HIK VISION DS-K1T802 Manual de usuario
Access Control Terminal
Quick Start Guide
Access Control Terminal·Quick Start Guide
i
Quick Start Guide
©2018 Hangzhou Hikvision Digital Technology Co., Ltd.
This quick start guide is applied for access control terminal.
Product Serials
Model
Product Name
DS-K1T802
DS-K1T802E
Access Control Terminal
(EM Card)
DS-K1T802M
Access Control Terminal
(Mifare Card)
It includes instructions on how to use the Product. The software
embodied in the Product is governed by the user license
agreement covering that Product.
About this Manual
This Manual is subject to domestic and international copyright
protection. Hangzhou Hikvision Digital Technology Co., Ltd.
(“Hikvision”) reserves all rights to this manual. This manual cannot
be reproduced, changed, translated, or distributed, partially or
wholly, by any means, without the prior written permission of
Hikvision.
Trademarks
and other Hikvision marks are the property of
Hikvision and are registered trademarks or the subject of
applications for the same by Hikvision and/or its affiliates. Other
trademarks mentioned in this manual are the properties of their
respective owners. No right of license is given to use such
trademarks without express permission.
Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW,
HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED,
Access Control Terminal·Quick Start Guide
ii
INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
REGARDING THIS MANUAL. HIKVISION DOES NOT WARRANT,
GUARANTEE, OR MAKE ANY REPRESENTATIONS REGARDING THE
USE OF THE MANUAL, OR THE CORRECTNESS, ACCURACY, OR
RELIABILITY OF INFORMATION CONTAINED HEREIN. YOUR USE OF
THIS MANUAL AND ANY RELIANCE ON THIS MANUAL SHALL BE
WHOLLY AT YOUR OWN RISK AND RESPONSIBILITY.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN
NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES,
OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL,
CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES,
INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS
PROFITS, BUSINESS INTERRUPTION, SECURITY BREACHES, OR LOSS
OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE
OF OR RELIANCE ON THIS MANUAL, EVEN IF HIKVISION HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF LIABILITY OR CERTAIN DAMAGES, SO SOME OR ALL
OF THE ABOVE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO
YOU.
Support
Should you have any questions, please do not hesitate to contact
your local dealer.
0200001080228
Access Control Terminal·Quick Start Guide
iii
Regulatory Information
FCC Information
Please take attention that changes or modification not expressly
approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
FCC compliance: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for
help.
This equipment should be installed and operated with a minimum
distance 20cm between the radiator and your body.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied
accessories too are marked with "CE" and comply
Access Control Terminal·Quick Start Guide
iv
therefore with the applicable harmonized European standards
listed under the EMC Directive 2014/30/EU, the RoHS Directive
2011/65/EU.
2012/19/EU (WEEE directive): Products marked with
this symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper
recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or
dispose of it at designated collection points. For more information
see: www.recyclethis.info.
2006/66/EC (battery directive): This product contains
a battery that cannot be disposed of as unsorted
municipal waste in the European Union. See the
product documentation for specific battery
information. The battery is marked with this symbol,
which may include lettering to indicate cadmium (Cd), lead (Pb),
or mercury (Hg). For proper recycling, return the battery to your
supplier or to a designated collection point. For more information
see: www.recyclethis.info.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards
requirements.
Safety Instruction
These instructions are intended to ensure that user can use the
product correctly to avoid danger or property loss.
The precaution measure is divided into Warnings and Cautions:
Warnings: Neglecting any of the warnings may cause serious
injury or death.
Cautions: Neglecting any of the cautions may cause injury or
equipment damage.
Access Control Terminal·Quick Start Guide
v
Warnings
All the electronic operation should be strictly compliance with
the electrical safety regulations, fire prevention regulations and
other related regulations in your local region.
Please use the power adapter, which is provided by normal
company. The power consumption cannot be less than the
required value.
Do not connect several devices to one power adapter as
adapter overload may cause over-heat or fire hazard.
Please make sure that the power has been disconnected before
you wire, install or dismantle the device.
When the product is installed on wall or ceiling, the device shall
be firmly fixed.
If smoke, odors or noise rise from the device, turn off the
power at once and unplug the power cable, and then please
contact the service center.
If the product does not work properly, please contact your
dealer or the nearest service center. Never attempt to
disassemble the device yourself. (We shall not assume any
responsibility for problems caused by unauthorized repair or
maintenance.)
Cautions
Do not drop the device or subject it to physical shock, and do
not expose it to high electromagnetism radiation. Avoid the
Warnings Follow these
safeguards to prevent
serious injury or death.
Cautions Follow these
precautions to prevent
potential injury or
material damage.
Access Control Terminal·Quick Start Guide
vi
equipment installation on vibrations surface or places subject to
shock (ignorance can cause equipment damage).
Do not place the device in extremely hot (refer to the
specification of the device for the detailed operating
temperature), cold, dusty or damp locations, and do not expose
it to high electromagnetic radiation. The appropriate operation
temperature is 0℃ to +45℃, and the storage temperature
should be -10℃ to +55℃.
The device cover for indoor use shall be kept from rain and
moisture.
Exposing the equipment to direct sun light, low ventilation or
heat source such as heater or radiator is forbidden (ignorance
can cause fire danger).
Do not aim the device at the sun or extra bright places. A
blooming or smear may occur otherwise (which is not a
malfunction however), and affecting the endurance of sensor at
the same time.
Please use the provided glove when open up the device cover,
avoid direct contact with the device cover, because the acidic
sweat of the fingers may erode the surface coating of the device
cover.
Please use a soft and dry cloth when clean inside and outside
surfaces of the device cover, do not use alkaline detergents.
Please keep all wrappers after unpack them for future use. In
case of any failure occurred, you need to return the device to
the factory with the original wrapper. Transportation without
the original wrapper may result in damage on the device and
lead to additional costs.
Improper use or replacement of the battery may result in
hazard of explosion. Replace with the same or equivalent type
only. Dispose of used batteries according to the instructions
provided by the battery manufacturer.
Access Control Terminal·Quick Start Guide
vii
Table of Contents
1 Overview............................................................................... 1
1.1 Introduction ........................................................................... 1
1.2 Main Features ........................................................................ 1
2 Appearance ........................................................................... 3
2.1 Appearance of the Termianl................................................... 3
2.2 Description of Keypad Items .................................................. 4
3 Terminal Connection.............................................................. 4
3.1 Terminal Description .............................................................. 4
3.2 External Device Wiring........................................................... 5
4 Installation ............................................................................ 7
4.1 Mounting with Gang Box ....................................................... 7
4.2 Mounting without Gang Box .................................................. 8
5 Activating the Access Control Terminal..................................10
5.1 Activating via SADP Software ............................................... 10
5.2 Activating via Client Software .............................................. 12
Access Control Terminal·Quick Start Guide
1
1Overview
1.1 Introduction
DS-K1T802 Series Standalone Access Control
Terminal
DS-K1T802 is a series of standalone access control terminal
designed with a LCD display screen. It supports TCP/IP
network communication, offline records storage functions
and so on.
1.2 Main Features
Equipped with 32-bit high-speed processor
Supports TCP/IP network communication, with self-adaptive
network interface. The communication data is specially
encrypted to relieve the concern of privacy leak
Supports EM card and Mifare card reading
Supports authentication methods of card, card and password,
card or password
Doorbell ring design
Access Control Terminal·Quick Start Guide
2
Supports time synchronization via NTP, manual or automatic
method
Supports online upgrade, remote control of the doors, first
card open function, first card authentication function, super
card, super password function and device rebooting control
The access controller can store 3 thousand legal cards and 10
thousand card swiping records
Supports event card linkage
Supports M1 card encryption function
Supports IP address conflict detection
Supports up to 500 groups of authentication password
Unlocking overtime alarm, invalid card swiping over times
alarm, blocklist alarm, and duress card/code alarm
Supports various card types as normal/extended open
duration/ blocklist/ patrol/ guest/ duress/ super card, etc.
Supports multiple events uploading methods: channel, and
listening; The device can upload one integrated event and
four real-time events via channel uploading method
Supports getting device events via SDK
Data can be permanently saved after power-off
Accurate data and time display provided by built-in electronic
clock and watchdog program to ensure the basic function of
the terminal
Remotely device rebooting control
Supports alarm of offline event exceeding 90%
Otros manuales para DS-K1T802
1
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Terminal táctil de HIK VISION
HIK VISION
HIK VISION DS-K5032-D Manual de usuario
HIK VISION
HIK VISION C2000IC12.0-24P-DE Manual de usuario
HIK VISION
HIK VISION UD19294B Manual de usuario
HIK VISION
HIK VISION DS-K1T502 Series Instrucciones de funcionamiento
HIK VISION
HIK VISION DS-K1T502 Series Manual de usuario
HIK VISION
HIK VISION DS-K11T341BMI-T Manual de usuario
HIK VISION
HIK VISION DS-K5671-3XF/ZU Manual de usuario
HIK VISION
HIK VISION DS-K1T341BMWI-T Manual de usuario
HIK VISION
HIK VISION DS-K5032 Series Manual de usuario
HIK VISION
HIK VISION DS-K5604A-3XF Series Manual de usuario
HIK VISION
HIK VISION DS-K1T642 Series Manual de usuario
HIK VISION
HIK VISION DS-K1A8503 Manual de usuario
HIK VISION
HIK VISION DS-K1A801MF Manual de usuario
HIK VISION
HIK VISION DS-K1T8003 Series Manual de usuario
HIK VISION
HIK VISION DS-K1T321 Series Manual de usuario
HIK VISION
HIK VISION DS-K5604A-3XF/V Manual de usuario
HIK VISION
HIK VISION DS-K1T607 Series Manual de usuario
HIK VISION
HIK VISION DS-K1T341C Series Manual de usuario
HIK VISION
HIK VISION K1T671 Manual de usuario
HIK VISION
HIK VISION DS-K5604A-3XF Series Manual de usuario
