Hitachi RAR-M0A5 Manual de usuario
– 1 –
Instruction manual Page 1~26
To obtain the best performance, please read this instruction manual completely.
คู่มือการใช้งาน หน ้า 27~54
เพือได ้รับการทํางานทีดีทีสุด โปรดอ่านคู่มืออย่างละเอียด
REMOTE
CONTROLLER
MANUAL
<A>
คู่มือการใช้งานหน้า
– 2 –
NAMES AND FUNCTIONS OF REMOTE CONTROL UNIT
REMOTE CONTROLLER
This controls the operation of the indoor unit. Signal range to reach indoor unit is about 7 meters. If
inverter lamp is used, the range of control may be shorter.
This unit can be fixed on a wall using the fixture provided. Before fixing it, make sure the indoor unit
can be controlled from the remote controller.
●Transmission sign
The transmission sign blinks when a signal is sent.
●Display
This indicates the room temperature selected, timer status, function
and intensity of circulation selected.
●AIR SLEEP TIMER button
Use this button to set the air sleep timer mode.
●TEMPERATURE button
Use this button to raise or lower the temperature setting. (Keep pressed,
and the value will change more quickly.)
●START/STOP button
Press this button to start or to stop operation.
●FAN SPEED selector button
This determines the fan speed. Each time you press this button, the
intensity of circulation will change from (AUTO) ➞(HI)
➞(MED) ➞(LOW).
●AUTO SWING button
Controls the angle of the horizontal air deflector.
●ONE TOUCH POWERFUL buttonA
Use this button to deliver faster and more comfortable air-conditioning
or start operation.T
●RESET button
●MODE selector button
Use this button to select MODE. Each time you press this button the
MODE selection will change from (COOLING) ➞(SILENT)
➞(DEHUMIDIFY) ➞(FAN).
However, during OFF mode SILENT will be skipped.
●OFF-TIMER button
Select to turn OFF time.
●ON-TIMER button
Select to turn ON time.
Precautions for Use
●Do not put the remote controller in the following places.
●In direct sunlight.
●In the vicinity of a heater.
●Handle the remote controller carefully. Do not drop it on the
floor, and protect it from water.
●Once the outdoor unit stops, it will not restart for about 3
minutes (unless you turn the power switch off and on or unplug
the power cord and plug it in again).
This is to protect the device and does not indicate a failure.
– 3 –
Use the device for cooling when the outdoor temperature is 21 ~ 43°C.
If indoors humidity is very high (over 80%), some dew may form on the air outlet grille of the indoor unit.
Press the selector button so that the display indicates
(COOL).
Set the desired FAN SPEED with the button (the display
indicates the setting).
(AUTO) : The FAN SPEED is HI at first and varies to
MED or LOW automatically when the preset
temperature has been reached.
(HI) : High fan speed.
(MED) : Medium fan speed.
(LOW) : Low fan speed.
Set the desired room temperature with the TEMPERATURE button
(the display indicates the setting).
The range of 25 ~ 28°C is recommended as the
room temperature for cooling.
If the temperature setting is 27°C, the room
temperature will be controlled at around 27°C.
The temperature setting and the actual room temperature may
vary somewhat depending on conditions.
■As the settings are stored in memory of the remote controller, you only
have to press the (START/STOP) button to repeat the same
settings next time.
1
2
START
3
COOLING OPERATION
HI fan speed mode selected
When unit has been operating for a long period of time and the difference between remote controller
setting temperature and actual room temperature is continuously large, the fan speed may increase causing
higher air blow sound.
During the time, cooling capacity will be maximized. If the air blow sound causes any discomfort, please
select “AUTO” or other than “HI” fan speed.
NOTE
Press the button. Cooling operation starts with a beep.
Press the button again to stop the operation.
– 4 –
SILENT OPERATION
During Cooling mode, press the selector button so that
the display indicates (SILENT) along with the (COOL)
symbol. Silent operation starts with a beep.
1
CANCELLATION of SILENT Operation
Cancel Condition Operation mode after cancel
Key press
Key press
Key press
Key press
Stop operation
Selected mode operation
(COOLING) (SILENT)
(FAN) (DEHUMIDIFY)
COOLING operation in previous setting
POWERFUL operation
NOTE:
Under SILENT mode operation and quiet environment, phenomena like flowing noise of refrigerant in the
refrigerating cycle may occur, but this is normal for the operation.
– 5 –
DEHUMIDIFYING OPERATION
Use the device for dehumidifying when the room temperature is over 16°C.
When it is under 15°C, the dehumidifying function will not work.
■Dehumidifying Function
When the room temperature is higher than the temperature setting: The device will dehumidify the room
and reducing the room temperature to the preset level.
When the room temperature is lower than the temperature setting: Dehumidifying will be performed at the
temperature setting slightly lower than the current room temperature, regardless of the temperature setting.
The function will stop (the indoor unit will stop emitting air) as soon as the room temperature becomes lower
than the setting temperature. You might feel a bit colder in dehumidifying operation.
■As the settings are stored in memory in the remote controller, you
only have to select (DEHUMIDIFY) then press the
button next time.
Set the desired room temperature with the TEMPERATURE
button (the display indicates the setting).
The range of 20 ~ 26˚C is recommended as
the room temperature for dehumidifying.
Press the selector button so that the display indicates
(DEHUMIDIFY).
The FAN SPEED is set at LOW automatically.
The FAN SPEED button does not work during DEHUMIDIFY
operation.
Press the button. Dehumidifying operation starts with
a beep. Press the button again to stop the operation.
START
2
1
– 6 –
FAN OPERATION
Press the selector button so that the display indicates
(FAN).
■As the settings are stored in memory in the remote controller, you
only have to select (FAN) then press the
button next time.
Press the button. Fan operation starts with a beep.
Press the button again to stop the operation.
START
1
2
Set the desired FAN SPEED with the button.
(the display indicates the selectable setting).
(HI) : High fan speed.
(MED) : Medium fan speed.
(LOW) : Low fan speed.
In Fan operation mode the device is function as an air circulator.
■FAN Function
During FAN operation, compressor does not run and there is no cooling operation with only indoor fan running.
– 7 –
ONE-TOUCH POWERFUL MODE
Press the button.
●Operation start with a signal received sound “beep”.
●Unit will be forced operate in (COOL) with POWERFUL
MODE fan speed for 20 minutes, within this 20 minutes, fan speed
may varies. Indicator appear during this period. (Operation
lamp at indoor unit is blinking).
●After 20 minutes, operation lamp stop blinking and indicator
will disappear while unit will be in previous mode setting.
●Air blow sound will be slightly high due to forced operation.
1
CANCELLATION of POWERFUL Operation
If feeling so cold,
cancel this powerful
mode as mentioned in
“CANCELLATION of
POWERFUL operation”.
Cancel Condition Operation mode after cancel
Key press
Key press
Key press
Press or
Press or
20 minutes time is up
Press or
Stop operation
Selected mode operation
(COOLING) (SILENT)
(FAN) (DEHUMIDIFY)
AIR SLEEP TIMER operation
COOLING operation in previous setting
– 8 –
HOW TO SET THE AIR SLEEP TIMER
Press the button, and the display changes as shown below.
Mode
Air Sleep Timer
Indication
Air Sleep Timer: The device will continue working for the
designated number of hours and then turn off.
Point the signal window of the remote controller toward the indoor
unit, and press the AIR SLEEP TIMER button.
The timer information will be displayed on the remote controller.
The TIMER lamp lights with a beep from the indoor unit.
Cooling
“ ” ,
Silent
“ ”
and
Dehumidifying
“ ”
Explanation of the air sleep timer
The device will control the FAN SPEED and room temperature automatically so as to be quiet
and good for people’s health.
You can set the sleep timer to turn off after 1,2,3 --
➞
9 or 10 hours. The FAN SPEED and
room temperature will be controlled as shown below.
Function Operation
The room temperature will be
controlled 2°C above the setting
temperature and the FAN SPEED
will be set to LOWEST 1 hour
after the setting of the air sleep
timer.
Air Sleep
Timer
Operation with the air sleep timer
– 9 –
HOW TO SET THE TIMER
■ON Timer and OFF Timer are available.
OFF TIME setting
●Select the OFF TIME by pressing the (OFF TIMER)
Button.
●Setting time will change according to the below sequence
when you press the button.
OFF Timer Reservation ■Operation stop at setting time
ON TIME setting
●Select the ON TIMER by pressing the (ON
TIMER) Button.
●Setting time will change according to the below
sequence.
ON Timer Reservation ■Operation will start for setting
temperature at setting time.
●After the OFF TIMER is set, the hour display will be counting
down as time passes.
●After the ON TIMER is set, the hour display will be counting
down as time passes.
– 10 –
AIR FLOW LOUVERS ADJUSTMENTS
1
2Adjustment of the conditioned air to the left and right.
Hold the second vertical air deflector of each set of vertical
air deflectors from right as shown in the figure and adjust the
conditioned air to the left or right.
●If the “ (AUTO SWING)” button is pressed
once, the horizontal air deflector swings up and down.
If the button is pressed again, the deflector stops in its
current position. Several seconds (about 6 seconds) may
be required before the deflector starts to move.
●Use the horizontal air deflector within the adjusting range
shown on the right.
●When the operation is stopped, the horizontal air deflector
moves and stops at the position where the air outlet
closes.
!CAUTION
●In “Cooling” operation, do not keep the horizontal air
deflector swinging for a long time. Some dew may form
on the horizontal air deflector and dew may drop.
Adjustment of the conditioned air in the upward and downward
directions.
The horizontal air deflector is automatically set to the proper
angle suitable for each operation. The deflector can be swung
up and down continuously and also set to the desired angle
using the “ (AUTO SWING)” button.
A
Do not insert a finger, a rod or other objects into the air outlet or inlet as the fan is rotating at a high speed,
it will cause injury. Before any cleaning or adjusting the deflectors, be sure to switch OFF the operation.
!
WARNING
Tabla de contenidos
Idiomas:
Otros manuales de Mando a distancia de Hitachi
Hitachi
Hitachi SPX-RCDA Manual de usuario
Hitachi
Hitachi SPX-RCKA Manual de usuario
Hitachi
Hitachi RAR-5F Manual de usuario
Hitachi
Hitachi ECO COMPACT PC-ARC-E Manual de usuario
Hitachi
Hitachi RAR-5F1 Manual de usuario
Hitachi
Hitachi airPoint Room700 Manual de usuario
Hitachi
Hitachi PC-ARFHE-02 Manual de usuario
Hitachi
Hitachi PC-ARFP1E Manual de usuario
Hitachi
Hitachi PC-ARFLE Manual de usuario
Hitachi
Hitachi RAR-6N2 Manual de usuario
Hitachi
Hitachi PC-ARFG1-A Manual de usuario
Hitachi
Hitachi PC-ARFP1E Manual de usuario
Hitachi
Hitachi RAK-70PPD Manual de usuario
Hitachi
Hitachi REMOTE OPERATOR WOP Manual de usuario
Hitachi
Hitachi RAR-5J1 Manual de usuario
Hitachi
Hitachi SPX-RCKA2 Manual de usuario
Hitachi
Hitachi PC-ARFH1E-03 Manual de usuario
Hitachi
Hitachi PC-ARFG2-Z Manual de instrucciones
Hitachi
Hitachi PC-ARFPE Manual de usuario
Hitachi
Hitachi RAR-7PE1 Manual de usuario
