HIGHLEAD GC0318-1A Manual de instrucciones

HEAVY DUTY TOP AND BOTTOM FEED

LOCKSTITCH SEWING MACHINE

GC0318-1A series

Instruction Manual

Parts Catalog

HANGHAI BIAOZHUN HAILING SEWING MACHINERY CO., LTD

—1 —

CONTENTS

1.Instruction Manual

1. MAIN SPECIFICATIONS………………………………………….…………………………………………2

2. INSTALL THE MOTOR……………………………………………………………………………………...2

3. CONNECT THE CLUTCH LEVER WITH THE PEDAL…………………………………………………...2

4. PREPARATION AND LUBRICATION………………………………………………………………………3

5. REPLACE NEEDLES………………………………………………………………………………………...3

6. NEEDLE, THREADAND MATERIAL TO BE SEWN……………………………………………………..4

7. RUN-IN OPERATION………………………………………………………………………………………..4

8. THREADING…………………………………………………………………………………………………5

9. WINDING ADJUSTMENT…………………………………………………………………………………..6

10. SET STITCH LENGTHAND REVERSE FEEDING………………………………………………………..7

11. POSITION PRESSER BAR…………………………………………………………………………………..7

12. ADJUST THE PRESSURE OF PRESSER EOOT……………………………………………………………8

13. ADJUST THREAD TENSION……………………………………………………………………………….8

14. ADJUST THREAD TAKE-UP SPRING……………………………………………………………………..9

15. ADJUST THREAD GUIDE AND THREAD TENSION…………………………………………………...10

16. TIME NEEDLE TO ROTAING HOOK……………………………………………………………………..11

17. REPLACE ROTATING HOOK……………………………………………………………………………...12

18. ADJUST THE HEIGHT OF FEED DOG…………………………………………………………………...12

19. ADJUST THE POSITION OF FEED DOG…………………………………………………………………13

20. TIME FEED MOTION TO NEEDLE MOTION……………………………………………………………13

21. ADJUST OPENING TIME OF THE TENSION DISCS……………………………………………………14

22. LUBRICATION ADJUSTMENT……………………………………………………………………………15

23. REGULAR CLEANING…………………………………………………………………………………….16

2.Parts Catalog

A. ARM BED AND ITS ACCESSORIES…………………………………………………..……………………17

B. NEEDLE BAR AND TAKE-UP、ARM SHAFTAND VERTICAL SHAFT MECHANISM………...….….20

C. STITCH REGULATOR MECHANISM……………………………………………………………….……...23

D. FEEDING AND FEED LIFTING MECHANISM..……………………………………………..…….……...25

E. PRESSER FOOT MECHANISM………...………………………………………………………………..….27

F. PRESSER LIFTING、FEEDING MECHANISM…………………………………………………….………29

G. LUBRICATION MECHANISM ………….………………………………………………………………… 32

H. OIL RESERVOIR AND OTHER ACCESSORIES……………………………………………………...…... 34

—2 —

1. MAIN SPECIFICATIONS

1) Sewing material: Light-Medium material

2) Max. sewing speed: 2000 spm.

3) Stitch length: 0-10mm.

0-5mm

4) Needle bar stroke: 35mm.

5) Presser fool lift: 6mm (by hand) 13mm (by knee ).

6) Needle: DP×17 No.18-No.22

DP×5 No.14-No.18

7) Lubrication: Automatic

8) Reverse feeding mechanism: Have

2.INSTALLTHE MOTOR ( Fig.1 )

Align Motor Pulley Groove ( B ) and Balance Wheel Groove ( A ) by moving the motor leftward or

rightward.

3. CONNECT THE CLUTCH LEVER WITH THE PEDAL ( Fig.2 )

1) The optimum tilt angle of pedal ( A ) is approximately 15 deg.

2) Adjust Clutch Cover ( D ) so that Clutch-Lever ( C ) and Draw Bar ( B ) run in line.

3) The balance wheel should rotate counter-clockwise when viewed from the outside of Balance

Wheel ( G ). The direction of the motor pulley rotation can be reversed by reversing ( turning

over 180 deg .) the power plug of the motor.

4) Adjust the tension of V-belt ( F ) by

turning Motor Vertical Position Screw ( E ).

The proper tension of the V-belt is a slack

of 10-20mm when the belt is depressed at

the center of the belt by finger.

Fig.1

Fig.2

—3 —

4. PREPARATION AND LUBRICATION ( Fig.3 )

1) Cleaning the machine

Before leaving the factory, the machine parts are coated with rust-preventive grease, which may be

hardened and contaminated by dust during storage and shipment. This grease must be removed with gasoline.

2) Examination

Though every machine is confirmed by strict inspection and test before leaving the factory, the machine

parts may be loose or deformed after long distance transportation with jolt. A thorough examination must be

performed after cleaning the machine. Turn the balance wheel to see if there is running obstruction, parts

collision, uneven resistance or abnormal noise. If these exist, adjustment must be made accordingly before run-in

operation.

3) Oiling

(1) Required amount of oil.

Line ( A ) on the oil reservoir: Max. oil level.

Line ( B ) on the oil reservoir: Min. oil level.

If oil level goes down under line ( B ),

oil cannot be distributed to each part of the machine,

thus causing the parts a seizure.

(2) Replenishing

Always use only No.18 special machine oil

for high speed sewing. Be sure to replenish oil to

Line ( A ) before starting operation.

(3) Replacing oil

To replace oil, remove Screw ( C ) to drain oil. After completely draining off oil, clean the oil reservoir and

securely tighten Screw ( C ), then fill the reservoir with fresh oil.

5. REPLACE NEEDLES ( Fig.4 )

Turn the balance wheel to lift needle bar to the upper end of its stroke. Loosen Needle Clamp Screw 1.

While keeping the long groove of the needle leftward fully insert the needle shank up to the bottom of the needle

socket. Then tighten Needle Clamp Screw A.

Note: Fig. ( b ): insufficient insertion.

Fig. ( c ): wrong direction of long groove.

Fig.3

Fig.4

—4 —

6. NEEDLE, THREAD AND MATERIALTO BE SEWN

Needle Size Thread Number Material

No.14 No.60-No.65 cotton, Woolen

No.16 No.30-No.50 Muslin,Woolen,Tarpaulin,Thin Leather

No.22 Medium leather,Canvas

7. RUN-IN OPERATION ( Fig. 5 )

Run-in operation is required for a new sewing machine, or a sewing machine left out operation for a

considerable length of time.

1) Remove Red Rubber Plugs (A ) on the top of the arm and replenish sufficient amount of oil.

2) Lift Presser Foot ( B ).

3) Run the machine at a low speed ( 2000-2500spm ) to check oil distributing condition through Oil Check

Window ( C ).

4) Perform run-in operation at 2000-2500spm for 30minutes. After a lapse of one month of service during

which the working speed is increased gradually and the machine runs sufficiently well, the high speed 5000spm

can be adopted according to the nature of the work.

Fig.5

—5 —

8. THREADING ( Fig.6 )

To thread the needle thread, raise needle bar to the upper end of its stroke, lead the thread from spool and

perform threading as shown in Fig.6 . To draw the bobbin thread, hold the end of the needle thread and turn the

balance wheel to lower the needle bar and then to lift it to its highest position. Pull the needle thread and the

bobbin thread is drawn up. Put the ends of needle thread and bobbin thread frontward under presser foot.

Fig.6

—6 —

9. WINDINGADJUSTMENT ( Fig.7 )

1) The wound bobbin thread should be neat and tight, if not, adjust the winding tension by turning Tension

Stud Nut ( A ) of bobbin winder tension bracket.

Note: nylon or polyester thread should be wound with little tension, otherwise, Bobbin ( D ) might break or

deform.

2) When the wound thread layer does not present a cylindrical shape as shown in Fig.7 ( a ), loosen Set

Screw ( B ) of bobbin winder tension bracket and slide Bracket ( C ) leftward or rightward. If thread is wound as

shown in Fig.7 ( b ), move the bracket rightward, but if thread is wound as shown in Fig.7 ( c ), move the bracket

leftward.

After adequately positioning the bracket, tighten Set Screw ( B ).

3) Do not overfill the bobbin. The optimum length of thread will fill about 80% of bobbin capacity. This can be

adjusted byAdjusting Screw ( E ) of bobbin winder stop latch.

Fig.7

—7 —

10. SET STITCH LENGTH AND REVERSE FEEDING ( Fig.8 )

1) Stitch length can be set by turning Dial ( A ).

2) The figures on Face ( B ) of dial show stitch length in mm.

3) Reverse feeding starts when Reverse Feed Lever ( C ) is depressed, and the machine will feed forward

again if Reverse Feed lever ( C ) is released.

11.POSITION PRESSER BAR ( Fig.9 )

1) Loosen lock Nut ( E ) and Pressure Regulating Thumb Screw ( A ).

2) Remove rubber plug from Face Plate ( B ).

3) Loosen Screw ( C ) and adjust the position of Presser Bar ( D ) till the presser foot is 6 mm above the

throat plate will the presser foot lifted to its highest.

4) Tighten Screw ( C ) and put in the rubber plug.

5) Tighten pressure Regulating Thumb Screw (A ) and Lock Nut ( E ).

Fig.8

Fig.9

—8 —

12. ADJUST THE PRESSURE OF PRESSER EOOT ( Fig.10 )

Pressure of presser foot is to be adjust in accordance with thickness of materials to be sewn.

First loosen Lock Nut ( A ). For heavy materials, turn the pressure regulating thumb screw as shown in

Fig.10 ( a ) to increase the pressure, while for light materials, turn the pressure regulating thumb screw as shown

in Fig.10 ( b ) to decrease the pressure. Then tighten Lock Nut ( A ).

The pressure of presser foot is recommended to be less as long as normal feeding is ensured.

13. ADJUST THREAD TENSION ( Fig.11,12 )

In principle, thread tension is to be adjusted in accordance with materials, thread and other factors.

In practice, thread tension is adjusted according to the stitches obtained. The needle thread tension should

be adjusted with reference to the bobbin thread tension. Turn Tension Spring Regulating Screw ( A ) of bobbin

case clockwise for more tension, or turn the screw counter-clockwise for less tension.

It is common practice to test the bobbin test the bobbin thread tension as shown in Fig.12 . Hold the end of

the thread from delivery eye. If the bobbin case is falling slowly, the proper tension is obtained. The needle

thread tension can be adjusted by setting ( 1 ) the take-up spring tension. ( 2 ) the thread take-up spring stroke

and ( 3 ) tension spring. All these adjustments will be described in the following.

Fig.10

Fig.11 Fig.12

—9 —

14. ADJUST THREAD TAKE-UPSPRING ( Fig.13,14 )

1) Adjusting the thread take-up spring tension

Loosen Set Screw ( A ), turn Tension Stud ( B ) clockwise to increase the spring tension, or turn the stud

counter-clockwise to decrease the spring tension. After the adjustment, be sure to tighten Set Screw ( A ). The

thread take-up spring tension should be about 30g. To Attain this. First loosen Set Screw ( A ), turn Tension Stud

( B ) counter-clockwise to decrease the tension of Thread Take-up Spring ( C ) to zero, then turn Tension Stud

( B ) clockwise until Spring ( C ) comes to the notch of thread tension regulating bushing, and again turn Tension

Stud ( B ) halfway back ( counterclockwise ) After the adjustment. Tighten Set Screw (A ).

2) Adjusting the thread take-up spring stroke

Loosen Set Screw ( B ), turn Stud ( C ) clockwise to increase the stroke or turn Stud ( C )

counter-clockwise to decrease the stroke.After the adjustment, tighten Set Screw ( B ).

Before leaving the factory, the thread take-up spring has properly been adjusted. Readjustment is needed

only in the case of special material or special thread.

Fig.13

Fig.14

Otros manuales para GC0318-1A

Tabla de contenidos

Otros manuales de Máquina de coser de HIGHLEAD

HIGHLEAD

HIGHLEAD GC318-2A Manual de usuario

HIGHLEAD

HIGHLEAD GC0318-1 Manual de instrucciones

HIGHLEAD

HIGHLEAD GA1398-1 Manual de usuario

HIGHLEAD

HIGHLEAD GC0318-2A Manual de usuario

HIGHLEAD

HIGHLEAD GA2688-1 Manual de usuario

HIGHLEAD

HIGHLEAD GC2008-M Manual de usuario

HIGHLEAD

HIGHLEAD GC24698-2B Manual de usuario

HIGHLEAD

HIGHLEAD GC6-28-1 Manual de usuario

HIGHLEAD

HIGHLEAD GC1998-MCDZ Manual de usuario

HIGHLEAD

HIGHLEAD GC618-1 Manual de usuario

HIGHLEAD

HIGHLEAD GC20688-BDCE Series Manual de instrucciones

HIGHLEAD

HIGHLEAD GC24698-BRHL Manual de usuario

HIGHLEAD

HIGHLEAD GG0068-1 Manual de usuario

HIGHLEAD

HIGHLEAD GA2698-1 Manual de instrucciones

HIGHLEAD

HIGHLEAD GC20528 series Manual de usuario

HIGHLEAD

HIGHLEAD GM288-3 Manual de usuario

HIGHLEAD

HIGHLEAD GC24608-2 Manual de instrucciones

HIGHLEAD

HIGHLEAD GC188-MC Manual de usuario

HIGHLEAD

HIGHLEAD GC20698-6 Manual de usuario

HIGHLEAD

HIGHLEAD GM700 Series Manual de usuario

HIGHLEAD

HIGHLEAD YXP-18 Manual de usuario

HIGHLEAD

HIGHLEAD GK0058-AD Manual de usuario

HIGHLEAD

HIGHLEAD GK0088 Manual de usuario

HIGHLEAD

HIGHLEAD DY-850 Manual de usuario

Manuales populares de Máquina de coser de otras marcas

Riccar

Riccar RL634DE Manual de usuario

Singer

Singer 2517 Manual de usuario

Pfaff

Pfaff 3307-1 SERIES Manual de usuario

Janome

Janome Quilt Maker Pro 18 VERSA Manual de usuario

Siruba

Siruba C007JP Manual de usuario

Husqvarna Viking

Husqvarna Viking Designer SE Manual de usuario

Singer

Singer 148-5 Manual de usuario

IKEA

IKEA SY Manual de usuario

Pfaff

Pfaff 571 Manual de usuario

Singer

Singer 15-91 Manual de usuario

Brother

Brother BB370 Manual de usuario

Pegasus

Pegasus WT100 Series Manual de usuario

Reliable

Reliable 7100DB Manual de usuario

Pfaff

Pfaff 937 Manual de usuario

Singer

Singer 6038 Manual de usuario

Singer

Singer 413K Manual de usuario

Pfaff

Pfaff 1471 E1 Manual de usuario

Kenmore

Kenmore 16677 - Serger Sewing Machine Manual de usuario