HIK VISION TurboHD H0T Series Manual de usuario
UM DS-2CEx6H0T-xIT3ZF 042318NA 1
• DS-2CE16H0T-AIT3ZF
• DS-2CEAH0T-IT3ZF
TurboHD
H0T Series
Bullet and Turret Camera
User Manual
Thank you or purchasing our product. I there are
any questions or requests, do not hesitate to contact
the dealer.
This manual applies to the models below:
Type
Model
Type I
Camera
DS
-
2CE16H0T
-
A
IT3ZF
Type
II
Camera
DS
-
2CE56H0T
-
IT3Z
F
Hikvision USA Inc., 18639 Railroad St., City o Industry,
CA 91748, USA • Hikvision Canada, 4848 rue Levy,
Saint Laurent, Quebec, Canada, H4R 2P1
Telephone: +1-909-895-0400 • Toll Free in USA:
+1-866-200-6690 • E-Mail: [email protected] •
www.hikvision.com
COPYRIGHT ©2017-2018 Hangzhou Hikvision Digital
Technology Co., Ltd. ALL RIGHTS RESERVED.
Any and all in ormation, including, among others,
wordings, pictures, graphs are the properties o
Hangzhou Hikvision Digital Technology Co., Ltd. or its
subsidiaries (hereina ter re erred to be “Hikvision”).
This user manual (hereina ter re erred to be “the
Manual”) cannot be reproduced, changed, translated,
or distributed, partially or wholly, by any means,
without the prior written permission o Hikvision.
Unless otherwise stipulated, Hikvision does not make
any warranties, guarantees or representations,
express or implied, regarding to the Manual.
This manual may contain technical or printing errors,
and the content is subject to change without notice.
Updates will be added to new versions o this manual.
We will readily improve or update the products or
procedures described in the manual.
UM DS-2CEx6H0T-xIT3ZF 042318NA 2
Preface
. Regulatory Information
. . FCC Information
Please take attention that changes or modi ication
not expressly approved by the party responsible or
compliance could void the user’s authority to
operate the equipment.
FCC Compliance: This equipment has been tested
and ound to comply with the limits or a Class A
digital device, pursuant to part 15 o the FCC Rules.
These limits are designed to provide reasonable
protection against harm ul inter erence when the
equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate
radio requency energy and, i not installed and used
in accordance with the instruction manual, may
cause harm ul inter erence to radio communications.
Operation o this equipment in a residential area is
likely to cause harm ul inter erence, in which case
the user will be required to correct the inter erence
at his own expense.
. .2 FCC Conditions
This device complies with part 15 o the FCC Rules.
Operation is subject to the ollowing two conditions:
1. This device may not cause harm ul inter erence.
2. This device must accept any inter erence received,
including inter erence that may cause undesired
operation.
. .3 EU Conformity Statement
This product and, i applicable, the supplied
accessories too are marked with “CE” and
comply there ore with the applicable
harmonized European standards listed under
the Low Voltage Directive 2014/35/EU, the
EMC Directive 2014/30/EU.
2012/19/EU (WEEE Directive): Products
marked with this symbol cannot be
disposed o as unsorted municipal waste in
the European Union. For proper recycling,
return this product to your local supplier
upon the purchase o equivalent new
equipment, or dispose o it at designated
collection points. For more in ormation see:
www.recyclethis.in o.
2006/66/EC (Battery Directive): This
product contains a battery that cannot be
disposed o as unsorted municipal waste in
the European Union. See the product
documentation or speci ic battery
in ormation. The battery is marked with
this symbol, which may include lettering to
indicate cadmium (Cd), lead (Pb), or
mercury (Hg). For proper recycling, return
the battery to your supplier or to a
designated collection point. For more
in ormation see: www.recyclethis.in o.
UM DS-2CEx6H0T-xIT3ZF 042318NA 3
. .4 Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A)
standards requirements.
. .5 Safety Instruction
These instructions are intended to ensure that the
user can use the product correctly to avoid danger or
property loss.
The precaution measure is divided into “Warnings”
and “Cautions.”
Warnings: Serious injury or death may occur i any o
the warnings are neglected.
Cautions: Injury or equipment damage may occur i
any o the cautions are neglected.
Warnings
Follow these
sa eguards to prevent
serious injury or death.
Ca
utions
Follow these
precautions to prevent
potential injury or
material damage.
. .6
Warnings
•
In the use o the device, you must be in strict
compliance with the electrical sa ety regulations o
the nation and region.
•
Input voltage should meet both the SELV (Sa ety
Extra Low Voltage) and the Limited Power Source
with 12 VDC according to the IEC60950-1 standard.
Re er to technical speci ications or detailed
in ormation.
•
The camera is powered by an external DC power
supply (12 VDC, 1 A) that complies with the LPS,
and the output current o this external DC power
supply must be no more than 6 A.
•
Do not connect multiple devices to one power
adapter to avoid over-heating or a ire hazard
caused by overload.
•
Make sure that the plug is irmly connected to the
power socket.
•
Make sure that the device is irmly ixed i wall
mounting or ceiling mounting is adopted.
•
I smoke, odor, or noise rise rom the device, turn
o the power at once and unplug the power cord,
and then contact the service center.
•
Never attempt to disassemble the camera by
unpro essional personal.
. .7
Cautions
•
Do not drop the camera or subject it to physical
shock.
•
Do not touch senor modules with ingers.
UM DS-2CEx6H0T-xIT3ZF 042318NA 4
•
Do not place the camera in extremely hot, cold (the
operating temperature shall be -40° to 60° C),
dusty or damp locations, and do not expose it to
high electromagnetic radiation.
•
I cleaning is necessary, use a clean cloth with a bit
o ethanol, and wipe it gently.
•
Do not aim the camera at the sun or extra bright
places.
•
The sensor may be burned out by a laser beam, so
when any laser equipment is in using, make sure
that the sensor sur ace will not be exposed to the
laser beam.
•
Do not expose the device to high electromagnetic
radiation or extremely hot, cold, dusty, or damp
environments.
•
To avoid heat accumulation, good ventilation is
required or the operating environment.
•
Keep the camera away rom liquid while in use or
non-waterproo devices.
•
While in delivery, the camera shall be packed in its
original packing, or packing o the same material.
. .8 Mark Description
Table 0-1 Mark Description
Mark
Description
DC Voltage
AC Voltage
2Introduction
2. Product Features
The main eatures are as ollows:
•
High per ormance CMOS sensor
•
IR cut ilter with auto switch
•
OSD menu with con igurable parameters
•
Auto white balance
•
Internal synchronization
•
SMART IR mode
•
3-axis adjustment
2.2 Overview
2.2. Overview of Type I Camera
Figure 1 Overview o Type I Camera
UM DS-2CEx6H0T-xIT3ZF 042318NA 5
Note:
To switch the video output, press and hold the switch
button until the image turns black, then release.
Cycle through available types to return to the de ault
HD-TVI output. Four kinds o video outputs are
available: TVI, AHD, CVI, and CVBS.
2.2.2 Overview of Type II Camera
Figure 2 Overview o Type II Camera
Note:
To switch the video output, press and hold the switch
button until the image turns black, then release.
Cycle through available types to return to the de ault
HD-TVI output. Four kinds o video outputs are
available: TVI, AHD, CVI, and CVBS.
3Installation
Before you start:
•
Make sure that the device in the package is in good
condition and all the assembly parts are included.
•
Make sure that all the related equipment is
power-o during the installation.
•
Check the speci ication o the products or the
installation environment.
•
Check whether the power supply is matched with
your power output to avoid the damage.
•
Make sure the wall is strong enough to withstand
three times the weight o the camera and the
mount.
•
I the wall is cement, insert expansion bolts be ore
installing the camera. I the wall is wooden, use
sel -tapping screws to secure the camera.
•
I the product does not unction properly, contact
your dealer or the nearest service center. Do NOT
disassemble the camera or repair or maintenance
by yoursel .
3. Installation of Type I Camera
3. . Ceiling Mounting without Junction Box
Before you start:
Both wall mounting and ceiling mounting are suitable
or the bullet camera. Ceiling mounting will be taken
as an example in this section. And you can take steps
o ceiling mounting as a re erence or wall mounting.
UM DS-2CEx6H0T-xIT3ZF 042318NA 6
Steps:
1. Paste the drill template (supplied) to the place
where you want to install the camera.
2. Drill the screw holes and the cable hole (optional)
in the ceiling according to the drill template.
Figure 3 Drill Template
Note:
Drill the cable hole when using ceiling outlet to route
the cable.
3. Route the cables through the cable hole, or the
side opening.
4. Fix the camera to the ceiling with supplied screws.
Figure 4 Fix the Camera to the Ceiling
Note:
The supplied screw package contains sel -tapping
screws, and expansion bolts.
For a cement wall, expansion bolts are required to ix
the camera. For a wooden wall, sel -tapping screws
are required.
5. Connect the corresponding power cord and video
cable.
6. Power on the camera to check whether the image
on the monitor is at an optimum angle. I not,
adjust the surveillance angle.
Figure 5 3-axis Adjustment
UM DS-2CEx6H0T-xIT3ZF 042318NA 7
1) Loosen the No.
①
adjusting screw to adjust
the pan position [0° to 360°]. Tighten the No.
①
adjusting screw.
2) Loosen the No.
②
adjusting screw to adjust
the tilting position [0° to 90°]. Tighten the No.
②
adjusting screw.
3) Loosen the No.
③
adjusting screw to adjust
the rotation position [0° to 360°]. Tighten the
No.
③
adjusting screw.
3. .2 Ceiling Mounting with Junction Box
Before you start:
•
You need to purchase a junction box separately.
•
Both wall mounting and ceiling mounting are
suitable or the bullet camera. Ceiling mounting
will be taken as an example in this section. Use
ceiling mounting as a re erence or wall mounting.
Steps:
1. Paste junction box’s drill template on the ceiling.
2. Drill screw holes and the cable hole (optional) in
the ceiling according to the holes o the drill
template.
Note:
Drill the cable hole when using ceiling outlet to route
the cable.
3. Take apart the junction box and align the screw
holes o the bullet camera with those on the
junction box’s cover.
4. Fix the camera on the junction box’s cover.
Figure 6 Fix the Camera with the Gang Box
5. Attach the junction box’s body to the ceiling by
aligning the screw holes o the junction box.
6. Secure the junction box’s body with supplied
screws on the ceiling.
UM DS-2CEx6H0T-xIT3ZF 042318NA 8
Figure 7 Fix the Camera to the Ceiling
7. Route the cables through the cable hole or the
side opening o the junction box.
8. Combine the junction box cover with its body.
Figure 8 Fix the Junction Box Cover Back to its Body
9. Re er to step 6 o 2.1.1 Ceiling Mounting without
Junction Box to complete the installation.
3.2 Installation of Type II Camera
3.2. Ceiling Mounting without Junction Box
Before you start:
Both wall mounting and ceiling mounting are suitable
or the Turret camera. Ceiling mounting will be taken
as an example in this section. And you can take steps
o ceiling mounting as a re erence or wall mounting.
Steps:
1. Paste the drill template to the place where you
want to install the camera.
2. Drill the screw holes according to the drill template
and the cable hole (optional) in the ceiling.
Figure 9 Drill Template
Note:
Drill the cable hole, when adopting the ceiling outlet
to route the cable.
3. Loosen screws to remove the clip plate, and take
out the main body.
UM DS-2CEx6H0T-xIT3ZF 042318NA 9
Figure 10 Remove the Clip Plate
4. Fix the mounting base to the ceiling with supplied
screws.
Figure 11 Fix the Mounting Base on the Ceiling
Note:
The supplied screw package contains sel -tapping
screws and expansion bolts.
For a cement wall, expansion bolts are required to ix
the camera. For a wooden wall, sel -tapping screws
are required.
5. Route the cables through the cable hole or the
side opening.
6. Install the main body to the mounting base and
insert the clip plate.
Figure 12 Install the Turret Camera
7. Tighten the screws with the screwdriver.
8. Connect the corresponding cables such as power
cord and video cable.
9. Power on the camera to check whether the image
on the monitor is at an optimum angle. I not,
adjust the camera according to the igure below
to get an optimum angle.
UM DS-2CEx6H0T-xIT3ZF 042318NA 10
Figure 13 3-axis Adjustment
1). Hold camera body and rotate enclosure to
adjust the pan position [0° to 360°].
2). Move the camera body up and down to adjust
the tilt position [0° to 75°].
3). Rotate the camera body to adjust the rotation
position [0° to 360°].
3.2.2 Ceiling Mounting with Junction Box
Before you start:
•You need to purchase a junction box separately.
•Both wall mounting and ceiling mounting are
suitable or the turret camera. Ceiling mounting
will be used as an example in this section. Use
ceiling mounting as a re erence or wall mounting.
Steps:
1. Paste junction box drill template on the ceiling.
2. Drill screw holes and the cable hole (optional) in
the ceiling according to holes in the drill template.
Figure 14 Drill Template o the Junction Box
Note:
Drill the cable hole when using the ceiling outlet to
route the cable.
3. Re er to step 3 o Ceiling Mounting without
Junction Box to take out the camera’s main body.
4. Take apart the junction box, and align the camera
screw holes with those on the junction box cover.
5. Fix the camera’s mounting base on the junction
box’s cover with three PM4 × 10 screws.
Otros manuales para TurboHD H0T Series
4
Este manual sirve para los siguientes modelos
2
Otros manuales de Cámara de seguridad de HIK VISION
HIK VISION
HIK VISION EPI-4215-DE3 Manual de usuario
HIK VISION
HIK VISION TURBO HD DF7T Series Manual de usuario
HIK VISION
HIK VISION DS-2CD4312F-I Guía del usuario
HIK VISION
HIK VISION DS-2CC51A7P-VF Manual de usuario
HIK VISION
HIK VISION DS-2CD2783G1-IZS Manual de usuario
HIK VISION
HIK VISION DS-2CC5181P-VP Manual de usuario
HIK VISION
HIK VISION HiWatch Series Guía de instalación y uso
HIK VISION
HIK VISION DS-2CD2646G2T-IZS Manual de usuario
HIK VISION
HIK VISION E-series Manual de usuario
HIK VISION
HIK VISION DS-2CD4A26FWD-IZSP Manual de usuario
HIK VISION
HIK VISION UD.6L0201A1681A02 Manual de usuario
HIK VISION
HIK VISION D0T POC C Series Manual de usuario
HIK VISION
HIK VISION V5.1.0 Manual de usuario
HIK VISION
HIK VISION DS-2CD1023G0E-IF Manual de usuario
HIK VISION
HIK VISION PanoVu Series Manual de usuario
HIK VISION
HIK VISION DS-2CE16D(F)7T-IT3Z Manual de usuario
HIK VISION
HIK VISION DS-2CD2345G0P-I Manual de usuario
HIK VISION
HIK VISION DS2CC52C7TVPIR Manual de usuario
HIK VISION
HIK VISION UD05108B Manual de usuario
HIK VISION
HIK VISION DS-2DB4236I-CWX Manual de usuario
