Copyright HK Instruments Installation Version 1.0 2012
1. Switching point (display required)
• Install jumper to pins labeled sw.p. (switching point).
(See Figure 5)
• Press down on the pushbutton (joystick) to select the switching
point of the relay. The chosen value (fpm) is shown on the display.
• Remove and store the jumper after the conguration is
completed.
2. Hysteresis (display required)
• Install jumper to pins labeled hyst. (hysteresis).
(See Figure 5)
• Press down on the pushbutton (joystick) to select the hysteresis of
the relay switching point. The chosen value (fpm) is shown on the
display.
• Remove and store the jumper after the conguration is
completed.
FIGURE 3CONFIGURING THE RELAY RELAY MODE ONLY STEP 4
Figure 5
T
v
V mA
sw.p.
hyst.
Tout
vout
24V
GND
J1
J2
Push Button
See Dimensional Drawing Above
FIGURE 3WARRANTY POLICY
(a) WARRANTY COVERAGE: HK warrants to the original end user
of the Products that the Products will, at the date of initial
purchase, meet the applicable specication for such Products (as
described by HK in its product literature) and, under normal use
and service, will be free from any defects in materials or manufac-
ture for (a) one (1) year from date of sale to end user for electrome-
chanical Products and (b) ve (5) years from date of manufacture
for electronic Products.
(b) NO WARRANTY OF PRODUCT SUITABILITY: Neither HK nor
the manufacturer of the Products to be sold hereunder
(“Manufacturer”) makes any warranty that Products are suitable for
a particular purpose, application or design. Many states and
localities have differing codes or regulations governing the installa-
tion and/or use of HK products. HK does not guarantee compli-
ance with such codes or regulations; the end user is solely
responsible for safe and correct installation and use of the Prod-
ucts and for compliance with such codes and regulations.
(c) EXCLUSION OF IMPLIED WARRANTIES: THE WARRANTY
HEREIN IS THE ONLY WARRANTY APPLICABLE TO THE PROD-
UCTS AND EXCLUDES ALL OTHER WARRANTIES, INCLUDING
ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, AND ANY IMPLIED WARRANTY ARIS-
ING FROM COURSE OF DEALING OR USAGE OF TRADE.
(d) REMEDIES FOR NON-CONFORMITY OR BREACH OF WAR-
RANTY: If the Product purchased does not conform to the appli-
cable warranty, HK will provide, at its option, one of the following
remedies: (1) repair of the non-conforming Product, (2) replace-
ment with a conforming Product, or (3) refund of the original
purchase price. THESE REMEDIES SHALL BE THE EXCLUSIVE
AND SOLE REMEDY for any breach of warranty. HK and Manufac-
turer have no other responsibility or liability for breach of warranty
or otherwise.
(e) LIMITATION OF LIABILITY: NEITHER HK NOR MANUFAC-
TURER WILL BE LIABLE FOR ANY INCIDENTAL, SPECIAL,
INDIRECT, OR CONSEQUENTIAL DAMAGES UNDER ANY
CIRCUMSTANCE, INCLUDING WITHOUT LIMITATION ANY
DEFECT IN THE PRODUCT PURCHASED.
(f) FURTHER LIMITATIONS: The warranty herein does not cover
damage caused by lightning, ood or other natural phenomenon;
normal wear and tear; accident, improper or careless handling,
abnormal use, overloading, improper storage or abuse; incorrect
installation, care or reconstruction; or alteration, calibration,
reconguration, maintenance or installation work done by unquali-
ed personnel. Should Manufacturer alter the structure of any
Product in the future, HK and Manufacturer shall not be obligated
to make comparable changes to Products already purchased. HK
will give a new warranty for Products being replaced or repaired
within the warranty period, however only to the expiration of the
original Product’s warranty period. The warranty includes the repair
of a defective part or device, or if needed, a new part or device,
but no other costs except as otherwise stated in the HK Distributor
Terms and Conditions.
