HIK VISION 2T series Manual de usuario

Network Bullet Camera

Quick Start Guide

Network Bullet Camera·Quick Start Guide

About this Manual

This Manual is applicable to 2Txx Network Camera.

The Manual includes instructions for using and managing the

product. Pictures, charts, images and all other information

hereinafter are for description and explanation only. The

information contained in the Manual is subject to change, without

notice, due to firmware updates or other reasons. Please find the

latest version in the company website

Please use this user manual under the guidance of professionals.

Legal Disclaimer

REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF

PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. OUR COMPANY

SHALL NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL OPERATION,

PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER

ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET

SECURITY RISKS; HOWEVER, OUR COMPANY WILL PROVIDE TIMELY

TECHNICAL SUPPORT IF REQUIRED.

SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL

RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS

PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE

APPLICABLE LAW. OUR COMPANY SHALL NOT BE LIABLE IN THE

EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.

IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE

APPLICABLE LAW, THE LATER PREVAILS.

Regulatory Information

FCC Information

Network Bullet Camera·Quick Start Guide

Please take attention that changes or modification not expressly

approved by the party responsible for compliance could void the

user’s authority to operate the equipment.

FCC compliance: This equipment has been tested and found to

comply with the limits for a Class B digital device, pursuant to part

15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

FCC Conditions

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including

interference that may cause undesired operation.

Network Bullet Camera·Quick Start Guide

EU Conformity Statement

This product and - if applicable - the supplied

accessories too are marked with "CE" and comply

therefore with the applicable harmonized European

standards listed under the EMC Directive 2014/30/EU, the RoHS

Directive 2011/65/EU

2012/19/EU (WEEE directive): Products marked

with this symbol cannot be disposed of as unsorted

municipal waste in the European Union. For proper

recycling, return this product to your local supplier

upon the purchase of equivalent new equipment, or dispose of it at

designated collection points. For more information see:

www.recyclethis.info

2006/66/EC (battery directive): This product

contains a battery that cannot be disposed of as

unsorted municipal waste in the European Union.

See the product documentation for specific battery

information. The battery is marked with this symbol, which may

include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg).

For proper recycling, return the battery to your supplier or to a

designated collection point. For more information see:

www.recyclethis.info

Industry Canada ICES-003 Compliance

This device meets the CAN ICES-3 (B)/NMB-3(B) standards

requirements.

Safety Instruction

Network Bullet Camera·Quick Start Guide

These instructions are intended to ensure that user can use the

product correctly to avoid danger or property loss.

The precaution measure is divided into “Warnings” and “Cautions”

Warnings: Serious injury or death may occur if any of the warnings

are neglected.

Cautions: Injury or equipment damage may occur if any of the

cautions are neglected.

Warnings

●In the use of the product, you must be in strict compliance with

the electrical safety regulations of the nation and region. Please

refer to technical specifications for detailed information.

●Input voltage should meet both the SELV (Safety Extra Low

Voltage) and the Limited Power Source with 12 VDC according

to the IEC60950-1 standard. Please refer to technical

specifications for detailed information.

●Do not connect several devices to one power adapter as

adapter overload may cause over-heating or a fire hazard.

Warnings Follow these

safeguards to prevent

serious injury or death.

Cautions Follow these

precautions to prevent potential

injury or material damage.

Network Bullet Camera·Quick Start Guide

●Please make sure that the plug is firmly connected to the power

socket. When the product is mounted on wall or ceiling, the

device shall be firmly fixed.

●If smoke, odor or noise rise from the device, turn off the power

at once and unplug the power cable, and then please contact

the service center.

●Proper configuration of all passwords and other security

settings is the responsibility of the installer and/or end-user.

Cautions

●Make sure the power supply voltage is correct before using the

camera.

●Do not drop the camera or subject it to physical shock.

●Do not touch sensor modules with fingers. If cleaning is

necessary, use clean cloth with a bit of ethanol and wipe it

gently. If the camera will not be used for an extended period,

please replace the lens cap to protect the sensor from dirt.

●Do not aim the camera at the sun or extra bright places.

Blooming or smearing may occur otherwise (which is not a

malfunction), and affect the endurance of sensor at the same

time.

●The sensor may be burned out by a laser beam, so when any

laser equipment is in using, make sure that the surface of

sensor will not be exposed to the laser beam.

●Do not place the camera in extremely hot, cold (the operating

temperature shall be-30°C ~+60°C , or -40°C ~ +60°C if the

Network Bullet Camera·Quick Start Guide

camera model has an “H” in its suffix), dusty or damp locations,

and do not expose it to high electromagnetic radiation.

●To avoid heat accumulation, good ventilation is required for

operating environment.

●Keep the camera away from liquid while in use.

●While in delivery, the camera shall be packed in its original

packing, or packing of the same texture.

●Regular part replacement: a few parts (e.g. electrolytic

capacitor) of the equipment shall be replaced regularly

according to their average enduring time. The average time

varies because of differences between operating environment

and using history, so regular checking is recommended for all

the users. Please contact with your dealer for more details.

●Improper use or replacement of the battery may result in

hazard of explosion. Replace with the same or equivalent type

only. Dispose of used batteries according to the instructions

provided by the battery manufacturer.

●If the product does not work properly, please contact your

dealer or the nearest service center. Never attempt to

disassemble the camera yourself. (We shall not assume any

responsibility for problems caused by unauthorized repair or

maintenance.)

Network Bullet Camera·Quick Start Guide

Table of Contents

1 Appearance Description ................................................................. 8

Type I Bullet Camera ....................................................... 8

Type II Bullet Camera ...................................................... 9

Type III Bullet Camera ................................................... 10

2 Installation.................................................................................... 12

Memory Card Installation.............................................. 12

Direct Mounting............................................................ 14

Mounting with a Junction Box....................................... 16

Mounting with a Gang Box............................................ 18

Network Cable Water-proof Jacket Installation (Optional)19

3 Setting the Network Camera over the LAN .................................. 22

Wiring ........................................................................... 22

Activating the Camera................................................... 23

Activation via Web Browser................................ 23

Activation via SADP Software ............................. 24

Modifying the IP Address .............................................. 26

4 Accessing via Web Browser .......................................................... 28

5 Operating via Guarding Vision App .............................................. 30

Enable Guarding Vision Service on Camera................... 30

Enable Guarding Vision Service via SADP Software30

Enable Guarding Vision Service via Web Browser31

Guarding Vision Setup................................................... 33

Adding Camera to Guarding Vision................................ 33

Initializing the Memory Card......................................... 35

Network Bullet Camera·Quick Start Guide

1Appearance Description

2T camera series has three appearance types. Type I supports no

memory card. Type II and Type III support memory card function, but

the positons of memory card slots on camera are different.

Type I Bullet Camera

Figure 1-1 Overview of Type I

Table 1-1 Description of Type I

No.

Description

Photoresistor

Lens

Sun Shield

Power Interface

Network Interface

Network Bullet Camera·Quick Start Guide

Type II Bullet Camera

DC12VIN

Figure 1-2 Overview of Type II

Table 1-2 Description of Type II

No.

Description

No.

Description

Lens

Network Interface (PoE)

Sun Shield

Memory Card Slot

Power Interface

Reset Button

Tabla de contenidos

Otros manuales de Cámara de seguridad de HIK VISION

HIK VISION

HIK VISION TURBO HD D3T Series Manual de usuario

HIK VISION

HIK VISION ECI-B14F2 Manual de usuario

HIK VISION

HIK VISION AE-VC1B11-ISF Manual de usuario

HIK VISION

HIK VISION HiLook D1 Series Manual de usuario

HIK VISION

HIK VISION DS2CD2725FWDIZS Manual de usuario

HIK VISION

HIK VISION DS-2TD2667-15/PY Manual de usuario

HIK VISION

HIK VISION NETWORK CAMERA Manual de usuario

HIK VISION

HIK VISION DS-2CD2146G1-IS Manual de usuario

HIK VISION

HIK VISION I0M1000 Manual de usuario

HIK VISION

HIK VISION DS-2TD2667-35/PY Manual de usuario

HIK VISION

HIK VISION iDS-2CD7 G0 Series Manual de usuario

HIK VISION

HIK VISION UD02330B Manual de usuario

HIK VISION

HIK VISION PanoVu Manual de usuario

HIK VISION

HIK VISION DS-2TD2628-7/QA/GLT Manual de usuario

HIK VISION

HIK VISION DS-2CD20x2-I Manual de usuario

HIK VISION

HIK VISION UD08391B Manual de usuario

HIK VISION

HIK VISION DS-2CE59U1T-VPIT3ZF Manual de usuario

HIK VISION

HIK VISION DS-2CE56D0T-IRP Manual de usuario

HIK VISION

HIK VISION iDS-2CD9396-BIS Manual de usuario

HIK VISION

HIK VISION DS-2XE6126FWD-HS Manual de usuario

HIK VISION

HIK VISION iDS-TCM203-A Manual de usuario

HIK VISION

HIK VISION DS-2CD3086G2-IS Manual de usuario

HIK VISION

HIK VISION H5T Manual de usuario

HIK VISION

HIK VISION TurboHD H0T Series Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario