Hirschmann PAT IFLEX5 Manual de usuario

HIRSCHMANN

P/N 031-300-190-147 REV E- 11/12/2008

LOAD MOMENT INDICATOR

iFLEX5

vertical/horizontal console

OPERATOR’S MANUAL

NOTICE

PAT America, Inc. makes no warranty of any kind with regard to this material, including, but not limited

to, the implied warranties of merchantability and/or its fitness for a particular purpose.

PAT America, Inc. will not be liable for errors contained in this manual or for incidental or

consequential damages in connection with the furnishing, performance, or use of this manual. This

document contains proprietary information, which is protected by copyright, and all rights are reserved.

No part of this document may be photocopied, reproduced, or translated to another language without

the prior written consent of PAT America, Inc.

PAT America, Inc. reserves proprietary rights to all drawings, photos and the data contained therein.

The drawings, photos and data are confidential and cannot be used or reproduced without the written

consent of PAT America, Inc. The drawings and/or photos are subject to technical modification

without prior notice.

All information in this document is subject to change without notice.

MANUAL REVISIONS

REV DATE NAME DESCRIPTION

- 2/22/02 MO ECN 02-64

A 11/11/02 CH ECN 02-278

B 05/19/03 SB ECN 03-065

C 02/22/05 MS ECN 05-041

D 01/06/06 SB ECN 05-217

E 11/12/08 WG ECN 08-179

Operator's Manual iFLEX5

TABLE OF CONTENTS

1GENERAL INFORMATION.............................................................................................................1

2WARNINGS.....................................................................................................................................1

3SYSTEM DESCRIPTION ................................................................................................................2

3.1 SYSTEM FUNCTION ........................................................................................................................4

3.2 OPERATING CONSOLE ...................................................................................................................5

3.3 CONTROL IDENTIFICATION..............................................................................................................5

4CONFIGURATION SETUP ........................................................................................................... 11

4.1 LMI SETUP PROCEDURE..............................................................................................................11

4.2 QUICK SETTING OF THE REEVING.................................................................................................15

4.3 QUICK HOIST LINE SELECTION.....................................................................................................16

5OPERATION .................................................................................................................................17

5.1 LIMIT SETTING.............................................................................................................................20

5.1.1 Slewing Angle Limitation / Work Area Definition...........................................................21

5.1.2 Tip Height Limitation ........................................................................................................26

5.1.3 Boom Angle Limitation.....................................................................................................27

5.1.4 Radius Limitation..............................................................................................................29

5.1.5 Wind Speed .......................................................................................................................30

5.2 INFO CRANE CONFIGURATION ......................................................................................................31

5.3 DISPLAY CONTRAST CONTROL.....................................................................................................32

6PRE-OPERATION INSPECTION AND CALIBRATION VERIFICATION.....................................33

6.1 MACHINES WITH ONLY A MAIN HOIST............................................................................................33

6.2 MACHINES WITH MAIN AND AUXILIARY HOISTS .............................................................................33

6.3 INSTALLATION OF ANTI TWO-BLOCK RETAINER IN LOCKING POSITION ..........................................34

6.4 REMOVAL AND STORAGE OF THE ANTI TWO-BLOCK RETAINER.....................................................34

6.5 PRE-OPERATION INSPECTION AND CALIBRATION VERIFICATION ....................................................35

7SERVICE AND MAINTENANCE...................................................................................................36

8TROUBLESHOOTING ..................................................................................................................37

8.1 GENERAL ....................................................................................................................................37

8.2 MALFUNCTION TABLE ..................................................................................................................37

8.3 OPERATING ERRORS ...................................................................................................................38

9APPENDIX A: DETAILED SYMBOL EXPLANATION OF BOOM EXTENSIONS .......................40

10 APPENDIX B:DETAILED SYMBOL EXPLANATION OF COUNTERWEIGHT OPTIONS.......41

General Information

1 GENERAL INFORMATION

The PAT Load Moment Indicator1(LMI) has been designed to provide the crane operator with

the essential information required to operate the machine within its design parameters.

Using different sensing devices, the Load Moment Indicator monitors various crane functions

and provides the operator with a continuous reading of the crane’s capacity. The readings

continuously change as the crane moves through the motions needed to make the lift.

The LMI provides the operator with information regarding the length and angle of the boom,

working radius, rated load and the total calculated weight being lifted by the crane.

If non permitted conditions are approached, the Load Moment Indicator will warn the operator

by sounding an audible alarm, lighting a warning light and locking out those functions that may

aggravate the crane’s condition.

2 WARNINGS

The LMI is an operational aid that warns a crane operator of approaching overload conditions

and of overhoist conditions that could cause damage to equipment and personnel.

The device is not, and shall not, be a substitute for good operator judgment, experience and use

of accepted safe crane operating procedures.

The responsibility for the safe crane operation shall remain with the crane operator who shall

ensure that all warnings and instructions supplied are fully understood and observed.

Prior to operating the crane, the operator must carefully and thoroughly read and understand

the information in this manual to ensure that he knows the operation and limitations of indicator

and crane.

Proper functioning depends upon proper daily inspection and observance of the operating

instructions set forth in this manual. Refer to Section 6. Pre-Operation Inspection and

Calibration Verification of this handbook.

The LMI can only work correctly, if all adjustments have been properly set. For correct

adjustment, the operator has to answer thoroughly and correctly all questions asked

during the setup procedure in accordance with the real rigging state of the crane. To

prevent material damage and serious or even fatal accidents, the correct adjustment

of the LMI has to be ensured before starting the crane operation.

1LOAD MOMENT: generally the product of a force and its moment arm; specifically, the product of the load and the load-radius. Used in the

determination of the lifting capacity of a crane

Operator's Manual iFLEX5

3 SYSTEM DESCRIPTION

The PAT Load Moment Indicator consists of a central micro processor unit, operating console,

length/angle sensor, pressure transducers, and anti-two block switches.

The system operates on the principle of reference/real comparison. The real value, resulting

from the pressure measurement is compared with the reference data, stored in the central

processor memory and evaluated in the micro processor. When limits are reached, an overload

warning signal is generated at the operator’s console. At the same time, the aggravating crane

movements, such as hoist up, telescope out and boom down, will be stopped.

The fixed data regarding the crane, such as capacity charts, boom weights, centers of gravity

and dimensions are stored in memory chips in the central processor unit. This data is the

reference information used to calculate the operating conditions.

Boom length and boom angle are registered by the length/angle sensor, mounted inside the

cable reel which is mounted on the boom. The boom length is measured by the cable reel cable

which also serves as an electrical conductor for the anti two-block switches.

The crane load is measured by pressure transducers attached to the piston and rod side of the

hoist cylinders.

The interactive user guidance considerably simplifies the input of operating modes as well as

the setting of geometry limit values.

System Description

Fig. 1: Components of the LMI system PAT iFLEX5

1 Central-Micro-Processor Unit

2 Operating Console

3 Pressure Transducers

4 Length/Angle Sensor

5 Anti Two-Block Switch(es)

POWER

LOCKOUT

OTHER

PAT

Operator's Manual iFLEX5

3.1 SYSTEM FUNCTION

Upon switching on, the system starts with an

automatic test of the LMI system, of lamps

and audible alarm. During the test, the LC

display shows the initial logo.

If the system was turned off for more than

two hours, the setup configuration has to be

entered after the system test. (⇒chapter 4)

First, the operating mode is determined by

an interactive step-by-step interrogation of

the rigging states.

Next is the interactive input of the reeving.

Now the LC display shows in symbols all

inputs and awaits acknowledgment or

canceling.

Upon acknowledgment of the inputs the

system is ready for operation.

Otros manuales para PAT IFLEX5

Tabla de contenidos

Otros manuales de Mezclador de música de Hirschmann

Hirschmann

Hirschmann iSCOUT expert compact Manual de usuario

Hirschmann

Hirschmann PRS 35 EZ Manual de usuario

Hirschmann

Hirschmann PRS 40 EZ Manual de funcionamiento

Hirschmann

Hirschmann Manitex vSCALE D3 Manual de usuario

Hirschmann

Hirschmann PAT 050-350-061-351 Guía

Manuales populares de Mezclador de música de otras marcas

Neve

Neve 8816 Manual de usuario

Mackie

Mackie Onyx Analogue Mixer Manual de usuario

Behringer

Behringer EUROPOWER PMP518M Manual de usuario

Peavey

Peavey S-32 Sanctuary Series Manual de usuario

Rane

Rane MP 4 Manual de usuario

True

True T9 Touchscreen Console Manual de usuario

Studiomaster

Studiomaster Air Pro 24 Manual de usuario

Pioneer

Pioneer SVM 1000 - Audio/Video Mixer Manual de usuario

Roland

Roland M-160 Manual de usuario

Yamaha

Yamaha MR1642 Manual de usuario

Ecler

Ecler MAC40v Manual de usuario

Pioneer

Pioneer DJM 909 - Battle Mixer W/Effects Manual de usuario

Veeder-Root

Veeder-Root TLS-350 Series Manual de usuario

Alto

Alto APM80.QUAD Manual de usuario

Omnitronic

Omnitronic PM-211 Manual de usuario

SoundCraft

SoundCraft B400 Manual de usuario

Roland

Roland SoundCanvas SC-8820 Manual de usuario

CARVIN

CARVIN RX 1200 Manual de usuario