HID VertX EVO V2000 Manual de usuario

VertX EVO V2000

Installation Guide

72000-901, Rev. A.5

July 2016

hidglobal.com

Page 2 of 22 July 2016

VertX EVO V2000 Installation Guide, 72000-901, Rev. A.5

form without the prior written permission of HID Global Corporation.

Trademarks

HID GLOBAL, HID, the HID logo, iCLASS, and VertX, are the trademarks or registered

trademarks of HID Global Corporation, or its licensors, in the U.S. and other countries.

Revision History

Date Description Version

July 2016 Update to Section 3.4, wiring warning. A.5

February 2016 Content reformatted to standard template. A.4

February 2016 Update Global Contacts information and Section 5.1.4.1, password

configuration information. A.3

April 2012 Expanded VertX Installation Guide. A.2

October 2011 VertX installation wiring and settings. A.1

Contacts

For additional offices around the world, see www.hidglobal.com corporate offices.

North America Asia Pacific

611 Center Ridge Drive

Austin, TX 78753

USA

Phone: 866-607-7339

Fax: 949-732-2120

19/F 625 King’s Road

North Point, Island East

Hong Kong

Phone: 852 3160 9833

Fax: 852 3160 4809

Europe, Middle East and Africa Brazil

Haverhill Business Park Phoenix Road

Haverhill, Suffolk CB9 7AE

England

Phone: 44 (0) 1440 711 822

Fax: 44 (0) 1440 714 840

Condomínio Business Center

Av. Ermano Marchetti, 1435

Galpão A2 CEP 05038-001

Lapa - São Paulo/SP

Brazil

Phone: 55 11 5514-7100

HID Global Customer Support: www.hidglobal.com/support

VertX EVO V2000 Installation Guide, 72000-901, Rev. A.5

July 2016 Page 3 of 22

Contents

1Introduction..................................................................................................................................4

1.1 Parts List ................................................................................................................................................. 4

1.2 Product Specifications...................................................................................................................... 4

1.3 Cable Specifications........................................................................................................................... 4

2Overview ...................................................................................................................................5

3Connect ...................................................................................................................................6

3.1 What you need before getting started...................................................................................... 6

3.2 V2000...................................................................................................................................................... 6

3.3 Mounting Instructions ....................................................................................................................... 6

3.4 Wiring VertX EVO................................................................................................................................7

4Contact ................................................................................................................................. 10

4.1 Discovery GUI (for DHCP Networks).........................................................................................10

4.2 Virtual Port............................................................................................................................................10

5Configure ................................................................................................................................. 12

5.1 VertX Communications.................................................................................................................... 12

5.1.1Configuration GUI Login.................................................................................................. 12

5.1.2 Basic Network Setup......................................................................................................... 12

5.1.3 Static Network ..................................................................................................................... 12

5.1.4 Host Communication Setup ........................................................................................... 12

5.1.5 Confirmation ......................................................................................................................... 13

6Communicate ............................................................................................................................. 14

Appendix: A Troubleshooting ................................................................................................. 14

A.1 System Status...................................................................................................................................... 15

A.2 Supplemental Configuration ......................................................................................................... 15

A.3 Configure ............................................................................................................................................... 15

A.4 System Time......................................................................................................................................... 15

A.5 Update System.................................................................................................................................... 16

A.6 Battery Replacement........................................................................................................................ 16

A.7 Network Defaults Jumper .............................................................................................................. 17

A.8 Firewall ................................................................................................................................................... 18

Appendix: B Regulatory............................................................................................................ 19

Appendix: C Configuration Checklist - Static .................................................................... 20

Appendix: D VertX Installation Worksheet ......................................................................... 21

Page 4 of 22 July 2016

VertX EVO V2000 Installation Guide, 72000-901, Rev. A.5

1Introduction

HID Global’s VertX EVO® open platform is flexible and scalable to permit economic and high

performance access control solutions for a wide range of applications. The VertX EVO V2000

interconnects through different sub-networks and protocols to a standard TCP/IP network with

the capability of a variety of applications.

For example, the VertX EVO V2000 Reader Interface / Access Controller is a cost-effective

method for two-way communication using Ethernet between a computer and a V2000.

1.1 Parts List

Description Quantity

VertX EVO V2000 (Reader Interface / Access Controller)

Note: Each VertX EVO V2000 has a plastic base and is covered with a plastic lid.

1 V2000

•

Lithium Battery 1

•Mounting screws 4

•2.2K EOL resistors 8 ea. V2000

•Quick Installation Guide 1

•

Installation Wiring Diagram Example 1

1.2 Product Specifications

Description Specification

Power Supply Input 12-24VDC

Maximum Current at 12-24VDC per Unit 1 Amp

Average Operating Current at 12VDC 625mA (with two R40 iCLASS Readers)

Reader Power Output 12VDC, 250mA each

Relay Outputs 30VDC, 2Amp, resistive

Operating Temperature Range 32°-120°F (0°- 49°C)

Humidity 5% to 85% non-condensing

1.3 Cable Specifications

Cable Type Length Specification

Input Circuits* 500 feet (150 m) 2-conductor, shielded, using ALPHA 1292C (22AWG) or

Alpha 2421C (18AWG), or equivalent.

Output Circuits* 500 feet (150 m) 2-conductor, using ALPHA 1172C (22AWG) or Alpha

1897C (18AWG), or equivalent.

Wiegand

500 feet (150 m) to

reader

ALPHA 1299C, 22AWG, 9-conductor, stranded, overall

shield.

Fewer conductors needed if all control lines are not used.

Ethernet 328 feet (100 m) Cat5, Cat5E, and Cat6

Power Supply

12-24 VDC IN ---- Refer to your Power Supply Installation Guide. Not

Provided.

* Minimum wire gauge depends on cable length and current requirements.

VertX EVO V2000 Installation Guide, 72000-901, Rev. A.5

July 2016 Page 5 of 22

2Overview

The following outlines what is required to install VertX EVO V2000 controller.

Page 6 of 22 July 2016

VertX EVO V2000 Installation Guide, 72000-901, Rev. A.5

3Connect

3.1 What you need before getting started

Prior to starting the installation, completely read this guide.

See Section Appendix: C Configuration Checklist - Static, and gather the information before

proceeding with these instructions.

CAUTION: VertX controllers are sensitive to Electrostatic Discharges (ESD).

Observe precautions while handling the circuit board assembly by using proper grounding

straps and handling precautions at all times.

To further protect against the harmful effects of EMC and transients, a functional

earth connection point is provided under two of the mounting screws. See silkscreen

symbols.

3.2 V2000

Verify the battery jumper is installed in the ON position, P10 connector.

3.3 Mounting Instructions

Always mount the V2000 controller in a secure area.1.

Battery Installation. See Section Appendix: A-A.6 Battery Replacement.2.

a. Remove the cover.

b. Insert the battery with the + (positive) side facing upwards under the prongs,

lowering the opposite side into place.

Mount using the four mounting screws provided or other appropriate fasteners.3.

Place the fasteners in the corner holes of the base.

Position the VertX EVO devices in such a way as to provide room for wiring, air-flow4.

and cable runs.

Replace the cover.5.

VertX EVO V2000 Installation Guide, 72000-901, Rev. A.5

July 2016 Page 7 of 22

3.4 Wiring VertX EVO

WARNING: VertX EVO V2000 is a NON-PoE device. DO NOT connect J1 (Ethernet port) to

a PoE capable port. This applies to both direct PoE Power Sourcing Equipment (Endspan

PSE) and PoE injector (Midspan PSE) equipment. Not all PSE's correctly detect Non-PoE-

capable devices, and such PSE's may not function as expected when connected to Non-

PoE equipment. If the only option is to connect the controller to a PoE enabled port,

disable power of the PoE port before connecting.

Note:Carefully peel the attached Warning Label from the bottom of the unit and leave the

label attached to the unit's cover for future reference.

CAUTION: Connectors on the VertX EVO devices are positioned to be mirror images and

are not interchangeable once the installation is complete. Therefore, you cannot unplug a

connector from one side and plug it into the corresponding connector on the other side.

Network Connection: Connect the VertX EVO V2000 to the network using a1.

standard Cat5 network patch cable. Connect one end of the Cat5 network patch

cable to the J1 (RJ-45) connector on the V2000 and the other end to the network

connection point (network jack, hub, switch, or router) on your site.

Note: Two LED lights exist on the RJ-45 connector. The green LED denotes Ethernet

Activity and the yellow LED denotes speed. When the Yellow LED is on, it indicates

100 Mbits per second. Another LED in-board is a Duplex LED, indicating duplex

communications are available.

Power and Alarm input connections (All VertX EVO units): Connect power by2.

providing appropriate DC input to the P7 connector. Appropriate DC input goes to

Pin 1 and ground to Pin 2. Batt Fail, AC Fail, and Tamper switch inputs are wired as

shown in the table. Connect the Bat Fail and AC Fail inputs to battery low/failure and

AC failure contacts provided on the power supply. Connect the Tamper input to a

tamper switch on the enclosure.

Pin # P7

1 12-24VDC

2 Ground

3 Bat Fail -

4 Bat Fail +

5 AC Fail -

6 AC Fail +

7 Tamper -

8 Tamper +

Page 8 of 22 July 2016

VertX EVO V2000 Installation Guide, 72000-901, Rev. A.5

Reader Connections: Connect Wiegand or clock-and-data interfaces to a V20003.

using the connection table shown. You can connect up to 10 signal lines for the

reader. Use as many of the signal lines as required for your reader interface.

Note: Connect the data return line to the same ground as the reader power if the

reader is not powered by the VertX units.

Pin # V2000 P1 V2000 P4

1 Reader Power Shield Ground

2 Ground Hold

3 Data 0 / Data Beeper

4 Data 1 / Clock Red LED

5 Data Return Green LED

6 Green LED Data Return

7 Red LED Data 1 / Clock

8 Beeper Data 0 / Data

9 Hold Ground

10 Shield Ground Reader Power

Output Connections (VertX EVO V2000):All Output connections are used for4.

general purpose controls. The following table shows where the various outputs are

located. Pin numbers shown use the convention “NO/C/NC”. For example, Output 1,

V2000: P3 Pin 1 is NO (Normally Open,) Pin 2 is C (Common,) and

Pin 3 is NC (Normally Closed).

Note: Relays are dry contact rated for 2Amps @ 30VDC, resistive.

Output Number V2000

1 P3 Pins 1/2/3 - Strike(lock) Relay 1

2 P3 Pins 4/5/6 - Aux Relay 1

3 P6 Pins 6/5/4 - Strike (lock) Relay 2

4 P6 Pins 3/2/1 - Aux Relay 2

CAUTION: Some magnetic locks exhibit both high in-rush current when activated and a

high instantaneous break voltage when de-energized due to magnetic field collapse. Use a

snubber circuit across the controlling relay terminals to protect the controlling relay

contacts. Go to support.hidglobal.com, see Solution 891 - How do I wire a High In-Rush

Current locking device to VertX/Edge/Edge Solo?

VertX EVO V2000 Installation Guide, 72000-901, Rev. A.5

July 2016 Page 9 of 22

Input Connections:Input connections are analog inputs used for a combination of specific

functions such as Request-to-Exit (REX), Door monitor, etc. They can also be used as general

purpose monitoring. Connect one side of the switch or contact to the +(plus) lead and the

other to the –(minus) lead. The following table shows where the inputs are located.

Pin numbers shown on the cover use the convention +/–.

The default REX input configuration is Normally Open (NO) unsupervised (no EOL resistors).

Note: The default door switch (DS) configuration is Normally Closed (NC), unsupervised (no

EOL resistors). For UL1076 installations, all inputs must be supervised.

All other input points are defaulted for NO switches and are unsupervised (no EOL resistors).

Any input can be configured as NO or NC, as well as unsupervised or supervised. They can

be configured for supervisory resistors of 1K – 6K Ohm. The setup of supervised inputs

should be done during configuration of the VertX EVO devices through the host.

Example: Input 1, V2000 is: P2 Pin 1 is + (plus) and Pin 2 is – (minus):

Except for the door monitor, all other inputs default to NO, unsupervised:

Supervised inputs can be configured for:

Input Number V2000

1 P2 Pins 1/2 - Door Monitor

2 P2 Pins 3/4 - REX input

3 P5 Pins 4/3 - Door Monitor

4 P5 Pins 2/1 - Rex Input

5 P7 Pins 8/7 - Tamper

6 P7 Pins 6/5 - AC Fail

7 P7 Pins 4/3 - Batt Fail

Page 10 of 22 July 2016

VertX EVO V2000 Installation Guide, 72000-901, Rev. A.5

4Contact

Contact the VertX controller through the following methods.

•Discovery GUI (DHCP or Static TCP/IP Configurations Only)

•Virtual Port

4.1 HID Discovery Application (for DHCP Networks)

The HID Discovery Application provides a technician with a method of locating all of the

VertX controllers that are connected to a network. Controller information is displayed

providing the ability to ‘blink’ the VertX controller Comm LED and configure the unit by

launching a browser pointed at the Configuration GUI of the targeted controller. When the

HID Discovery Application is launched, a discover command is issued and the Configuration

GUI screen is populated with the results. Also provided is the ability to refresh the

Configuration GUI screen on command.

Use this feature when the VertX controllers and network have been installed and are

operational, but before the VertX controller(s) are configured. At this point, all of the

controllers on a network will have the same host name and unknown IP addresses (assuming

a DHCP environment). In this scenario, the only mechanism available to configure a

controller is the serial debug port or by only placing one controller on the network at a time.

The HID Discovery Application provides an easy to use mechanism to configure controllers.

Note: The Controller must be connected to the network before power is applied for DHCP to

function.

With the PC connected to the same network as the Controller, double-click1.

hid-discovery.exe.

Note: If the HID Discovery Application is not on the PC download the application2.

from www.hidglobal.com/drivers. Search for “Discovery” and the DISCOVERY GUI

download window will appear.

Select the device from the list.3.

Go to Section 5: Configure.4.

Tabla de contenidos

Otros manuales de Controladores de HID

HID

HID VertX EVO V1000 Manual de usuario

HID

HID Mercury LP1501 Manual de usuario

HID

HID Signo 25B Manual de usuario

HID

HID VertX EVO Series Manual de usuario

HID

HID Vertx CS V100 Manual de usuario

HID

HID EDGE EVO EH400-K Manual de usuario

HID

HID Signo 25B Manual de usuario

HID

HID Aero X1100 Manual de usuario

HID

HID iCLASS SE RB25F Manual de usuario

HID

HID ACW2-XN Manual de usuario

HID

HID Mercury LP1502 Manual de usuario

HID

HID EDGE EVO EH400 Manual de usuario

HID

HID Mercury LP4502 Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario