HIK VISION DS-2CE16D0T-IR/IRP Manual de usuario
TURBO HD
TVI Bullet & Turret Camera
User Manual
User Manual
Thank you for purchasing our product. If there are any
questions, or requests, do not hesitate to contact the
dealer.
This manual applies to the model listed below.
Type
Model
Type I
DS-2CE16D0T-IR/IRP
Type II
DS-2CE56D0T-IRM
Type III
DS-2CE56D0T-IRP
This manual may contain several technically incorrect
places or printing errors, and the content is subject to
change without notice. The updates will be added to
the new version of this manual. We will readily improve
or update the products or procedures described in the
manual.
0200001080423
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and
found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection
against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in
which case the user will be required to correct the
interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause undesired
operation
EU Conformity Statement
This product and - if applicable - the
supplied accessories too are marked with
"CE" and comply therefore with the
applicable harmonized European
standards listed under the EMC Directive 2014/30/EU,
the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products
marked with this symbol cannot be
disposed of as unsorted municipal waste in
the European Union. For proper recycling,
return this product to your local supplier
upon the purchase of equivalent new
equipment, or dispose of it at designated collection
points. For more information see: www.recyclethis.info.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A)
standards requirements.
Warning
This is a class A product. In a domestic environment this
product may cause radio interference in which case the
user may be required to take adequate measures.
Safety Instruction
These instructions are intended to ensure that user can
use the product correctly to avoid danger or property
loss.
The precaution measure is divided into “Warnings” and
“Cautions”
Warnings: Serious injury or death may occur if any of
the warnings are neglected.
Cautions: Injury or equipment damage may occur if any
of the cautions are neglected.
Warnings
In the use of the product, you must be in strict
compliance with the electrical safety regulations of
the nation and region.
Refer to technical specifications for detailed
information.
Input voltage should meet both the SELV (Safety Extra
Low Voltage) and the Limited Power Source with 12 V
DC according to the IEC60950-1 standard. Refer to
technical specifications for detailed information.
Do not connect several devices to one power adapter
as adapter overload may cause over-heating or a fire
hazard.
Make sure that the plug is firmly connected to the
power socket.
When the product is mounted on wall or ceiling, the
device shall be firmly fixed.
If smoke, odor or noise rise from the device, turn off
the power at once and unplug the power cable, and
then contact the service center.
If the product does not work properly, contact your
dealer or the nearest service center. Never attempt to
disassemble the camera yourself. (We shall not
assume any responsibility for problems caused by
unauthorized repair or maintenance.)
Cautions
Make sure the power supply voltage is correct before
using the camera.
Do not drop the camera or subject it to physical
shock.
Do not touch senor modules with fingers. If cleaning
is necessary, use clean cloth with a bit of ethanol and
wipe it gently.
Do not aim the camera at the sun or extra bright
places. Blooming or smearing may occur otherwise
(which is not a malfunction), and affect the
endurance of sensor at the same time.
Warnings Follow
these safeguards to
prevent serious injury
or death.
Cautions Follow these
precautions to prevent
potential injury or
material damage.
The sensor may be burned out by a laser beam, so
when any laser equipment is in using, make sure that
the surface of sensor will not be exposed to the laser
beam.
Do not place the camera in extremely hot, cold, dusty
or damp locations, and do not expose it to high
electromagnetic radiation.
To avoid heat accumulation, good ventilation is
required for operating environment.
Keep the camera away from liquid while in use.
While in delivery, the camera shall be packed in its
original packing, or packing of the same texture.
Mark Description
Table 0-1 Mark Description
Mark
Description
DC Voltage
Introduction
Product Features
The main features are as follows:
High performance CMOS sensor
Auto white balance
Auto electronic shutter
Auto gain control (AGC)
IR cut filter
3-axis adjustment
Note:
Type III camera is applicable for indoor only.
Overview
1.2.1 Type I Camera Overview
Video Cable
Power Cord
Mounting
Base
Main Body
Lens
IR LED
Figure 1. 1 Type I Camera Overview
1.2.2 Type II Camera Overview
Mounting
Base
Trim Ring
Enclosure
Camera
Video
Cable
Power
Cord
Figure 1. 2 Type II Camera Overview
1.2.3 Type III Camera Overview
Enclosure
Trim Ring
Mounting
Base
Main Body
Video
CablePower
Cord
Figure 1. 3 Type III Camera Overview
Installation
Installation Preparation
Before you start:
Make sure that the device in the package is in good
condition and all the assembly parts are included.
Make sure that all the related equipment is power-off
during the installation.
Check the specification of the products for the
installation environment.
Check whether the power supply is matched with
your power output to avoid damage.
Make sure the wall is strong enough to withstand
three times the weight of the camera and the
mounting bracket.
If the wall is cement, you need to insert expansion
bolts before you install the camera. If the wall is
wooden, you can use self-tapping screws to secure
the camera.
If the product does not function properly, contact
your dealer or the nearest service center. Do NOT
disassemble the camera for repair or maintenance by
yourself.
Installation of Type I Camera
Steps:
1. Attach the dill template to the ceiling.
2. Drill the screw holes according to the drill template,
and the cable hole (optional) on the ceiling.
47.6
13.7 27.5
Φ68
3-Φ4
Unit：mm
Figure 2. 1 Drill Template
Note:
Cable hole is required when adopting ceiling outlet to
route the cable.
3. Attach the mounting base of the type I camera to
the ceiling and secure the camera with supplied
screws.
Figure 2. 2 Secure the camera to the ceiling
Note:
In the supplied screw package, both self-tapping
screws and expansion blots are contained.
If the wall is cement, expansion blots are required
to fix the camera. If the wall is wooden,
self-tapping screws are required.
4. Route the cables through the cable hole (optional),
or the side opening.
5. Connect the corresponding power cord and video
cable.
6. Power on the camera to check whether the image
on the monitor is gotten from the optimum angle.
If not, adjust the camera according to the figure
below to get an optimum angle.
1). Loosen the No.1 adjusting screw to adjust the
pan position (0° to 360°).
2). Tighten the No.1 adjusting screw.
3). Loosen the No.2 adjusting screw to adjust the
tilting position (0° to 180°).
4). Tighten the No. 2 adjusting screw.
5). Loosen the No.3 adjusting screw to adjust the
rotation position (0° to 360°).
6). Tighten the No.3 adjusting screw.
0°to 360°
3
2
1
0°to 360° 0°to 180°
Figure 2. 3 3-Axis Adjustment
Installation of Type II camera
Steps:
1. Use the hex wrench to loosen the screw, and
remove the mounting base from the camera body,
shown as the figure 2.4.
r
e
r
e
Figure 2. 4 Disassemble the Camera
2. Attach the drill template (supplied) to the place
where you want to install the camera, and then drill
the screw holes according to the drill template, and
the cable hole (optional) on the ceiling.
Note:
Cable hole is required when adopting ceiling outlet to
route the cable.
47.6
13.7 27.5
Φ68
3-Φ4
Unit：mm
Figure 2. 5 Drill Template
3. Attach the mounting base to the ceiling and secure
them with supplied screws
Figure 2. 6 Attach the Mounting Base to the Ceiling
Note:
In the supplied screw package, both self-tapping
screws and expansion blots are contained.
If the wall is cement, expansion blots are required
to fix the camera. If the wall is wooden,
self-tapping screws are required.
4. Route the cables through the cable hole (optional),
or the side opening.
5. Pull out the clip plate and secure the camera with
the trim ring to the mounting base.
6. Push the clip plate in and tighten the screw to
secure the camera with the mounting base.
Clip Plate
Side
Opening
Figure 2. 7 Secure the Camera with Mounting Base
7. Connect the corresponding cables, such as power
cord, and video cable.
8. Power on the camera to check whether the image
on the monitor is gotten from the optimum angle. If
not, adjust the camera according to the figure below
to get an optimum angle.
1). Hold the camera body and rotate the enclosure
to adjust the pan position [0° to 360°].
2). Move the camera body up and down to adjust
the tilt position [0° to 75°].
3). Rotate the camera body to adjust the rotation
position [0° to 360°].
Pan Positioning Range：
0°to 360°
Rotation Positioning Range：
0°to 360°
Tilt Positioning Range：
0°to 75°
Figure 2. 8 3-axis Adjustment
Installation of Type III Camera
Steps:
1. Attach the drill template (supplied) to the place
where you want to install the camera, and then drill
the screw holes and the cable hole (optional)
according to the drill template on the ceiling.
Note:
Cable hole is required when adopting ceiling outlet to
route the cable.
Φ86
Φ72
Φ40
3 - Φ4
120°
Figure 2. 9 Drill Template
2. Attach the mounting base to the ceiling and secure
them with supplied screws
Figure 2. 10 Attach the Mounting Base to the Ceiling
Note:
In the supplied screw package, both self-tapping
screws and expansion blots are contained.
If the wall is cement, expansion blots are required
to fix the camera. If the wall is wooden,
self-tapping screws are required.
3. Route the cables through the cable hole (optional),
or the side opening.
4. Align the camera with the mounting base, secure
the camera with the mounting base, and fix the trim
ring to the camera.
Figure 2. 11 Secure the Camera with Mounting Base
5. Connect the corresponding cables, such as power
cord, and video cable.
6. Power on the camera to check whether the image
on the monitor is gotten from the optimum angle. If
not, adjust the camera according to the figure below
to get an optimum angle.
1). Hold the camera body and rotate the enclosure
to adjust the pan position [0° to 360°].
2). Move the camera body up and down to adjust
the tilt position [0° to 75°].
3). Rotate the camera body to adjust the rotation
position [0° to 360°].
Pan Positioning Range：
0°to 360°
Rotation Positioning Range：
0°to 360°
Tilt Positioning Range：
0°to 75°
Figure 2. 12 3-axis Adjustment
Menu Description
Purpose:
Call the menu by clicking button on the PTZ Control
interface, or call the preset No.95.
Steps:
1. Connect the camera with the TVI DVR, and the
monitor, shown as the figure 3-1.
Camera
TVI DVR
Monitor
Figure 3. 1 Connection
2. Power on the analog camera, TVI DVR, and the
monitor to view the image on the monitor.
3. Click PTZ Control to enter the PTZ Control interface.
4. Call the camera menu by clicking button, or call
the preset No. 95.
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Cámara de seguridad de HIK VISION
HIK VISION
HIK VISION HiLook IK-4142B-MH/W Manual de usuario
HIK VISION
HIK VISION iDS-TCV907-BIR Manual de usuario
HIK VISION
HIK VISION DS-2CD7A85G0-IZHS Manual de usuario
HIK VISION
HIK VISION DS-2CC12D8T-AMM Manual de usuario
HIK VISION
HIK VISION IR Smart Speed Dome Manual de usuario
HIK VISION
HIK VISION DS-2CD2786G2T-IZS Manual de usuario
HIK VISION
HIK VISION DS-2DE7A412MCG-EB Manual de usuario
HIK VISION
HIK VISION DS-2TD4166T-9 Manual de usuario
HIK VISION
HIK VISION D0T Manual de usuario
HIK VISION
HIK VISION DS-2XM6222FWD-I Manual de usuario
HIK VISION
HIK VISION DS-2DE2C200MWG-E Manual de usuario
HIK VISION
HIK VISION Network Dome Camera Manual de usuario
HIK VISION
HIK VISION DS-2CD5A46G0-IZ/UH Manual de usuario
HIK VISION
HIK VISION DS-2XC6685G0 Manual de usuario
HIK VISION
HIK VISION DS-2DE2103 Manual de usuario
HIK VISION
HIK VISION DS-2DF6336V-AEL Manual de usuario
HIK VISION
HIK VISION DS-2CD3021G0-I Manual de usuario
HIK VISION
HIK VISION DS-2CD4A26FWD-IZSP Manual de usuario
HIK VISION
HIK VISION DS-2PT3326IZ Manual de usuario
HIK VISION
HIK VISION DS-2CE59H8T-(A)VPIT3ZF Manual de usuario
