High-End Technology F-20 Manual de usuario
1"
www.EJF.com"
High End Technology 90mm F-20
Assembly Manual
Specifications:
- Length: 57" 1430MM
- Wingspan: 29.5" 750MM
-Weight: 3lbs 6oz
- Full Intake/Exhaust ducting with NO cheater holes
- EDF - HET-9305 FAN
- Motor - HET-700-68-1400
- ESC ±HET-100HV
- Lipo ±10S±5000mah, 35C
- 8 servos ±2 ±Elevator, 2 ±Ailerons, 2±Flaps, 1 ±Rudder, 1 ±Steering
High%End%Technology%RC%Asia%Pacific%Ltd.%
Room$2202$Cheung$Tat$Centre$
18$Cheung$Lee$Street$Chaiwan$
Hong$Kong$
Phone:'852'2187'2622
www.HighEndRC.com"
2"
www.EJF.com"
Table of Contents
Introduction Pg 3
Out of the Box Pg.4
Wing Assembly Pg.5-7
Vertical Stabilizer and Rudder Assembly Pg.8-9
Elevator Assembly Pg.8- 10
Retract Mount Assembly Pg.11-14
Fan Mount Assembly Pg.14-15
Fan Unit and Thrust Tube Installation Pg.15-17
Final Equipment Placement Pg.13
Center of Gravity and Initial settings Pg.17-18
3"
www.EJF.com"
Introduction
Although the F-20 goes together very easily, there is still some construction involved, this is NOT a plane for
beginners, and you should have some experience with putting together ARFs. Please look carefully at the
pictures and explanations carefully before performing any work. There are many ways to build a plane, eg servo
mounting methods, it is up to the builder to fully test their airplane and flight controls before flight. As the
builder of the prototype airframe, I like to make servos serviceable as much as possible. Before you glue
anything to any surface, make sure it is clean and in the case of fiberglass parts, I sand first with 80 grit
sandpaper and then clean the area where glue will be applied. I often glue servos to surfaces, I make sure to use
tape around the servo so that when the servo is moved, you can also remove the glue by removing the tape. Try
to use a Single piece of tape around the servo as to provide more strength.
You will require some additional items before you can complete your F-20 constructions, along with some
common model building tools. The amount of channels required is a minimum of 6, but you have to be able to
mix and reverse channels, it is highly recommended that you have more than 6, the prototype model used a total
of 7, as follows: 1channles for flaps, 2 channel for elevators, 1 channel Rudder and otherwise you will DQG³<´
cable for Steering servo (I used a separate channel for steering), 1 channel retracts, 1 channel throttle
Additional Items Required
- HET-RC EDF9305 or similar
- Typhoon EDF motors 700-68-1400 or suitable for your power requirements
- HET-100HV
- 8 micro digital servos (2X Aileron, 2X Elevator, 2X Flaps, 1 Rudder and 1 Steering)
- Retracts
-6-8 ch. Computer Radio system w/ 8 servos.
- Lipo battery (Suitable for your motor and ESC)
-5 or 30 minute epoxy
-micro balloons
-CA Glue w/ accelerator
-Velcro.
Standard Model airplane building tools:
-Drill or Dremel tool
-Pliers/cutter
-Scissor
-Xacto Knife
4"
www.EJF.com"
OUT OF THE BOX
PICTURE ON LEFT: Top side of the plane place together for pictures. 1X fuselage, 2X Wings, 1X vertical stab and
rudder, 2X elevators, 2X Missile Rails, Ailerons, flaps and missiles not shown in the pictures
PICTURE ON RIGHT: Bottom of the airplane, Landing gear and servo locations already built into the plane.
PICTURE ON LEFT: Few formers needed to build, top and center are battery tray, the rest are Fan Mounting formers.
PICTURE ON RIGHT:, Vertical Fin and Rudder. Below are the Missile Rails, Missiles, Canopy Frame and Clear Canopy
.
5"
www.EJF.com"
WING CONSTRUCTION
The first thing to do is to sand all parts that will be glued; I used 80 grit sandpaper to remove the paint from the Fuselage
and then cleaned it with cleaning alcohol (denatured alcohol). The wing spar will need to be lightly sanded and so will the
wing; you may elect to remove some of the covering where the wing glues on to the fuselage. This is left to the discretion
of the builder. My Fuselage did not have a slot for the Aileron servo wire to go through, I used the wing to measure out
where the servo would exit and cut a slot. NOTE: When I received the F-20, the wings had already been glued to the
fuselage, I will use some pictures from the HET F-16 as reference.
PICTURE ON LEFT: The example above is from the HET F-16, but the procedure is the same. Sand the Spar lightly and
I used 30 minute epoxy, I used a small stick that can push epoxy inside the wing and provide glue all over the cavity in the
wing.
PICTURE ON RIGHT: Do not try to force the wing spar too far into the wing; you should feel it stop once it reaches
about 50% into the wing, clean off excess glue from where the spar meets the wing. Notice that there is no access for the
VHUYRZLUHRQWKHIXVHODJHLILW¶VQRWSUHVHnt already; this is the perfect time to cut one out.
PICTURE ON LEFT: The whole cut out after the wing was joined, it is best to cut it on the fuselage and the wing before
you glue the wing on the body.
PICTURE ON RIGHT: Test fit the wing with the Spar in place and make sure there are no GAPS before you glue the
wing to the fuselage. Trim the spar if needed. NOTE: Carbon Fiber Spar is very brittle, sand or cut the spar with dremmel
and cut off wheel, DO NOT use pliers, scissors or anything that will compress (crunch) the spar. Once you are satisfied
with the fit of the wing, glue the wings to the airplane with 30 min epoxy or glue of your choice.
6"
www.EJF.com"
WINGS CONTINUED
PICTURE ON LEFT: Check the Aileron and Rudder hinge slots to make sure the hinges fit properly. If needed, use and
exacto knife open up further just make sure to get them in the middle of the leading edge of the Aileron or Flap.
PICTURE ON RIGHT: I am checking the Hinge Slot or hole in the HET F-16 Aileron.
PICTURE ON LEFT: When the hinges are glued, I measure the pushrod to mark the servo location. Measure your servo
wire and add servo extension wire to reach your receiver.
PICTURE ON RIGHT: When gluing servos on a model airplane, I like to protect them using tape, I used a single piece of
tape that is able to wrap around the servo at least twice. I glued the Aileron servos directly to the wing. This example is
the HET-F16.
7"
www.EJF.com"
WINGS CONTINUED
PICTURE ON LEFT: With the servo in place I make balsa mounts for the cover.
PICTURE ON RIGHT: Aileron is done.
PICTURE ON LEFT: Made a mount for the Flap servo to have it removable.
PICTURE ON RIGHT: Glue in the Mount and Servo to the wing. NOTE the routing of the Aileron and Flap servo wiring
is not in the fuselage.
8"
www.EJF.com"
VERTICAL FIN / RUDDER
PICTURE ON LEFT: Use your servo to measure and cu the access for the servo, there are many ways to mount a servo.
PICTURE ON RIGHT: If you want to be able to service/access your servo, install it from inside the fuselage, you can
always remove and make changes. Two pieces of wood where glues to hold the servo screws in place.
PICTURE ON LEFT: Rudder Servo as viewed from inside the Fuselage.
PICTURE ON RIGHT: Place the Vertical FIN behind the servo so you can measure where you will need access for your
control Horn. At this point your Rudder servo should be centered using your radio.
9"
www.EJF.com"
PICTURE ON LEFT: Servo Control Horn Cut out on the Vertical stab
PICTURE ON RIGHT: Sand the fuselage and the inside of the Vertical Fin, the example above is the F-16 shown for
illustration. Test fit everything and then satisfied, Glue the vertical fin the body.
.
PICTURE ON LEFT: Connect your servo to the Rudder now that your vertical fin is glued to the body.
10"
www.EJF.com"
ELEVATORS
PICTURE ON LEFT: The elevator already comes built and ready to be mounted to the fuselage. The control Horn is
glued and then uses two screws for additional support, the two screws for the control horn can bind with the fuselage.
Sand the elevator rod lightly making sure you do NOT bend the rod.
PICTURE ON RIGH: You will need to add washers or spacers until your elevator moves freely, when satisfied with the
fit, Glue in the elevator to the rod with Epoxy.
PICTURE ON RIGHT: It is best to install the servos in the fuselage while no other equipment is in, this way you can have
access from the fan cover area and the rear of the plane. Add servo extensions as needed to reach your receiver and then
Mount the elevator servos to the bottom of the body/fuselage.
PICTURE ON LEFT: Once you mounted the servo, mark the location of your control horn and cut out the control horn
window. If you want to cut small openings use one of the servo covers from the wing to mark and cut-out on the bottom
of the fuselage.
Tabla de contenidos
Otros manuales de Juguete de High-End Technology
