Hi-Target ZTS Series Manual de usuario

Thank you for choosing ZTS-120/120R . As your handy

construction tool, it will provide you with the most efficient and

economic solutions to your job. To fully utilize the potential of

your instrument and protect your investment, you need to, as we

strongly suggest, thoroughly read this manual before starting any

operations. Should you run into any problems, Hi-Target ’ s

technical support team will be happy to assist you

All manuals and user guides at all-guides.com

all-guides.com

Contents

Contents ........................................................................................ II

1. Precautions for Safety .......................................................... - 1 -

1.1 NOTE ......................................................................... - 1 -

1.2 Definition of Indication .............................................. - 2 -

1.3 Safety Standards for Laser ( ZTS-120/120R series ) .. - 5 -

1.4 About User .................................................................. - 6 -

1.5 Exceptions from Responsibility ................................. - 6 -

2 . Preparation before M easurement .......................................... - 7 -

2.1 About Battery ............................................................. - 7 -

2.1.1 Battery Power Symbol ....................................... - 7 -

2.1.2 Replace the Battery ........................................... - 9 -

2.1.3 Recharge the Battery ......................................... - 9 -

2.2 Setting U p the I nstrument ......................................... - 10 -

2.3 Centering and Leve lling-Up ..................................... - 11 -

3. Basic Functions .................................................................. - 13 -

3 .1 Nomenclature ........................................................... - 13 -

3.2 Basic Key Operation ................................................ - 15 -

3.3 Display ..................................................................... - 16 -

3.4 Mode Diagram .......................................................... - 16 -

3.5 Power On/Off ........................................................... - 18 -

3.6 How to Input Number and Alphabet ........................ - 19 -

3.7 How to Configure ..................................................... - 20 -

4. Angle Measurement ............................................................ - 23 -

4.1 Measure a Horizontal Angle of Two Points .............. - 23 -

4.2 Set the Horizontal Angle to a Required

Value

.......... - 23 -

All manuals and user guides at all-guides.com

III

5. Distance Measurement ....................................................... - 24 -

6. Coordinate Measurement ................................................... - 26 -

6.1 Input the Occupied Point Data ................................. - 27 -

6.2 Azimuth Setting ........................................................ - 29 -

6.3 3D Coordinate Measurement ................................. - 30 -

7. Stake out Measurement ...................................................... - 32 -

7.1 Distance Setout ......................................................... - 33 -

7.2 Coordinates Setout Measurement ............................. - 34 -

8. Area .................................................................................... - 37 -

8.1 Area Calculation by Measured Data or Input Data ... - 38 -

9. Offset Measurement ........................................................... - 40 -

9.1 Distance Offset Measurement .................................. - 41 -

9.2 Angle Offset Measurement ....................................... - 44 -

9.3 Plane Offset Measurement ....................................... - 46 -

9.4 Column Offset Measurement ................................... - 48 -

10. MLM ................................................................................ - 50 -

11. Height measurement (REM) ............................................. - 53 -

12. Intersection ....................................................................... - 56 -

12.1 Coordinates Intersection ......................................... - 57 -

12.2 Elevation Intersection — Coord.Z ........................... - 59 -

12.3 Precautions When Performing Intersection ............ - 61 -

13. Point Projection ................................................................ - 62 -

13.1 Define Baseline ...................................................... - 63 -

1 4. Inverse .............................................................................. - 64 -

15. Roadway ........................................................................... - 65 -

15.1 Define the Horizontal Curve of Roadway .............. - 67 -

15.2 Defining the Vertical Curve of Roadway ............... - 70 -

15.3 Roadway setout ...................................................... - 71 -

All manuals and user guides at all-guides.com

16. Fileman ............................................................................. - 74 -

16.1 File management .................................................... - 74 -

16.2 Parameters calibration menu .................................. - 78 -

16.2.1 calibration Index difference ........................... - 78 -

16.2.2 calibration of compensating error .................. - 79 -

16.2 .3 calibration of instrument additive constant and

multiplying constant ..................................... - 80 -

16.3 Grid factor .............................................................. - 81 -

1 7. Checkout and calibration .................................................. - 82 -

17.1 Level tube ............................................................... - 82 -

17.2 Circular level .......................................................... - 83 -

17.3 Telescope reticle ..................................................... - 83 -

17.4 The verticality of collimation axis and horizontal axis

(2 C) ........................................................................ - 85 -

17.5 Vertical plate index zero automatic compensation . - 86 -

17.6 Vertical collimation error (I Angle) and vertical

collimation zero value setting ................................. - 87 -

17.7 Plummet ................................................................. - 88 -

17.8 Instrument additive constant (K) ............................ - 90 -

17.9The parallelism of collimation axis and photoelectricity

axis ......................................................................... - 91 -

17.10 No prism ranging .................................................. - 92 -

18 . Specifications ................................................................... - 93 -

19 . Prompt ，Warning and Error Messages ............................ - 96 -

20. Standard Warranty Terms ............................................... - 100 -

All manuals and user guides at all-guides.com

- 1 -

1. Precautions

Precautions

Precautions for

for

for Safety

Safety

1.1

1.1 NOTE

NOTE

◆Do

Do not

not

not look

look

look directly

directly

directly into

into

into the

the

the sun

sun

sun with

with

with instrument

instrument

Avoid exposing to direct sunlight. Do not look into the sun

directly to protect your eyes and instrument.

◆Avoid

Avoid

Avoid exposing

exposing

exposing the

the

the instrument

instrument

instrument to

to vibrations

vibrations

When transporting, keep the instrument in the case and try your

best to avoid unnecessary vibrations.

◆Carry

Carry

Carry the

the

the instrument

instrument

When carrying the instrument handle must be held tight.

◆Check

Check

Check the

the

the battery

battery

battery power

power

Before using it, you should ensure the battery is fully charged.

◆Take

Take

Take out

out

out the

the

the battery

battery

It is not suggested to take out the battery when the instrument is

on . O therwise, the stored data may be lost. Be sure to power off

the instrument before removing battery.

◆Set

Set

Set up

up the

the

the instrument

instrument

instrument on

on the

the

the tripod

tripod

When using it please insure the connection between tripod and

instrument is firm. It is better to work with wooden tripod for

the measurement accuracy.

◆Assemble

Assemble

Assemble the

the

the tribrach

tribrach

tribrach on

on the

the

the instrument

instrument

The setting of tribrach would influence the accuracy. The

tribrach should be check frequently, the screw which connects

the tribrach and alidade must be locked tightly. And the central

fixing screw should be tight.

All manuals and user guides at all-guides.com

- 2 -

◆High

High

High temperature

temperature

temperature condition

condition

Don ’ t put the instrument in high temperature conditions

(50C/122F and up) for a long time, it is bad for the instruments

performance.

◆Temperature

Temperature

Temperature changing

changing

changing sharply

sharply

The sharp temperature changing on the instrument or prism will

shorten the distance measurement range, for example, after

taking the instrument out from a warm car to a cold condition,

wait for some time, it can be used when it adapts the

surrounding condition.

◆The

The

The noise

noise

noise from

from

from the

the

the instrument

instrument

When the instrument is in work mode, it is normal to hear noise

from the motor.

◆Stored

Stored

Stored data

data

data responsibility

responsibility

ZTS-120/120R should not be held liable for the lost data

because of wrong operation.

1.2

1.2 Definition

Definition

Definition of

of Indication

Indication

For the safety of your product and prevention of injury to

operators and other .

Persons as well as prevention of property damage, be sure to

read this manual.

The definitions of the indication are listed below. Be sure you

understand them before reading the manual ’ s main text.

All manuals and user guides at all-guides.com

all-guides.com

- 3 -

● Do not disassemble. Fire, electrical shock or burns can occur.

Only ZTS-120/120R authorized distributors can disassemble

or rebuilt.

● Do not look directly into the sun. Eye injury or blindness can

occur.

● Do not cover the charger. Fire can occur.

● Do not use power cable, socket or plug. Fire or electric shock

can result.

● Do not get battery wet. Fire or electric shock can result.

● Do not expose the instrument to burning gas or liquid and do

not use the instrument in coal mine. Blast could be result.

● Do not put the battery in the fire or high temperature condition.

Explosion, damage could result.

● Do not use the battery which is not specified by

ZTS-120/120R . Fire, electric shock or burn could result.

● Do not use the power cable which is not specified by

ZTS-120/120R . Fire could result.

WARNING

CAUTION :

！WARNING

！

Ignoring this indication and making an

operation error could possibly result in

death or serious injury to the operator.

Ignoring this indication and making an

operation error could possibly result in

personal injury or property damage.

All manuals and user guides at all-guides.com

- 4 -

● Do not short circuit of the battery. Fire could result.

● When this product encounters disturbance of severe

Electrostatic Discharge, perhaps it will have some

degradation of performance like switching on/off

automatically and so on.

● Do not touch the instrument with wet hand. Electric shock

could result.

● Do not stand or seat on the carrying case, and do not turn over

the carrying case arbitrarily, the i nstrument could be

damaged.

● Be careful of the tripod feet when setup or move it.

● Do not drop the instrument or the carry ing case, and do not

use defective belt, agraffe or hinge. Instrument damage could

result.

● Do not touch liquid leaking from the instrument or battery.

Harmful chemicals could cause burn or blisters.

● Please assemble the tribrach carefully. If the tribrach is not

stable, serious damage could result.

● Do not drop the instrument or tripod, series damage could

result. B efore us ing it, check the central screw is tigh t.

！CAUTION

All manuals and user guides at all-guides.com

- 5 -

1.3

1.3 Safety

Safety

Safety Standards

Standards

Standards for

for

for Laser

Laser

Laser (

(

( ZTS-120/120R

ZTS-120/120R

ZTS-120/120R series

series

series )

)

The ZTS-120/120R total station abides by the class of Laser

Product according to IEC Standard Publication 60825-1 Amd.

2:2001. According this standard, EDM device is classified as

Class 3R Laser Product when reflectless measurement is

selected, when the prism and reflective sheet is selected as target,

the output is equivalent to the safer class 1. Follow the safety

instructions on the labels to ensure safe use.

CAUTION: CLASS 3R LASER RADIATION WHEN

OPENAVOID DIRECT EYE EXPOSURE.

CAUTION: CLASS 2 LASER RADIATION WHEN OPENDO

NOT STARE INTO THE BEAM

Laser emit

All manuals and user guides at all-guides.com

- 6 -

Note

Note for

for

for Safety

Safety

● Never point the laser beam at othes eyes, it could cause

serious injury.

● Never look directly into the laser beam source, it could

cause permanent eye damage.

● Never stare at the laser beam, it could cause permanent eye

damage.

● Never look at the laser beam through a telescope or other

optical devices, it could cause permanent eye damage.

1.4

1.4 About

About

About User

User

1. This product is for professional use only!

The user is required to be a qualified surveyor or have a good

knowledge of surveying, in order to understand the user manual

and safety instructions, before operating, inspecting or adjusting.

2. Wear required protectors (safety shoes, helmet, etc.) when

operating.

1.5

1.5 Exceptions

Exceptions

Exceptions from

from

from Responsibility

Responsibility

1. The user of this product is expected to follow all operating

instructions and makeperiodic checks of the product ’ s

performance.

2. The manufacturer assumes no responsibility for results of a

WARNING

All manuals and user guides at all-guides.com

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Hi-Target

Hi-Target

Hi-Target ZTS-120 Manual de usuario

Hi-Target

Hi-Target ZTS-320R Series Manual de usuario

Hi-Target

Hi-Target ZTS-320 Series Manual de usuario

Hi-Target

Hi-Target V200 Manual de usuario

Hi-Target

Hi-Target ZTS-720 Series Manual de usuario

Hi-Target

Hi-Target HTS-420R Manual de usuario

Hi-Target

Hi-Target V90 Plus Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario