HK Instruments DPT-Ctrl-MOD Series Manual de usuario

INSTALLATION

INSTRUCTIONS

Pressure and flow controllers

DPT-Ctrl-MOD Series

• READ THESE INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO

INSTALL, OPERATE OR SERVICE THIS DEVICE.

• Failuretoobservesafetyinformaonandcomplywithinstruconscan

result in PERSONAL INJURY, DEATH AND/OR PROPERTY DAMAGE.

• Toavoidelectricalshockordamagetoequipment,disconnectpower

beforeinstallingorservicinganduseonlywiringwithinsulaonratedfor

fulldeviceoperangvoltage.

• Toavoidpotenalreand/orexplosiondonotuseinpotenally

ammableorexplosiveatmospheres.

• Retaintheseinstruconsforfuturereference.

• Thisproduct,wheninstalled,willbepartofanengineeredsystemwhose

specicaonsandperformancecharacteriscsarenotdesignedor

controlledbyHKInstruments.Reviewapplicaonsandnaonalandlocal

codestoassurethattheinstallaonwillbefunconalandsafe.Useonly

experiencedandknowledgeabletechnicianstoinstallthisdevice.

Thankyoufor choosing an HK InstrumentsDPT-Ctrl-MOD series air han-

dling controller with dierenal pressure or airow transmier. The DPT-

Ctrl-MODseriesPIDcontrollersareengineeredforbuildingautomaonin

theHVAC/Rindustry.Withthe built-incontroller oftheDPT-Ctrl-MOD it

ispossibletocontroltheconstantpressureorowoffans,VAVsystemsor

dampers.Whencontrollingairow,itispossibletoselectafanmanufacturer

oracommonmeasuringprobethathasaK-value.

TheDPT-Ctrl-MODincludes anInputterminalthat enables the reading of

mulple signals such as temperature or control relays over Modbus. The

Input terminal has one input channel designed to accept 0−10 V, ntc10k,

Pt1000,Ni1000/(-LG),andBININ(potenalfreecontact)signals.

DPT-Ctrl-MODseriesdevicesarecommonlyusedinHVAC/R

systems for:

•Controllingdierenalpressureorairowinairhandlingsystems

•VAVapplicaons

•Controllingparkinggarageexhaustfans

SPECIFICATIONS

Performance

Accuracy (from applied pressure):

Pressure<125Pa=1%+±2Pa

Pressure>125Pa=1%+±1Pa

(Accuracyspecicaonsinclude:generalaccuracy,

linearity,hysteresis,longterm

stability,andrepeonerror)

Thermal eects:

Temperaturecompensated0...50°C

Overpressure:

Proofpressure:25kPa

Burstpressure:30kPa

Zero point calibraon:

ManualpushbuonorModbus

Response me:

1.0−20s,selectableviamenuorModbus

Communicaon

Protocol:MODBUSoverSerialLine

TransmissionMode:RTU

Interface:RS485

Byteformat(11bits)inRTUmode:

 Codingsystem:8-bitbinary

 Bitsperbyte:

  1startbit

  8databits,leastsignicantbitsent

  rst

  1bitforparity

  1stopbit

Baudrate:selectableinconguraon

Modbusaddress:1–247addressesselectablein

conguraonmenu

Technical Specicaons

Media compability:

Dryairornon-aggressivegases

Controller parameter (selectable via menu and

Modbus):

Setpoint0...2500

P-band0...10000

I-me0...1000

D-factor0...1000

Pressure units (selectable via menu):

Pa,kPa,mbar,inWC,mmWC,psi

Flow units (selectable via menu):

Volume: m3/s, m3/hr,cfm,l/s

Velocity:m/s,/min

Measuring element:

MEMS,noow-through

Environment:

Operangtemperature:-20...50°C

Storagetemperature:-40...70°C

Humidity:0to95%rH,noncondensing

Physical

Dimensions:

Case:102.0x71.5x36.0mm

Weight:

150g,withaccessories290g

Mounng:

2each4.3mmscrewholes,onesloed

Materials:

Case: ABS

Lid:PC

Pressure inlets: Brass

Ductconnectors:ABS

Tubing:PVC

Protecon standard:

IP54

Display

2-linedisplay(12characters/line)

 Line1:Direconofcontroloutput

 Line2:Pressureorairowmeasurement, 

 selectableviamenu

  Ifinputisselected,line2showsalso

  inputinformaon(forexample 

 temperature)

Size:46.0x14.5mm

Electrical connecons:

4+4posionspring-loadedterminals

Wire:0.2–1.5mm2(12–24AWG)

Cable entry:

Strainrelief:M16

Knockout:16mm

Pressure ngs

5.2mmbarbedbrass

+Highpressure

−Lowpressure

Electrical

Voltage:

Circuit:3-wire(VOut,24V,GND)

Input:24VACorVDC,±10%

Output:0–10V

Powerconsumpon:<1.0W

Resistanceminimum:1kΩ

Conformance

MeetsrequirementsforCEmarking:

EMCDirecve2014/30/EU

RoHSDirecve2011/65/EU

WEEEDirecve2012/19/EU

INTRODUCTION WARNING

APPLICATIONS

COMPANY WITH

MANAGEMENT SYSTEM

CERTIFIED BY DNV GL

= ISO 9001 = ISO 14001 =

RoHS 2

2011/65/EU

SCHEMATICS

INSTALLATION

STEP 1: MOUNTING THE DEVICE

1)Mountthedeviceinthedesiredlocaon(seestep1).

2)Openthelidandroutethecablethroughthestrainreliefandconnectthe

wirestotheterminalblock(s)(seestep2).

3)Thedeviceisnowreadyforconguraon.

WARNING!Applypoweronlyaerthedeviceisproperlywired.

1)Selectthemounnglocaon(duct,wall,panel).

2)Usethedeviceasatemplateandmarkthescrewholes.

3)Mountwithappropriatescrews.

Display connecon

24 V

GND

LEDs

Joysck 1

Joysck 2

Joysck 3

Select

Down

Menu buons

Terminal

blocks

Pressure

sensor

Input terminal

conﬁguraon

jumpers

Control out

Input

GND

Figure 1a - Mounng orientaon

YES NO NO

STEP 3: CONFIGURATION

1)Zeropointadjustment.Formoreinformaon,seeStep4.

PRESS. UNIT

SELECT

DOWN

When control unit FLOW is selected.

2.2.0)Selectthefunconingmodeofthecontroller

-SelectManufacturerwhenconnecngDPT-Ctrl-MODtoafanwithpressure

measurementtaps

-SelectCommon probewhenusingDPT-Ctrl-MODwithacommon

measurementprobethatfollowstheformula:

 q=k∙√∆P(i.e.FloXact)

SELECT

ZERO SENSOR

SELECT

DOWN

2)Selectthefunconingmodeofthecontroller:PRESSUREorFLOW.

-SelectPRESSUREwhencontrollingdierenalpressure.

Gotopoint2.1.

-SelectFLOWwhencontrollingairow.

Gotopoint2.2.0.

CONTROL UNIT

PRESSURE

SELECT

DOWN

When control unit PRESSURE is selected.

2.1)Selectpressureunitfordisplayandoutput:Pa,kPa,mbar,inWCor

mmWC.Thengotopoint3.

MANUFACTURER

Common probe

SELECT

DOWN

Common probe Flakt Woods

SELECT

DOWN

STEP 2: WIRING DIAGRAMS

ForCEcompliance,aproperlygroundedshieldingcableisrequired.

1)Unscrewthestrainreliefandroutethecable(s).

2)Connectthewiresasshowningure2aand2b.

3)Tightenthestrainrelief.

Figure 2a - Wiring diagram

24 V

GND

+Power Supply

24VDC / 24VAC

Control out

Input

GND

Modbus

Figure 2b - Wiring diagram example for input signals

Input

GND

ntc10k J1

Input ntc10k temperature:

Funcon 04 - Read input register 3x0007

2.2.1)If

Commonprobe

selected:selectmeasurementunitsusedinthe

formula(akaFormulaunit)(i.e.l/s)

b. If

Commonprobe

selectedinstep1:

Each common probe hasa specicK-value. Selectthe K-valuefromcommon

probemanufacturer’sspecicaons.

AvailableK-valuerange:0.001...9999.000

FORMULA UNIT

l/s

SELECT

DOWN

2.2.2)SelectK-value

a.Ifmanufacturerselectedinstep1:

Each fan has aspecic K-value.Select the K-value from fanmanufacturer’s

specicaons.

K-VALUE

9000.000

SELECT

DOWN

2.2.3)Selectowunitfordisplayandoutput:

Flowvolume:m3/s, m3/h,cfm,l/s

Velocity:m/s,f/min

FLOW UNIT

m3/s

SELECT

DOWN

6)Selecttheresponseme:1...20s.

RESPONSETIME

20 s

SELECT

DOWN

3)SelecttheaddressforModbus:1...247

BAUD RATE

9600

SELECT

DOWN

ADDRESS

SELECT

DOWN

PARITY BIT

NONE

SELECT

DOWN

4)Selectthebaudrate:9600/19200/38400.

5)Selecttheparitybit:None/Even/Odd

7)Selecttheinputtype.

Passivetemperaturesensors:PT1000,NTC10k,Ni1000LG,Ni1000

Voltageinput0–10V:Vinput

Noinput:None

INPUT

PT1000

SELECT

DOWN

8)Selectthesetpointofthecontroller.

REF FLOW

0.025 m3/s

SELECT

DOWN

REF PRESSURE

100 Pa

CONFIGURATION CONTINUED

NOTE! Always zero the device before use.

Supplyvoltagemustbeconnectedonehourbeforethezeropointadjust-

mentiscarriedout.AccessviaModbusorbypushbuon.

1)Loosebothtubesfromthepressureinlets+and-.

2)Acvatethedevicemenubypushingthetheselectbuonfor2

seconds.

3)SelectZero sensorbypressingtheselectbuon.

4)WaitunltheLEDturnsoandtheninstalltubesagainforthe

pressureinlets.

STEP 4: ZERO POINT ADJUSTMENT

SELECT

STEP 5: INPUT SIGNAL CONFIGURATION

InputsignalscanbereadoverModbusviaDPT-MODRS485interface.

Signals Accuracy for measurement Resoluon

0...10V <0,5% 0,1%

NTC10k <0,5% 0,1%

Pt1000 <0,5% 0,1%

Ni1000/(-LG) <0,5% 0,1%

BININ(potenalfreecontact)

Thejumpersshouldbe set accordingtothe instruconsbelowandthe value

shouldbereadfromtherightregister.

Figure 3 - Input signal conguraon

NTC10k / BIN IN

Pt1000 / Ni10007(-LG)

0...10 V

D-VALUE

1.00

SELECT

DOWN

12)Pushtheselectbuontoexitmenu.

SELECT

EXIT MENU SELECT

9)Selectproporonalbandaccordingtoyourapplicaon

specicaons.

P-VALUE

206

SELECT

DOWN

10)Selectintegraonmeaccordingtoyourapplicaon

specicaons.

I-VALUE

4.00

SELECT

DOWN

11)Selectderivaonmeaccordingtoyourapplicaon

specicaons.

STEP 6: TEMPERATURE COMPENSATION

Thedeviceincludesanoutdoortemperaturecompensaonfunconthatcan

beenabledfromthemenu.Whenacvatedandanoutdoortemperaturesensor

isaached,theeecvesetpointofthedevicewillbemodiedtocompensate

forthecoldoutdoorair.Thismayresultinenergysavings.

If temperaturecompensaonis enabled, thedevicewill linearly decrease the

user’s setpoint (REF FLOW/REF PRESSURE) by 0 % to TC DROP % from TC

START TE to TC STOP TE.

Thedeviceenforcesa+5 °Cdierence betweenthe startand stoptempera-

tures.Thestarttemperaturemustbehigherthanthestoptemperature.

1)Connectandcongureanoutdoorairtemperaturesensor.Seestep5.

2)Enabletemperaturecompensaon.

4)Setthestoppingtemperatureforcompensaon.

