Henko 671 Manual de usuario

Operating Manual

Henko 671 Brush Machine

Henko A&T B.V.

Graafschap Hornelaan 184, 6004 HT Weert,

The Netherlands

Tel: +31 (0)495 63 30 10, Fax: +31 (0)495 58 67 35

[email protected], www.henko-at.nl

Rev. 18-8-2014

Page 2 of 33 18-8-2014 Henko A&T B.V.

Introduction

Dear reader,

This operating manual provides all information for

safe operation of the Henko 671 Brush Machine.

The Henko 671 Brush Machine has been designed and built in

accordance with the state of the art and recognised safety rules

and regulations. Nevertheless dangers for personnel or objects

can occur, because not all danger zones can be avoided if the

functionality is to remain intact. However you can prevent

accidents due to these dangers by complying with the

instructions in this operating manual. Moreover you will then be

able to use the Brush Machine to its full capacity and avoid

unnecessary disturbances.

CAUTION!

There is danger of injury and danger of material damage

when assembling, operating, and maintaining the Brush

Machine. Therefore:



First read this operating manual carefully, prior to assembly

and operation of the Brush Machine. Always comply with the

instructions and information contained herein, particularly the

safety instructions.

If the operating manual is lost or in poor condition, request a

new copy from the manufacturer (the same applies for parts of

the operating manual).

This operating manual only applies for the Brush Machine

specified on the cover sheet and at the end of every page.

Compare this information with the information on the type plate

of the Brush Machine.

After you have read the entire operating manual thoroughly for

the first time, take good care of the operating manual over the

entire service life of the Brush Machine, so that you can look up

something later.

If you sell the Brush Machine, give this operating manual to

the new owner.

All information, illustrations and dimensions in this operating

manual are non-binding. No claims whatsoever can be derived

from this information, illustrations or dimensions.

Introduction

Henko A&T B.V. 18-8-2014 Page 3 of 33

Reprinting or duplication of any type, including excerpts,

requires the written permission of the manufacturer.

Conversion of, or changes to the Brush Machine are only

permitted with the manufacturer's written consent.

Unauthorised conversion voids any liability on the part of the

manufacturer, as well as the guarantee.

Only use original spare parts and accessories that are

approved by the manufacturer. Otherwise the design-specified

characteristics of the Brush Machine, the functionality or the

safety can be impaired. Consequently the use of other parts

voids the liability for the ensuing consequences.

Contact your specialist dealer to order spare parts or

accessories.

In addition comply with the instructions in the operating manual

of the motor manufacturer. This is included in the sub-package

for the Brush Machine.

Henko A&T B.V. assumes no liability for the content of the

operating manual provided by the motor manufacturer.

Explanation of symbols, signs and direction indications

For better understanding, the following conventions are used for

this operating manual:

To emphasise important information, the following types of

special notices are used:

DANGER!

There is an imminent dangerous situation that results in death

or serious injury if it is not avoided.

WARNING!

There is a possible dangerous situation that can result in death

or serious injury if it is not avoided.

Introduction

Page 4 of 33 18-8-2014 Henko A&T B.V.

CAUTION!



There is a possible dangerous situation that can result in

minor injury or material damage, if it is not avoided.

ATTENTION!

...indicates a possible dangerous situation that can result in

material damage, if it is not avoided.

NOTE

...indicates useful tips and recommendations, as well as

information for efficient and trouble-free operation.

...refers to important information in other sections and documents.

Many texts serve a particular purpose. These texts are marked

as follows:

Listings.

Instructing text, e. g. a sequence of activities.

In the text the sides of the Brush Machine are cited (left, right,

front, rear). Left or right refers to the side that the operator of

the machine sees viewed from the direction of travel. The Brush

Machine of the machine is mounted in front, the steering arm is

mounted in the rear.

Introduction

Henko A&T B.V. 18-8-2014 Page 5 of 33

Table of contents

Introduction . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . 2

Table of contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

1.1 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

1.2 Non-intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

1.3 Product observation . . . . . . . . . . . . . . . . . . . . . . . . . . 8

1.4 Requirement imposed on the operator or personnel . 9

1.5 Danger zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

1.6 Work clothing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

1.7 Safety devices and protective devices . . . . . . . . . . . 11

1.7.1 Safety switch . . . . . . . . . . . . . . . . . . . . . . . . . 11

1.7.2 Brush Machine deck . . . . . . . . . . . . . . . . . . 11

1.7.3 Protective cover . . . . . . . . . . . . . . . . . . . . . . . 11

1.8 Safety regulations and accident

prevention regulations . . . . . . . . . . . . . . . . . . . . . . . 12

1.9 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

1.10 Safety signs on the Brush Machine . . . . . . . . . 14

2 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

2.1Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

2.2Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

3 Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

3.1 Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

3.2 Making the steering arm operational . . . . . . . . . . . . 19

4 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

4.1 Preparatory activities . . . . . . . . . . . . . . . . . . . . . . . . 23

4.1.1 Adjusting the height of the Brush Machine . . 24

4.1.2 Checking the motor oil level . . . . . . . . . . . . . . 24

4.1.3 Filling fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Table of contents

Page 6 of 33 18-8-2014 Henko A&T B.V.

4.2 Sweep operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

4.2.1 Starting the motor . . . . . . . . . . . . . . . . . . . . . . 25

4.2.2 Stopping the motor . . . . . . . . . . . . . . . . . . . . . 26

4.2.3 Switching the traction drive on and off . . . . . . 26

4.2.4 Switching the Brush Machine drive

on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

4.2.5 Side adjustment of the Brush Machine . . . . . 27

5 Maintenance and repair . . . . . . . . . . . . . . . . . . . . . . . . . . 28

5.1 Safety guidelines for maintenance and repair . . . . . 28

5.2 Regular maintenance tasks . . . . . . . . . . . . . . . . . . . 29

5.2.1 Maintenance schedule . . . . . . . . . . . . . . . . . . 29

5.2.2 Maintenance records . . . . . . . . . . . . . . . . . . . .30

5.2.3 Checking the Bowden cables

for ease of movement . . . . . . . . . . . . . . . . . . . 30

5.2.4 Checking the air pressure in the tyres . . . . . . .31

5.2.5 Cleaning the Brush Machine . . . . . . . . . . 31

5.2.6 Checking and cleaning the air filter . . . . . . . . . 31

5.3 Maintenance and repair verifications . . . . . . . . . . . . 32

6 Decommissioning and preservation . . . . . . . . . . . . . . . 33

7 Faults and fault correction . . . . . . . . . . . . . . . . . . . . . . . . 33

Table of contents

Henko A&T B.V. 18-8-2014 Page 7 of 33

1 Safety

The basic prerequisite for safe and trouble-free operation of the

Brush Machine is knowledge of the safety instructions and

safety regulations.

Consequently read this chapter carefully all the way through

and comply with the specified instructions and warnings.

The safety instructions and warnings that you find at the

appropriate point in the text of the following chapters must be

complied with. The manufacturer cannot be made liable if the

instructions and warnings are not complied with.

In addition to the instructions contained in this operating

manual, the statutory regulations, particularly the safety and

accident prevention regulations, must also be complied with.

1.1 Intended use

The Henko 671 Brush Machine may only be used to brush

artificial grass, clean paths and surfaces that are paved with

concrete, asphalt, paving stones or slabs outside of closed

rooms.

Intended use also includes compliance with all the instructions

in the operating manual.

DANGER!

If the Brush Machine is used for a use other than the use

described above, dangerous situations can occur for people or

material damage can occur.

Therefore:



Only use the Brush Machine for its intended purpose.

Always comply with all the instructions in this operating

manual.

Particularly refrain from the uses of the sweeping machine

listed in section 1.2. They are considered non-intended use.

Safety

Page 8 of 33 18-8-2014 Henko A&T B.V.

1.2 Non-intended use

Any use that deviates from that described in section 1.1, is

considered non-intended use.

For example, non-intended use of the Brush Machine

occurs when

it is used to clean unpaved surfaces e.g. gravel paths,

it is used to clean roofs or flat roofs,

it is used in enclosed spaces, e.g. halls, or barns,

it is used to transport persons or objects,

it is used to move or carry objects or vehicles,

it is operated in faulty condition or with safety-relevant

faults,

it is used without the safety cladding elements that are

installed as standard equipment,

unsuitable personnel are assigned to operate the sweeping

machine.

1.3 Product observation

Notify us without delay if faults or problems occur when

operating your Brush Machine, or if accidents occur or nearly

occur.

Together with you we will find a solution to the problem and

allow the knowledge gained to flow into our subsequent work.

Safety

Henko A&T B.V. 18-8-2014 Page 9 of 33

1.4 Requirements imposed on the operator

or personnel

Handling the Brush Machine is only permitted for persons,

who are at least 16 years old,

who are physically and mentally suited to do so,

who have read and understood this operating manual, and

from whom it is expected that they responsibly perform the

tasks assigned to them.

Commissioning, maintenance, repair and disposal of the Brush

Machine may only be executed by the specialist dealer or by

persons with appropriate technical training and experience.

1.5 Danger zone

The danger zone is the area in which the safety or the health of

persons is jeopardised. Consequently no one should be in this

area when the Brush Machine is in operation.

WARNING!

For persons in the danger zone there is danger of injury due to

collision with the Brush Machine and due to thrown up

sweepings.

Therefore:



Only operate the Brush Machine if no one is in the danger

zone.

Carefully observe the danger zone and stop the sweeping

machine if persons enter the danger zone.

The danger zone is shown in the sketch (see Fig. 1, on the next

page):

A top view of the Brush Machine is shown. The shaded area is

the danger zone.

The danger zone on the right side and left side is determined

through the width of the Brush Machine. Toward the front side

of the Brush Machine the length of the danger zone is 5 m in

front of the Brush Machine.

Safety

Page 10 of 33 18-8-2014 Henko A&T B.V.

NOTE

When swinging the Brush Machine to the right or left this change in

direction also applies for the danger zone.

Safety

Fig. 1:

Danger zone

2.5 m

5 m ahead of the Brush Machine

Tabla de contenidos

Manuales populares de Equipos para césped y jardín de otras marcas

Vertex

Vertex 1/3 HP Especificaciones técnicas

GHE

GHE AeroFlo 80 Manual de usuario

Millcreek

Millcreek 406 Manual de usuario

Land Pride

Land Pride Post Hole Diggers HD25 Manual de usuario

extraspace

extraspace GardenStore Manual de usuario

Yazoo/Kees

Yazoo/Kees Z9 Commercial Collection System Z9A Manual de programación

Premier designs

Premier designs WindGarden 26829 Manual de usuario

Snapper

Snapper 1691351 Manual de usuario

Mosquito Magnet

Mosquito Magnet Patriot Manual de usuario

Perfect

Perfect BG2 Manual de usuario

P.Lindberg

P.Lindberg LS2 Manual de usuario

Gardena

Gardena Easy 1887 Manual de usuario

Makita

Makita UM104D Manual de usuario

AQUA FLOW

AQUA FLOW PNRAD Manual de usuario

Tru-Turf

Tru-Turf RB48-11A Golf Green Roller Guía del usuario

BIOGROD

BIOGROD 730710 Manual de usuario

Land Pride

Land Pride RCF2784 Manual de usuario

Makita

Makita UM110D Manual de usuario