HIOS BLG-BC1 Series Manual de usuario

■Cunter Display Section

Pass Light

M Light

Fail Light

Function Display Section

Screw Fastening

Count Display Section

Function Display Section

F1 Button

F3 Button

F2 Button

(1)

Screw Fastening Count Display Section/Set Value Display Section

●Inthenormalmode,thescrewfasteningcountsetvalueis

displayedrst,andafterstartingthecount,theremaining

screwfasteningcountisdisplayed.

●Thecountdecreaseswitheachscrewfasteningoperation

andtheremainingscrewfasteningcountisdisplayed.

(2) Function Display Section

●Thesymbolcorrespondingtothesetitemisdisplayedinthe

settingmode.

(3) F1 Button

●Whenthisbuttonispressedformorethan2secondinthe

normalmode,themodeischangedtothesettingmode.

●

Thisbuttonisusedforselectingthefunctioninthesetting

mode.

●Whenthisbuttonispressedformorethan2secondinthe

settingmode,thebuzzersoundstwiceandthemodeis

changedtothenormalmode.

(4)F2,F3Button

●Usingthesebuttons,thesetvaluecanbechangedinthe

functionsetting.

Somesetvaluesarelimiteddependingonthefunctiontobeset.

(5) Pass Light*

●

Whenthescrewfasteningresultis“OK”,thegreenLEDlightturnsON.

(6) Fail Light*

●

Whenthescrewfasteningresultis“NG”,theredLEDlightturnsON.

■Other Operations

■Precautions in the Unit Operation

●WhenthisunitisusedincombinationwiththeexistingHIOS

externalcounter,thedrivercounterdoesnotsynchronizedwith

theexternalcounter.So,usethembasedontheexternalcounter

function.

Otherwise,turnoffthedriver’scountingfunctionbeforeuse.

・

CombinationAvailablewithExternalCounterModelsPowerUnit

BLOP-STC3withtheScrewCounter

SeparateCounterBLOP-SC1

●WhentheoutputsettingforPowerHI/LOWischanged,thedriver

speedchanges.Insuchcases,payattentiontothecountertimer

setvalueandreversecountertimersetvalue.

●Appropriateoperationenvironment.

・

Donotusetheunitinanenvironmentwheretheambient

temperatureisoutsidetherangeof+5to40ºC.

・

Inanareawithstaticelectricity,usethisunitonlyafterremoving

thestaticelectricity.

Thecountistobereturnedto

thedefaultvalueduringthe

screwfasteningoperation.

PressingtheF3Buttonfor2secondsor

more,resetsthescrewfasteningcount

value.

HowtochecktheCounter

TimerSetTime.

Whenthescrewisfastenedforthetime

period(second)setusingthecounter

timer:

●Forcorrectoperation,thebuzzer

soundsonce.

●Forincorrectoperation,thebuzzerdoes

notsound.

Whenthebuzzerdoesnotsound,

increasesthesetvaluegraduallyand

adjustsitsothatthebuzzersounds

once.

Theconrmationwiththebuzzer

soundisusefulforpreventingascrew

fasteningerror.

LockFButtons. 1.SlidetheFOR/REVswitchtoFOR.

2.Idleforabout20seconds.

→"M"lightisturnedon,andthebuttons

arelocked.

Theywillbeunlockedifyouredothe

abovesteps.

Brushless®Screwdriver

withbuilt-inScrewCounter

BLG-BC1 Series

INSTRUCTIONMANUAL

(July2018)

No.ET-A011-BC118B

■Features

●OPC(outputsignals)isavailable.

WhenthedriverisconnectedtotheHIOSrelaybox

“BLOP-AF”,anexternaldevicesuchasasequencer,a

revolvinglightorabuzzercanbeusedtovisualizethe

screwfasteningoperationwiththesignals.

●

Thisunitcanbeusedalsoasanormaldriverwiththe

countingfunctioncancelled.ThedisplayisalsoOFF.

●

Thedriver,runningwithoutfasteningthescrew,orreverse

turning,isnotcounted.

●

Screwfasteningerrorscanbedetectedwitheasyoperation

andsetting.

*Ifyourunthedriver,thepassofFailOFF.

HIOS Inc.

1-16-5Akiyama,MatsudoCity,ChibaPref.,Japan270-2223

TEL:+81-47-392-2001FAX:+81-47-392-7773

■Setting Function List

Dis-

play

Setting Function

<DefaultValue>

Symbol

Setting Description

(1) Counter

ON/OFFSetting

:Whenselected,thecounterfunction

isavailable.

:Whenselected,itisusedasa

normaldriver.

ThedisplayisalsoOFF.

(2) Count Thescrewfasteningcountvalueisset.

SettingRange:1to99

(3) CountTimer Thisfunctionisusedtopreventthecount

fordoubletighteningoperationssuchas

checkfasteningorretightening.

Settheoperationtimewhilethecheck

fasteningisperformedforthetightenedscrew.

SettingRange:0.00to0.99seconds

Note: Whenthescrewtighteningoperation

isperformedduringsettingand

thejudgmentresultisnormal,the

buzzersoundsonce.

(4) Work Reset Timer Thebuzzersoundtimeperiodafterthe

workiscompletedisset.

SettingRange:0.0to3.9seconds

Note:Setitbasedonthereversecount

timersetvalue.

(5) ReverseCount

Timer

Thetimeperioduntilthereversecount

isperformedisset.Settheworkreset

timeroperationtimebasedonthetime

perioduptowhenthereversecountis

performed.

SettingRange:0.1to1.0seconds

Note:Itisavailablewhenthe“Reverse

CountEnable”hasbeensetinthe

systemsetting.

(6) SystemSetting EachBuzzerorReverseCountEnable/

Disableissetup.

Thesettingisperformedwitha

combinationofthetensdigitandsingle

unitdigit.

TensDigit

0:BuzzerEnable/ReverseCountEnable

1:BuzzerEnable/ReverseCountDisable

2:BuzzerDisable/ReverseCountEnable

3:BuzzerDisable/ReverseCountDisable

UnitsDigit

2:TorqueUpBuzzerDisable

3:TorqueUpBuzzerEnable

(7) OverTime/

ShortTime

ThissetswhetherornottheOverTime/

ShortTimeerrorisdetected.

0:Whenselected,neitherOverTimeor

ShortTimeErrorisdetected.

1:Whenselected,onlytheShortTime

Errorisdetected.

2:Whenselected,onlytheOverTime

Errorisdetected.

3:Whenselected,thebothOverTime/

ShortTimeErroraredetected.

Dis-

play

Setting Function

<DefaultValue>

Symbol

Setting Description

(8) Accumulated

Counter

Theaccumulatedcountofthescrew

fasteningoperationisdisplayed.

Fortheaccumulatedcount,allthetorque-

upoperationsarecountedregardlessof

whetherthecounterisON/OFF.

Display Howtoreadthedisplay

UnitsDigit:Numberedinmultiples

of100,000shots

TensDigit:Numberedinmillions

ofshots

■Operation

ChangingtotheSettingMode

PresstheF1Buttonformorethan2secondsinthenormalmode.

“P”willbedisplayedinthefunctiondisplaysectionandthemodewillbe

changedtothesettingmode.

SettingMode

EachpressingoftheF1Buttoninthesettingmodechangesthesetting

item.Referto“SettingFunctionList”forthesettingfunctiondetails.

(Count)

(Count Timer)

(Work Reset Timer)

(Reverse Count Timer)

(System Setting)

(Over Time/Short Time) (Accumulated Counter)

ChangingtotheNormalMode

PresstheF1Buttonformorethan2secondsinthesettingmode.

Themodewillbechangedtothenormalmodeandthevaluesetfor

thecountwillbedisplayed.

●CounterON/OFFSetting

EachpressingoftheF3ButtontogglesONandOFF.

(Note:F2Buttonisnottobeused.)

●ValueSettingforEachFunction

1.EachpressingoftheF2Buttoninthesettingmode

changesthegurepositionforsetting.

2.EachpressingoftheF3Buttonincreasesthevalueoneby

one.

Note:Thesettingprocedureisthesameforallthesettings

exceptforthe“CounterON/OFFSetting”.

 Referto“■SettingFunctionList”forthesettingrange.

Otros manuales para BLG-BC1 Series

Tabla de contenidos

Otros manuales de Contador de efectivo de HIOS

HIOS

HIOS SC1 Series Manual de usuario

Manuales populares de Contador de efectivo de otras marcas

Omron

Omron H7CL Series Manual de usuario

FAAC

FAAC XTR B Manual de usuario

Olympia

Olympia NC-350A Series Manual de usuario

Evco

Evco EV7001 Manual de usuario

Record

Record FlowControl Manual de usuario

XIA

XIA UltraLo-1800 Manual de usuario

Cashmaster

Cashmaster Sigma 105 Manual de usuario

Agilent Technologies

Agilent Technologies 53151A Manual de usuario

Cashmaster

Cashmaster Sigma 105 Manual de usuario

Tellermate

Tellermate TY Manual de uso y cuidado

HYOSUNG

HYOSUNG MX-4000W Manual de usuario

Cashmaster

Cashmaster Sigma 105 Manual de usuario

CCE

CCE 3200 Manual de usuario

HP 53150A Series Instrucciones de funcionamiento

HYOSUNG

HYOSUNG 1800CE Manual de usuario

MZ electronic

MZ electronic EV-040 Manual de usuario

Delfield

Delfield Shelleysteel SCFM-50 Manual de usuario

TSI Instruments

TSI Instruments AEROTRAK+ 7201 Manual de usuario