TC STOP TE

-15 °C

SELECT

DOWN

TEMP COMP

SELECT

DOWN

TC START TE

5 °C

SELECT

DOWN

3)Setthestarngtemperatureforcompensaon.

5)Setthemaximumdroppercentageforcompensaon.

TC DROP %

25.0

SELECT

DOWN

Thesellerisobligatedtoprovideawarrantyofveyearsforthedeliveredgoods

regarding material and manufacturing. The warranty period is considered to

startonthedeliverydateoftheproduct.Ifadefectinrawmaterialsorapro-

ducon aw isfound, theseller isobligated,when theproduct issent tothe

sellerwithoutdelayorbeforeexpiraonofthewarranty,toamendthemistake

athis/herdiscreoneitherbyrepairingthedefecveproductorbydelivering

freeofchargetothebuyeranewawlessproductandsendingittothebuyer.

Deliverycostsfortherepairunderwarrantywillbepaidbythebuyerandthe

returncostsbytheseller.Thewarrantydoesnotcomprisedamagescausedby

accident,lightning,oodorothernaturalphenomenon,normalwearandtear,

improperorcarelesshandling,abnormaluse,overloading,improperstorage,in-

correctcareorreconstrucon,orchangesandinstallaonworknotdonebythe

seller.Theseleconofmaterialsfordevicespronetocorrosionisthebuyer’s

responsibility,unlessotherwiseislegallyagreedupon.Shouldthemanufacturer

alterthestructureofthedevice,thesellerisnotobligatedtomakecomparable

changestodevicesalreadypurchased.Appealingforwarrantyrequiresthatthe

buyerhascorrectlyfullledhis/herduesarisenfromthedeliveryandstated

inthe contract.Thesellerwillgivea new warranty for goodsthat havebeen

replacedorrepairedwithinthewarranty,howeveronlytotheexpiraonofthe

originalproduct’swarrantyme.Thewarrantyincludestherepairofadefec-

ve partordevice, orifneeded, anew partordevice, but not installaon or

exchangecosts.Undernocircumstanceisthesellerliablefordamagescompen-

saonforindirectdamage.

4x0001 Manufacturer 16bit 0...7 0...7

4x0002 Formulaunit(Manufacturer=7) 16bit 0...5 0=m3/s,1=m3/h,2=cfm,

3=l/s,4=m/s,5=f/min

4x0003 K-factorintegral 16bit 0...9999 0...9999

4x0004 K-factordecimal 16bit 0...999 0...999

4x0005 Responseme 16bit 0...20 0...20s

4x0006 PIDcontrolunit 16bit 0...1 0...1

4x0007 PIDpressureref 16bit 0...2500 0...2500

4x0008 PIDowrefinteger 16bit 0...30000 0...30000

4x0009 PIDowrefdecimal 16bit 0...999 0...999

4x0010 PIDpvalue 16bit 0...10000 0...10000

4x0011 PIDiinteger 16bit 0...1000 0...1000

4x0012 PIDidecimal 16bit 0...99 0...99

4x0013 PIDdinteger 16bit 0...1000 0...1000

4x0014 PIDddecimal 16bit 0...99 0...99

4x0015 Overdrivevalue 16bit 0...100 0...100%

4x0016 Overdriveacve 16bit 0...1 0...1

4x0017 Temperaturecompensaon 16bit 0…1 0=o,1=on

4x0018 Temp.comp.startTE 16bit -45…50 -45…50°C

4x0019 Temp.comp.stopTE 16bit -50…45 -50…45°C

4x0020 Temp.comp.dropintegerpart 16bit 0…99 0…99%

4x0021 Temp.comp.dropdecimalpart 16bit 0…999 0.0…0.999%

Funconcode03-Readinputholdingregister

Funconcode05-Writesinglecoil

0x0001 Zeroingfuncon Bit0 0...1 On-O

Thepartsleoverfrominstallaonshouldberecycled

accordingtoyourlocalinstrucons.Decommissioned

devicesshouldbetakentoarecyclingsitethatspecial-

izesinelectronicwaste.

STEP 8: MODBUS REGISTERS

RECYCLING/DISPOSAL

WARRANTY POLICY

Funconcode02-Readinputstatus

1x0001 Input:BININ Bit0 0...1 On-O

MODBUS REGISTERS CONTINUED

STEP 7: Fixed output

Fixedoutputsengscanbeenabledtosetthecontroloutputtoapresetvalue.

Primarypurposeofthisfunconalityistoenabletheadjustmentofairvalves

andterminalswithouttheDPT-Ctrlaecngtheductpressureorairow.Itcan

alsoaidintroubleshoongtheinstallaon.

1)Toenablethexedoutput,scrolltoitsposioninthemenu.

2)Presstheselectbuonandselectthedesiredxedoutputvalue.The

outputwillnowstayatthisvalueindenitely.Innormaloperaonmode

(shownbelow),theupperrowofthedisplaywillshowFIXEDxx%to

indicatetheoutputisxed.

FIXED OUTPUT

OFF

SELECT

DOWN

FIXED 50 %

184 Pa

3)Toenablethenormalcontroloutputanddisablethexedoutput,scrollto

itsposion,selectitandsetvaluetoOFF.

FixedoutputfunconisalsoavailableviaModbus.(4x0016:Overdriveacve,

4x0015:Overdrivevalue)

Funconcode04-Readinputregister

3x0001 Programversion 16bit 0...1000 100...9900

3x0002 PressurereadingA 16bit -250...2500 -250...2500Pa

3x0003 Input0...10V 16bit 0...100 0...100%

3x0004 InputPT1000 16bit -500...500 -50...+50°C

3x0005 InputNi1000 16bit -500...500 -50...+50°C

3x0006 InputNi1000-LG 16bit -500...500 -50...+50°C

3x0007 InputNTC10k 16bit -500...500 -50...+50°C

3x0008 Flowm3/s 16bit 0...10000 0...100m3/s

3x0009 Flowm3/h 16bit 0...30000 0...30000m3/h

3x0010 Flowcfm 16bit 0...30000 0...30000cfm

3x0011 Flowl/s 16bit 0...3000 0...3000l/s

3x0012 Velocitym/s 16bit 0...1000 0...100m/s

3x0013 Velocityf/min 16bit 0...5000 0...5000f/min

Otros manuales de Transmisor de HK Instruments

HK Instruments

HK Instruments CDT-MOD-2000 Duct Series Manual de usuario

HK Instruments

HK Instruments AVT Series Manual de usuario

HK Instruments

HK Instruments DPT-Priima Series Manual de usuario

HK Instruments

HK Instruments RHT-MOD Duct Series Manual de usuario

HK Instruments

HK Instruments AVT Series Manual de usuario

HK Instruments

HK Instruments DPT-MOD Series Manual de usuario

HK Instruments

HK Instruments DPT-MOD Series Manual de usuario

HK Instruments

HK Instruments Siro-MOD Series Manual de usuario

HK Instruments

HK Instruments CDT2000 Series Manual de usuario

HK Instruments

HK Instruments CDT Series Manual de usuario

HK Instruments

HK Instruments RHT DUCT Series Manual de usuario

HK Instruments

HK Instruments DPT Series Manual de usuario

HK Instruments

HK Instruments RHT-MOD Duct Series Manual de usuario

HK Instruments

HK Instruments RHT-MOD Series Manual de usuario

HK Instruments

HK Instruments DPT-Priima Series Manual de usuario

HK Instruments

HK Instruments CMT Series Manual de usuario

HK Instruments

HK Instruments DPT-CR-MOD Series Manual de usuario

HK Instruments

HK Instruments DPT-Flow-1000 Guía de inicio rápido

HK Instruments

HK Instruments SIRO Series Manual de usuario

HK Instruments

HK Instruments DPT-2W- 100-R2 Manual de usuario

HK Instruments

HK Instruments DPT-2W- 100-R2 Manual de usuario

HK Instruments

HK Instruments DPT-Priima Series Manual de usuario

HK Instruments

HK Instruments DPT-MOD Series Manual de usuario

HK Instruments

HK Instruments RHT-MOD Duct Series Manual de usuario

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario