEET OF PAPER AROUND THE MAST AND LINE UP EDGES TO MAKE

A PERFECTLY SQUARE MARK ALL AROUND THE MAST. TAPE IN

PLACE AT THE CUT POINT. PENCIL A THICK LINE ALL AROUND THE

MAST FOLLOWING THE PAPERS EDGE. WITH A HACK SAW, START

CUTTING ON THE LINE AND ROLL THE MAST OVER AS YOU CUT. CUT

A “TRENCH” ALLAROUND THE MAST BEFORE CUTTING THROUGH

WHILE ROLLING THE MAST SLOWLY OVER. (STARTING A CUT AND

CONTINUING STRAIGHT THROUGH MAY NOT CUT STRAIGHT.)

3) DRILL A 3/8" DIA. HOLE, 9" DOWN FROM CUT (ON THE FRONT) AS SHOWN (FIG. 1).

4) INSERT ETHAFOAM PLUG TO A DEPTH OF 12" (FIG. 2). THIS PLUG MAY BE GLUED IN PLACE

WITH PLENTY OF 3M 5200 OR SIKAFLEX IF DESIRED. OTHERWISE USE FOAM INJECTION AS

DESCRIBED BELOW. IF GLUED IN PLACE, THE PLUG MUST CURE FOR 24 HOURS BEFORE

CONTINUING INSTALLATION.

5) FILE COMPTIPTM FOR A SNUG FIT INSIDE EXTRUSION. CHECK THAT TIP WILL FULLY INSERT.

6) PLACE LOWER MAST ON SAW HORSES OR LARGE TABLE WITH MAST BASE AGAINST SOLID

PADDED OBJECT (THAT YOU CAN BE BANG MAST BASE AGAINST). GLUED ASSEMBLY WILL HAVE

TO BE HELD LEVELAND SQUARE WHILE CURING, PREPARE ADDITIONAL SAW HORSE IF

NECESSARY.

7) MASK OFF EXTRUSION AND LUFF TRACK OPENINGS AS WELL AS COMPTIPTM. SPREAD EPOXY

OR POLYESTER PUTTY INSIDE OF EXTRUSION AT CUT END TO A DEPTH OF 6". SPREAD

MATERIAL OUTSIDE ON COMPTIPTM JOINT.

8) INSERT COMPTIPTM. HOLD TIP WHILE INSERTING. PUSH INTO EXTRUSION WITH MAST BASE AGAINST SOLID OBJECT. AS TIP

GETS TIGHTER, PULL ENTIRE ASSEMBLY BACK AWAY FROM THE SOLID OBJECT, THEN SHOVE BACK AGAINST IT (IN A BATTERING

RAM MOTION). REPEAT UNTIL TIP IS FULLY INSERTED. BRACE ASSEMBLY IN A POSITION TO HOLD MAST AND TIP SQUARE ON ALL

AXIS AS EPOXY CURES.

9) H-16 NOTE: IF TANG IS AN OLD STYLE OR IS DAMAGED REPLACE IT. CURRENT TANG HAS 3 HOLES FOR STAYS AND TRAPEZE

WIRE ATTACHMENT. USING EXISTING HOLES IN EXTRUSION, DRILL COMPTIPTM FOR TANG RIVET AND SLEEVES WITH A 13/64” (4

MM) DRILL BIT AND REINSTALL MAST TANG WITH RIVETS AND RIVET CAPS.

INTERNAL SEALING PLUG:

10) TAPE OFF AREA AROUND 3/8" HOLE TO REDUCE CLEANUP AFTER FOAM INSTALLATION.

11) TILT MAST FOR FOAMING, HEAD DOWN, AS SHOWN. (FIG. 3)

12) (READ FOAM INSTRUCTIONS PRIOR TO USE) INJECT A/B

URETHANE FOAM INTO 3/8" HOLE" (APPROX. 3 SECOND SQUIRT)

PLUG HOLE WHILE FOAM EXPANDS. FOR BEST RESULTS, FOAM AND

MAST SHOULD BE ABOVE: 70° F.

13) AFTER FOAM HAS CURED FOR AN HOUR OR MORE, CLEANUP UP

EXCESS WITH A SINGLE EDGE RAZOR BLADE AND INSTALL 3/8"

PLUG INTO 3/8" HOLE.

CUT LENGTHS ARE:

H14 I5' 1 1/8"

H16 18’ 3 3/4"

H18 20’ 5 3/8"

HR14 14' 4 3/8"

Otros manuales para 14

1

Este manual sirve para los siguientes modelos

4

Otros manuales de Bote de Hobie

Hobie

Hobie HOBIE Miracle 20 Manual de usuario

Hobie

Hobie 16 Manual de usuario

Hobie

Hobie Mirage Outback Manual de usuario

Hobie

Hobie T1 Manual de usuario

Hobie

Hobie 18 Manual de usuario

Hobie

Hobie Mirage Vantage CT Manual de usuario

Hobie

Hobie 18 SX Manual de usuario

Hobie

Hobie 18 Manual de usuario

Hobie

Hobie Fx One Guía de configuración

Hobie

Hobie Mirage Kayak Manual de usuario

Hobie

Hobie Mirage Drive Manual

Hobie

Hobie 17 Manual de usuario

Hobie

Hobie Quest 13 Manual de usuario

Hobie

Hobie H14 Manual de usuario

Hobie

Hobie HOBIE MAUI Manual de usuario

Hobie

Hobie Mirage i12s Manual de usuario

Hobie

Hobie teddy Manual de usuario

Hobie

Hobie Getaway Manual de usuario

Hobie

Hobie SPORT CRUISER 21 Manual de usuario

Hobie

Hobie 15 Manual de usuario

Hobie

Hobie Mirage Tandem Island Manual de usuario

Hobie

Hobie Bravo Manual de usuario

Hobie

Hobie Mirage Pro Angler 17T Manual de usuario

Hobie

Hobie 18 Manual de usuario

Manuales populares de Bote de otras marcas

Raymarine

Raymarine ST70 Instrument Manual de usuario

Pro-Line Boats

Pro-Line Boats Pro Line 19 Sport Manual de usuario

Jeanneau

Jeanneau CAP CAMARAT 8.5 CC Manual de usuario

Tiara Yachts

Tiara Yachts C49 2024 Manual de usuario

Monterey Boats

Monterey Boats Sport Yacht 330 Manual de usuario

J

J 105 Manual de usuario

PURSUIT

PURSUIT OS 335 Manual de usuario

Boston Whaler

Boston Whaler CONQUEST 345 Manual de usuario

Jeanneau

Jeanneau SUN ODYSSEY 41 DS Manual de usuario

Meridian

Meridian 490 Pilothouse Manual de usuario

Advanced Elements

Advanced Elements AdvancedFrame Expedition AE1009 Manual de usuario

Robo Marine Indonesia

Robo Marine Indonesia GEOMAR Manual de usuario

Swallow Boats

Swallow Boats BayRaider Manual de usuario

Intex

Intex Excursion 5 Set Manual de usuario

X SHORE

X SHORE EELEX 8000 Manual de usuario

ISLAND PACKET

ISLAND PACKET 370 Manual de usuario

Sea Ray

Sea Ray 175 Sport Manual de usuario

Regal

Regal 2300 Manual de usuario