Hilti PD 5 Manual técnico

PD 5

English en

Français fr

Español es

Printed: 25.11.2015 | Doc-Nr: PUB / 5145343 / 000 / 02

PD 5

en Original operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . 1

fr Moded'emploioriginal ............................... 12

es Manual de instrucciones original . . . . . . . . . . . . . . . . . . . . . . . 24

Printed: 25.11.2015 | Doc-Nr: PUB / 5145343 / 000 / 02

1 Information about the documentation

1.1 Explanation of signs used

1.1.1 Warning signs

The following warning signs are used:

DANGER! Draws attention to imminent danger that will lead to seri-

ous personal injury or fatality.

WARNING! Draws attention to a potentially dangerous situation that

could lead to serious personal injury or fatality.

CAUTION! Draws attention to a potentially dangerous situation that

could lead to slight personal injury or damage to the equipment or

other property.

1.1.2 Symbols

The following symbols are used:

Read the operating instructions before use.

On/off button

“Measure” button

KCCREM-HLTPD5

1.1.3 Illustrations

The illustrations in these operating instructions are intended to promote a

better understanding and may deviate from the actual version of the product.

These numbers refer to the corresponding illustrations found at the

beginning of these operating instructions.

The numbering in the illustrations reflects the order of the work steps

in the illustration and may deviate from the numbering of work steps

in the text.

Item reference numbers are used in the overview illustration. In the

product overview section, the numbers shown in the legend relate to

these item reference numbers.

1.2 About this documentation

▶Read these operating instructions before the product is used or operated

for the first time. This is a is a prerequisite for safe, trouble-free handling

and use of the product.

▶Observe the safety instructions and warnings printed in this documenta-

tion and on the tool.

Printed: 25.11.2015 | Doc-Nr: PUB / 5145343 / 000 / 02

▶Always keep the operating instructions with the tool and make sure that

the operating instructions are with the tool when it is given to other

persons.

We reserve the right to make changes. Errors excepted.

1.3 Product information

Hilti products are designed for professional use and may be operated, ser-

viced and maintained only by trained, authorized personnel. This personnel

must be informed of any particular hazards that may be encountered. The

product and its ancillary equipment may present hazards when used incor-

rectly by untrained personnel or when used not as directed.

The type designation and serial number are printed on the type identification

plate.

▶Write down the serial number in the table below. You will be required to

state the product details when contacting Hilti Service or your local Hilti

organization to enquire about the product.

Product information

Laser range meter PD 5

Generation 01

Serial no.

1.4 Laser information on the product

Laser information

Laser Class 2 based on the IEC60825-1 / EN60825-

1:2007 standard in compliance with CFR 21 § 1040

(Laser Notice 50).

Laser Class 2: Do not stare into the beam. Do not di-

rect the beam toward other persons or toward areas in

which other persons, who are not involved in the work

with lasers, may be present.

This product may be used without need for further

protective measures. The eyelid closure reflex protects

the eyes when a person looks into the beam uninten-

tionally for a brief moment. This eyelid closure reflex,

however, may be negatively affected by medicines,

alcohol or drugs. Nevertheless, as with the sun, one

should not look directly into sources of bright light. Do

not direct the laser beam toward persons.

Printed: 25.11.2015 | Doc-Nr: PUB / 5145343 / 000 / 02

2 Safety

2.1 Safety instructions

2.1.1 Basic information concerning safety

In addition to the safety rules listed in the individual sections of these

operating instructions, the following rules must be strictly observed at

all times. The product and its ancillary equipment may present hazards

when used incorrectly by untrained personnel or when used not as directed.

▶Keep all safety instructions and information for future reference.

▶Stay alert, watch what you are doing and use common sense when

working with the product. Do not use the product while you are tired

or under the influence of drugs, alcohol or medication. A moment of

inattention while operating the product may result in serious personal

injury.

▶Do not render safety devices ineffective and do not remove information

and warning notices.

▶If the product is opened improperly, laser radiation in excess of Class 2

may be emitted. Have the product repaired only by Hilti Service.

▶Tampering with or modification of the product is not permitted.

▶Check that the product functions correctly each time before use.

▶Measurements taken through panes of glass or other objects may be

inaccurate.

▶The measurement may be incorrect if the conditions under which the

measurement is taken change rapidly, e.g. due to people walking through

the path of the laser beam.

▶Do not point the product toward the sun or other powerful light sources.

▶Take the influences of the surrounding area into account. Do not use the

tool where there is a risk of fire or explosion.

▶Observe the information printed in the operating instructions concerning

operation, care and maintenance.

2.1.2 General safety rules

▶Check the product for damage before use. Have the damage repaired by

Hilti Service.

▶Check the accuracy of the product after it has been dropped or subjected

to other mechanical stresses.

▶Although the product is designed for the tough conditions of jobsite use,

as with other measuring instruments it should be treated with care.

▶Products which are not in use must be stored in a dry, high place or

locked away out of reach of children.

▶The product is not intended for use by children.

▶Observe the national health and safety requirements.

Printed: 25.11.2015 | Doc-Nr: PUB / 5145343 / 000 / 02

2.1.3 Proper preparation of the working area

▶Avoid unfavorable body positions when working from ladders. Make sure

you have a safe stance and that you stay in balance at all times.

▶Secure the site at which you are taking measurements and take care to

avoid directing the laser beam toward other persons or toward yourself.

▶When the product is brought into a warm environment from very cold

conditions, or vice-versa, allow it to become acclimatized before use.

▶Use the product only within its specified limits.

▶Keep the laser exit window clean in order to avoid measurement errors.

▶Observe the accident prevention regulations applicable in your country.

2.1.4 Laser classification

Depending on the version, the laser range meter complies with Laser Class

2 in accordance with IEC 60825-1:2007 /EN 60825-1:2007 and Class II in

accordance with CFR 21 § 1040 (FDA). This tool may be used without need

for further protective measures. The eyelid closure reflex protects the eyes

when a person looks into the beam unintentionally for a brief moment. This

eyelid closure reflex, however, may be negatively affected by medicines,

alcohol or drugs. Nevertheless, as with the sun, one should never look

directly into powerful sources of bright light. Do not direct the laser beam

toward persons.

2.1.5 Electromagnetic compatibility

Although the device complies with the strict requirements of the applicable

directives, Hilti cannot entirely rule out the possibility of interference to the

device caused by powerful electromagnetic radiation, possibly leading to

incorrect operation. Check the accuracy of the device by taking measure-

ments by other means when working under such conditions or if you are

unsure. Likewise, Hilti cannot rule out the possibility of interference with

other devices (e.g. aircraft navigation equipment). The tool complies with

the requirements of class A; The possibility of interference occurring in a

domestic environment cannot be excluded.

Only for Korea: This laser range meter is suitable for commercial and

industrial use and for the electromagnetic radiation encountered in this field

(Class A). Users must pay attention to this point and make sure that this

laser range meter is not used in occupied living areas.

3 Description

3.1 Overview of the product 1

@Laser emitting and receiving

lens

;Display

=“Measure” button

%On/off button

&Battery compartment cover

(Batteries

Printed: 25.11.2015 | Doc-Nr: PUB / 5145343 / 000 / 02

3.2 Intended use

The product described is a laser range meter. It is designed for taking indi-

vidual measurements as well as the continuous measurement of distances.

Distances can be measured from all stationary targets without a highly

reflective surface, i.e. concrete, stone, wood, plastic, paper, etc. The use of

prisms or other highly reflective targets is not permissible and, if attempted,

may falsify the results.

The product is approved for use with batteries of the type AAA.

3.3 Explanation of the display

Display

1. Battery charge state

2. Last distance measured before the current measure-

ment

3. Current distance from continuous distance measure-

ment or, respectively, the last measured distance.

4. Error message

3.4 Items supplied

Laser range meter, 2 batteries, operating instructions, manufacturer’s cer-

tificate

Note

To help ensure safe and reliable operation, use only genuine Hilti spare

parts and consumables. Spare parts, consumables and accessories

approved by Hilti for use with the product can be found at your local

Hilti Center or online at: www.hilti.com

4 Technical data

PD 5

Power source 1.5 V

Measuring range with target plate 0.25 m … 100 m

(0 ft - 9.8 in … 328 ft)

Distance measurement accuracy ±1.5 mm + 20 ppm

(±0.06 in + 20 ppm)

Calibration measuring area 1 m … 5 m

(3 ft … 16 ft)

Protection class in accordance

with IEC 60529

IP55

Operating temperature −10 ℃ … 50 ℃

(14 ℉ … 122 ℉)

Printed: 25.11.2015 | Doc-Nr: PUB / 5145343 / 000 / 02

PD 5

Recommended temperature

range for transport and storage

−30 ℃ … 70 ℃

(−22 ℉ … 158 ℉)

Weight 100 g

(3.5 oz)

5 Operation

5.1 Inserting the batteries 2

Note

Take care to ensure correct battery polarity. Change the batteries only

in pairs. Do not use damaged batteries.

▶Open the battery compartment and insert the batteries.

5.2 Fitting and removing the clip 3

1. Slide the clip on from the rear until it snaps into place.

2. Remove the clip by lifting it upwards.

5.3 Switching the laser range meter on and off

1. Press the or button.

◁The and buttons switch the laser range meter on.

◁The button activates the laser.

2. When switched on, press the button.

◁The laser range meter will be switched off.

Note

The laser switches itself off automatically after 1 minute.

The laser range meter switches itself off automatically after 10

minutes.

5.4 Switching the signal tone on/off

1. To activate the “Settings” menu, press and hold the button for 2

seconds.

2. To switch the signal tone on or off, press the button briefly.

3. After selecting the desired signal tone status, press the button for 2

seconds.

◁All settings will be saved.

◁The laser range meter will be switched off.

5.5 Setting the unit of measure

1. To activate the “Settings” menu, press and hold the button for 2

seconds.

2. Press the button briefly to display the unit of measure settings function.

Printed: 25.11.2015 | Doc-Nr: PUB / 5145343 / 000 / 02

Otros manuales para PD 5

Tabla de contenidos

Otros manuales de Instrumento de medición de Hilti

Hilti

Hilti PMC 46 Manual de usuario

Hilti

Hilti PS 300 Manual de usuario

Hilti

Hilti PD 38 Manual de usuario

Hilti

Hilti PR30-HVSG-A12 Manual de usuario

Hilti

Hilti PX 10 Manual de usuario

Hilti

Hilti PR 3-HVSG Manual de usuario

Hilti

Hilti PR 30-HVS A12 Manual de usuario

Hilti

Hilti PD 38 Manual de usuario

Hilti

Hilti PD-I Manual de usuario

Hilti

Hilti PM 2-L Manual de usuario

Hilti

Hilti PD 42 Manual de usuario

Hilti

Hilti PRA 38 Manual de usuario

Hilti

Hilti PD 32 Manual de usuario

Hilti

Hilti PD-I Manual de usuario

Hilti

Hilti PD 30 Manual de usuario

Hilti

Hilti PR 30-HVS A12 Manual de usuario

Hilti

Hilti pd-e Manual de usuario

Hilti

Hilti PD-I Manual de usuario

Hilti

Hilti PD 40 Manual de usuario

Hilti

Hilti NURON VC 10L-22 Manual de usuario

Hilti

Hilti pd-e Manual de usuario

Hilti

Hilti PRI 36 Manual de usuario

Hilti

Hilti PD-I Manual de usuario

Hilti

Hilti pd-e Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario