Hewlett Packard Enterprise Altoline 6921 Instrucciones de montaje

MF877-00 Page 1

Template Revision A

HPE instructions for this template are available at MF877-01

Product End-of-Life Disassembly Instructions

Product Category: Networking Equipment

Marketing Name / Model

[List multiple models if applicable.]

HPE Altoline 6921 48XGT 6QSFP+ x86 ONIE AC Front-to-Back Switch (JL315A)

HPE Altoline 6921 48XGT 6QSFP+ x86 ONIE AC Back-to-Front Switch (JL316A)

Purpose: The document is intended for use by end-of-life recyclers or treatment facilities. It provides the basic instructions

for the disassembly of HPE products to remove components and materials requiring selective treatment, as defined by EU

directive 2002/96/EC, Waste Electrical and Electronic Equipment (WEEE).

1.0 Items Requiring Selective Treatment

1.1 Items listed below are classified as requiring selective treatment.

1.2 Enter the quantity of items contained within the product which require selective treatment in the right column, as

applicable.

Item Description Notes

Quantity

of items

included

in product

Printed Circuit Boards (PCB) or Printed Circuit

Assemblies (PCA)

With a surface greater than 10 sq cm

Batteries

All types including standard alkaline and lithium

coin or button style batteries

Mercury-containing components

For example, mercury in lamps, display backlights,

scanner lamps, switches, batteries

Liquid Crystal Displays (LCD) with a surface

greater than 100 sq cm

Includes background illuminated displays with gas

discharge lamps

Cathode Ray Tubes (CRT)

Capacitors / condensers (Containing PCB/PCT)

Electrolytic Capacitors / Condensers measuring

greater than 2.5 cm in diameter or height

External electrical cables and cords

Gas Discharge Lamps

Plastics containing Brominated Flame Retardants

weighing > 25 grams (not including PCBs or PCAs

already listed as a separate item above)

Components and parts containing toner and ink,

including liquids, semi-liquids (gel/paste) and toner

Include the cartridges, print heads, tubes, vent

chambers, and service stations.

Components and waste containing asbestos

Components, parts and materials containing

refractory ceramic fibers

MF877-00 Page 2

Template Revision A

HPE instructions for this template are available at MF877-01

Item Description Notes

Quantity

of items

included

in product

Components, parts and materials containing

radioactive substances

2.0 Tools Required

List the type and size of the tools that would typically be used to disassemble the product to a point where components

and materials requiring selective treatment can be removed.

Tool Description

Tool Size (if

applicable)

Phillips screwdriver

various sizes

Small adjustable wrench

Needle nose pliers

3.0 Product Disassembly Process

3.1 List the basic steps that should typically be followed to remove components and materials requiring selective treatment:

1. Remove the chassis lid

1. Using a Phillips screwdriver, remove the screws (qty 20)

2. Slide the lid off the chassis

2. Remove the two power supplies

1. Locate the power supplies at either side of the back of the chassis

2. While pressing the release lever toward the handle, pull the power supply out of the chassis

3. Repeat for the other power supply

3. Remove the five fan assemblies from the back of the chassis

1. Locate the fan assemblies in the middle of the back of the chassis

2. Either by hand or using a Phillips screwdriver, loosen the set screw for each fan assembly

3. Using the fan assembly handle, pull out a fan assembly

4. Repeat for the remaining four fan assemblies

4. Remove the center PCA assembly

1. Using a Phillips screwdriver, remove the two screws at the back corners of the center PCA assembly

2. Using a small adjustable wrench, remove the two nuts at the front corners of the center PCA assembly

3. Slowly remove the center PCA assembly from the chassis, taking into account the connector under the bottom

left corner

5. Remove the two DIMMs from the center PCA assembly

1. Gently spread the retaining levers away from the top DIMM

2. Remove the top DIMM

3. Repeat for the bottom DIMM

6. Remove the heatsink from the center PCA assembly

1. Locate the heatsink fasteners on the underside of the PCA, opposite the heatsink

2. Use needle nose pliers to pinch the heat sink fasteners while removing the heat sinks from the center PCA

assembly

7. Remove the fan assembly PCA

1. Disconnect the ribbon connector and the cable connector next to it from the fan assembly PCA

2. Using a Phillips screwdriver, remove the four screws attaching the fan assembly PCA to the chassis

3. Remove the fan assembly PCA from the chassis

8. Remove the main PCA

1. Disconnect the ribbon connector and the cable connector that were attached to the fan assembly PCA

2. Using a Phillips screwdriver, remove the two screws securing the small sheet metal air flow diverter to the

middle of the main PCA

MF877-00 Page 3

Template Revision A

HPE instructions for this template are available at MF877-01

3. Remove the small sheet metal air flow diverter

4. Using a Phillips screwdriver, remove the two screws securing the double bend sheet metal air flow diverter to

the left side of the main PCA

5. Remove the double bend sheet metal air flow diverter

6. Using a small adjustable wrench, remove the four hexagonal studs near the corners of the heat sink

7. Using a small adjustable wrench, remove the two small hexagonal studs that were supporting the front edge of

the middle PCA stack

8. Using a Phillips screwdriver, remove the two screws located on the bottom of the chassis securing a close out

plate

9. Remove the close out plate

10. Using a Phillips screwdriver, remove the screws securing the two power supply connectors (two screws each)

11. Repeat for the other power supply connector

12. Using a Phillips screwdriver, remove the nine screws holding down the main PCA

13. Remove the main PCA from the chassis

9. Using a Phillips screwdriver, loosen the screws securing the three heat sinks (four screws each) to the main PCA

10. Remove the heat sinks and their backing hardware from the main PCA

3.2 Optional Graphic. If the disassembly process is complex, insert a graphic illustration below to identify the items

contained in the product that require selective treatment (with descriptions and arrows identifying locations).

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Hewlett Packard Enterprise

Hewlett Packard Enterprise

Hewlett Packard Enterprise Edgeline EL4000 Manual de usuario

Hewlett Packard Enterprise

Hewlett Packard Enterprise Aruba 8360-32Y4C Instrucciones de montaje

Hewlett Packard Enterprise

Hewlett Packard Enterprise StorageWorks 8/8 Base SAN Switch Manual de usuario

Hewlett Packard Enterprise

Hewlett Packard Enterprise OfficeConnect 1850 Series Manual de usuario

Hewlett Packard Enterprise

Hewlett Packard Enterprise HPE OfficeConnect 1405 v3 Switch Series Manual de usuario

Hewlett Packard Enterprise

Hewlett Packard Enterprise Aruba 8360 Series Manual de usuario

Hewlett Packard Enterprise

Hewlett Packard Enterprise Aruba 3810 Manual de usuario

Hewlett Packard Enterprise

Hewlett Packard Enterprise 2930M Series Manual de usuario

Hewlett Packard Enterprise

Hewlett Packard Enterprise Aruba 2530 Manual de programación

Hewlett Packard Enterprise

Hewlett Packard Enterprise Aruba 6200F Manual de usuario

Hewlett Packard Enterprise

Hewlett Packard Enterprise SN2100M Manual de usuario

Hewlett Packard Enterprise

Hewlett Packard Enterprise M-Series Manual de usuario

Hewlett Packard Enterprise

Hewlett Packard Enterprise Brocade 32Gb/12 2SFP+ Manual de usuario

Hewlett Packard Enterprise

Hewlett Packard Enterprise Aruba 2920 Manual de usuario

Hewlett Packard Enterprise

Hewlett Packard Enterprise B Series Manual de programación

Hewlett Packard Enterprise

Hewlett Packard Enterprise Aruba Instant On 1960 24G 20p Class4 4p Class6 PoE 2XGT 2SFP+ 370W... Instrucciones de montaje

Hewlett Packard Enterprise

Hewlett Packard Enterprise JL354A Manual de usuario

Hewlett Packard Enterprise

Hewlett Packard Enterprise FlexFabric 5940 Series Manual de usuario

Hewlett Packard Enterprise

Hewlett Packard Enterprise 5920 Series Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario