HIGHLEAD GA2688-1 Manual de usuario

SHANGHAI BIAOZHUN HAILING SEWING MACHINERY CO.,LTD.

GA2688-1

Cylindrical Bed Extra-Heavy Duty

Compound-Feed Lockstitch Sewing Machine

Instruction Manual

Parts Catalog

≡CONTENT≡

1. PRECAUTIONS BEFORES STARTING OPERATION ……………………………………………………………1

■Safety precautions………………………………………………………………………………………1

■Precautions before starting operation…………………………………………………………… 1

■Precautions for operating conditions …………………………………………………………… 1

2. SPECIFICATION ……………………………………………………………………………………………1

3. PREPARATION FOR OPERATION ……………………………………………………………………………2

■Cleaning the machine …………………………………………………………………………………2

■Examination………………………………………………………………………………………………2

■Lubrication………………………………………………………………………………………………2

■Testing……………………………………………………………………………………………………2

4. HOW TO ATTACH A NEEDL………………………………………………………………………………… 2

5. WINDING OF BOBBIN THREAD………………………………………………………………………………3

6. ADJUSTMENT OF THE BOBBIN WINDER ……………………………………………………………………3

■In case of uneven winding……………………………………………………………………………3

■Winding amount of thread…………………………………………………………………………… 3

■Winding strength……………………………………………………………………………………… 3

7. THREADING …………………………………………………………………………………………………4

8. REMOVING AND INSERTING THE BOBBIN …………………………………………………………………4

■Removing …………………………………………………………………………………………………4

■Installation ……………………………………………………………………………………………4

9. ADJUSTING THE THREAD TENSION…………………………………………………………………………4

■Tension of the Upper thread…………………………………………………………………………5

■Tension of the lower thread…………………………………………………………………………5

10. ADJUSTMENT OF PRESSER PRESSURE ……………………………………………………………………5

11. ADJUSTMENT OF WALKING FOOT AND PRESSER FOOT …………………………………………………6

12. ADJUSTMNET OF STITCH LENGTH

AND FORWARD/BACKWARD SEWING ………………………………………………………………………6

13. FEED DOG HEIGHT ………………………………………………………………………………………6

14. ADJUSTING THE HEIGHT OF THE NEEDLE BAR …………………………………………………………7

—1 —

1. PRECAUTIONS BEFORES STARING OPERATION

1) Safety precautions：

(1) When turning the power on, keep your hands and fingers away from the area around/under the needle

and the area around the pulley.

(2) Power must be turned off when the machine is not in use, or when the operator leaves the seat.

(3) Power must be turned off when tilting the machine head, installing or removing the “V” belt, adjusting

the machine, or when replacing.

(4) Avoid placing fingers, hairs, bars etc., near the pulley, “V” belt, bobbin winder pulley, or motor when

the machine is in operation.

(5) Do not insert fingers into the thread take-up cover, under/around the needle, or pulley when the machine

is in operation.

(6) If a belt cover, finger guard, eye guard are installed, do not operate the machine without these safety

devices.

2) Precautions before starting operation：

(1) If the machine’s oil pan has an oil sump, never operate the machine before filling it.

(2) If the machine is lubricated by a drop oiler, never operate the machine before lubricating.

(3) When a new sewing machine is first turned on, verify the rotational direction of the pulley with the

power on. (The pulley should rotate counterclockwise when viewed from the pulley)

(4) Verify the voltage and (single or three) phase with those given on the machine nameplate.

3) Precautions for operating conditions：

1) Avoid using the machine at abnormally high temperatures（35℃or higher）or low temperatures（5℃or

lower）.

2) Avoid using the machine in dusty conditions.

2、SPECIFICATION

Max. sewing speed (r.p.m) 800 r.p.m

Needle No. DY×3 26#

Needle bar stroke (mm) 56

Thread take-up lever stroke (mm) 96

Stitch length (mm) 0-11

Presser-foot stroke By hand (mm) 13

By knee (mm) 20

Shuttie hook KSP-204N

Lubrication Manual

—2 —

3、PREPARATION FOR OPERATION

（1）Cleaning the machine

Before leaving the factory, the machine parts are coated with rust-preventive grease, which may be

hardened and contaminated by dust during storage and shipment. This grease must be removed with gasoline.

（2）Examination

Though every machine is confirmed by strict inspection and test before leaving the factory, the machine

parts may be loose or deformed after long distance transportation with jolt. A thorough examination must be

performed after cleaning the machine. Turn the pulley to see if there is running obstruction, parts collision,

uneven resistance or abnormal noise. If these exist, adjustment must be made accordingly before run-in

operation.

（3）Lubrication (Fig.1)

When a new sewing machine is used for the first time, or sewing machine left out of use for considerably

long time is used again, replenish a suitable amount of oil to the portions indicated by arrow in below figure.

CAUTION：Please use white spindle oil.

Always keep the presser lifted before attempting a dry run.

（4）Testing

In order to get the best working situation, run the sewing machine in a low speed for about 1 month after

lubricated fully. Then increase the speed to the need one.

4、HOW TO ATTACH A NEEDLE (Fig.2)

CAUTION：Before using the following procedures, be sure to turn the power switch off.

The needle used by this sewing machine is DY×3 26#。During operation, proper needle can be chosen

according to the sewing thread.（the sewing thread should be able to pass the pinhole.）

Fig.1

—3 —

5、WINDING OF BOBBIN THREAD (Fig.3)

(1) Push the bobbin ③on the bobbin winder

shaft as far as it will go.

(2) Bring the thread forward toward the bobbin

and wind from below in clockwise direction

several times around the bobbin.

(3) Push the lever ⑤toward other side so that

the driving wheel and driven wheel will engage

and then start the machine.

(4) The driven wheel will automatically be free

from the driving wheel and stop after the bobbin

is filled with thread.

6、ADJUSTMENT OF THE BOBBIN WINDER (Fig.3)

(1) In case of uneven winding

If the thread dose not wind evenly on the bobbin, loosen the nut ①and move the bracket ②to the

right or to the left as may be required, then tighten the nut.

(2) Winding amount of thread

Adjusting ⑥can increase or decrease the amount of thread wound on the bobbin.

(3) Winding strength

Strength of the winding can be adjusted with the nut ①.

Fig.2

Fig.3

—4 —

7、THREADING (Fig.4)

Raise the needle bar to its highest position and route the upper thread in the order illustrated below.

8、REMOVINGAND INSERTING THE BOBBIN

(1) Removing:

Open the shuttle race cap and the bobbin holder, then take out the bobbin.

(2) Installation:

Put the bobbin in the rotary hook case, Permit about 5 cm of bobbin thread to hand down freely. Install

the bobbin in the bobbin case so that the thread wound direction is clockwise. Then close the rotary hook

and the shuttle race cap.

9、ADJUSTING THE THREAD TENSION (Fig.5)

For ordinary stitching, the tension of the upper and the lower threads should be equal.

Fig.4

—5 —

(1) Tension of the Upper thread

Before adjusting the tension of the upper thread, be sure that presser foot is let down. To adjust tension,

turn serrated nut on tension device to the right (clockwise) to increase tension and to the left (counter-clockwise)

if you desire to decrease the tension.

(2) Tension of the lower thread

The lower thread tension is controlled by the larger screw near the end of the spring at the outside of the

bobbin case. Turning this screw to the right (clockwise) will increase the thread tension, while turning it to the

left (counter-clockwise) will decrease the tension.

10、ADJUSTMENT OF PRESSER PRESSURE (Fig.6)

(1) Pressure should be adjusted according to the

material to be sewn.

(2) Pressure on both the walking foot and the

presser foot can be adjusted. (The adjusting

screw has been set before shipment.)

(3) Sewing pressure should be adjusted to the

minimum required strength.

Fig.6

Fig.5

—6 —

11、ADJUSTMENT OFWALKING FOOTAND PRESSER FOOT (Fig.7)

(1) The alternating movement on the walking foot

and presser foot can be adjusted by changing

the position relations of the parts of the presser

foot lifting mechanism.

(2) Changing the position relation of the connecting

link 2 and the crank 3 can complete the adjustment.

(3) Adjustment should be changed according to the

thickness of the material to be sewn..

12、ADJUSTMENT OF STITCH LENGTH AND FORWARD/BACKWARD

SEWING (Fig.8)

(1) Adjusting the stitch length adjusting bolt can

change the stitch length.

(2) Stitch length can be adjusted between 0-11mm.

(3) Setting the stitch length adjusting bolt above

“0”can backstitch.

13、FEED DOG HEIGHT (Fig.9)

The feed dog should be 1.5 mm higher than the vertex

of the needle plate. Adjustment of the feed dog height

can be done as follows:

(1) Turn the machine pulley so as to raise the feed dog

to its highest point.

(2) Loosen the screw of the feed dog and adjust the

height by raising or lowering it. Then tighten the screw.

Fig.7

Fig.8

Fig.9

—7 —

14、ADJUSTING THE HEIGHT OF THE NEEDLE BAR (Fig.10)

When the needle bar is at its highest point, normally

the measurement between the highest point of the

needle plate and the needlepoint is 28 mm. When this

distance need to be adjusted, the steps is as follows:

(1) Take down the face plate, adjust the needle bar to

its highest position.

(2) Loosen the screw of needle bar connecting stud

screw.

(3) Adjust the needle bar to the right position.

(4) Tighten the screw.

Fig.10

— 8 —

A.ARM BED AND ITS ACCESSORIES

Otros manuales para GA2688-1

Tabla de contenidos

Otros manuales de Máquina de coser de HIGHLEAD

HIGHLEAD

HIGHLEAD GC0618-1-SC Manual de instrucciones

HIGHLEAD

HIGHLEAD GC20618-1DZ Manual de instrucciones

HIGHLEAD

HIGHLEAD GG0068-1 Manual de usuario

HIGHLEAD

HIGHLEAD GM700 Series Manual de usuario

HIGHLEAD

HIGHLEAD YXP-18 Manual de usuario

HIGHLEAD

HIGHLEAD GC20688 Series Manual de usuario

HIGHLEAD

HIGHLEAD GC618-1 Manual de usuario

HIGHLEAD

HIGHLEAD GC1918 -MDZ Manual de usuario

HIGHLEAD

HIGHLEAD GC20518 Series Manual de usuario

HIGHLEAD

HIGHLEAD GK500 Series Manual de instrucciones

HIGHLEAD

HIGHLEAD GC20618 Series Manual de instrucciones

HIGHLEAD

HIGHLEAD GA1398-1 Manual de usuario

HIGHLEAD

HIGHLEAD GC0318-1A Manual de usuario

HIGHLEAD

HIGHLEAD GC22618 Manual de instrucciones

HIGHLEAD

HIGHLEAD GC20638-25 Manual de usuario

HIGHLEAD

HIGHLEAD GC0518-MC Manual de instrucciones

HIGHLEAD

HIGHLEAD HLK-1510 Manual de usuario

HIGHLEAD

HIGHLEAD GC24628-1 Manual de usuario

HIGHLEAD

HIGHLEAD GK600 SERIES Manual de instrucciones

HIGHLEAD

HIGHLEAD GK0058-AD Manual de usuario

HIGHLEAD

HIGHLEAD GC24698-1L Manual de usuario

HIGHLEAD

HIGHLEAD GC24018 Manual del instalador

HIGHLEAD

HIGHLEAD GC2698-2 Manual de usuario

HIGHLEAD

HIGHLEAD GC1998-MCDZ Manual de usuario

Manuales populares de Máquina de coser de otras marcas

Riccar

Riccar RL634DE Manual de usuario

Singer

Singer 2517 Manual de usuario

Pfaff

Pfaff 3307-1 SERIES Manual de usuario

Janome

Janome Quilt Maker Pro 18 VERSA Manual de usuario

Siruba

Siruba C007JP Manual de usuario

Husqvarna Viking

Husqvarna Viking Designer SE Manual de usuario

Singer

Singer 148-5 Manual de usuario

IKEA

IKEA SY Manual de usuario

Pfaff

Pfaff 571 Manual de usuario

Singer

Singer 15-91 Manual de usuario

Brother

Brother BB370 Manual de usuario

Pegasus

Pegasus WT100 Series Manual de usuario

Reliable

Reliable 7100DB Manual de usuario

Pfaff

Pfaff 937 Manual de usuario

Singer

Singer 6038 Manual de usuario

Singer

Singer 413K Manual de usuario

Pfaff

Pfaff 1471 E1 Manual de usuario

Kenmore

Kenmore 16677 - Serger Sewing Machine Manual de usuario