Hema Navigator Manual de instrucciones
2
H E M A N AV I G AT O R
QUIC K USE R G U I D E
POWERED BY
Getting Started
2
What is in the box?
- HEMA NAVIGATOR GPS unit
- Suction windscreen mount
- 12V car charger
- 240V AC charger
- USB cable
- Quick User Manual
- SD Card
serial #: HNV11008050001
Speaker
RESET
Reset button
(push lightly with pen)
External GPS
Aerial Port
Stylus pen
4.3” 16:9 Touch LCD Screen
Indicator lights
Red = Charging
Green = Battery full
Orange = no GPS lock
SD card slot
3.5 mm Headphone
Jack
Power & Mini
USB connector
Power
press for 2 sec to
turn on/off
Top cradle
mount slot
Exit Navigation
Step 1: Mount the GPS
Select a suitable location to mount the GPS on your windscreen.
Clean & dry the suction cup and windscreen.
Plug the Car Charger into the right side of the GPS.
Attach the cradle to the suction windscreen mount.
Adjust the angle with the rotary clamp if necessary.
Place the suction cup on the windscreen and flip the back lever
towards the windscreen.
Press the bottom of the GPS on to the cradle and gently ‘snap’ the top
of the GPS into the cradle.
Plug the car charger into a power outlet in your vehicle. Your unit
should turn on automatically if it is plugged in and your vehicle key is
turned to ON/ACC.
Ways to charge the GPS
Connect the 12V car charger to the GPS and to a power outlet in your
vehicle.
Connect the AC adaptor to the GPS and a 240V AC wall outlet.
Connect the USB cable to the GPS and charge it from a PC.
Turn on your GPS, press the button for 2 sec
Turn off your GPS, press the button for 2 sec
1.
2.
3.
4.
5.
6.
-
-
-
Step 2: Turning on your GPS
Step 3: System Menu Options
Battery Status
Touch To Start
Street Navigation
Touch to Start 4WD and
Topographical GPS
Main Menu: Tools & Settings
To Start Street Navigation
Acquiring Satellites
Before the HEMA Navigator can find your location and navigate a route,
it requires GPS satellite lock.
1. Go outdoors to an open area, GPS position detected
away from tall buildings & trees.
2.Turn on the HEMA Navigator and
start Street Navigation. Acquiring
GPS lock may take a few minutes.
Acquiring GPS lock screen Position shown on map
No GPS lock
When a valid GPS position is
established, the unit will automatically
zoom to street level.Your GPS
position is indicated by a red dot.
No GPS detected
Your GPS position cannot be
detected. If indoors, GPS signal may
not be detected.
If GPS position cannot be detected
after 10 mins, reset your device &
try again.
Touch to start Street Navigation
What's on the map screen?
Main
Menu
Zoom
Out
Zoom
In
Next Turn Road Name
Map
Current Road Name Battery
Status GPS
Signal
Strength
Compass
(Red points North)
Next
Turn
Turn
After
Next
Speed
Remaining
Distance
Remaining
Time
ETA
Distance to
next turn
Press to change
keyboard layout
Finding an address
1. Touch to enter the MAIN MENU > touch NAVIGATE TO >
LOCATIONS > a keyboard will appear for address input.
2.To input an address, simply enter
HOUSE NUMBER (Space) first 4 letters of the STREET NAME (Space) first 4
letters of the SUBURB, then hit
E.G. for 217 Flinders St Melbourne, type in 217 FLIN MELB
KEYBOARD: (QWERTY layout) To search the data base simply
enter
The House Number > first 4
letters of the street name >
first 4 letters of the suburb name.
Navigating to a destination
A list of available locations will
appear. Select the most appropriate
location and touch to start
navigation.
There may be too many
locations to choose from.To refine
a search, go to the previous screen
and enter more characters to either
street name or suburb.
If you do not have the HOUSE NUMBER or STREET NAME or SUBURB? Don’t
worry, just type in the information you have. QuickSearch will identify the
closest match in it’s database and display a number of locations you can
choose from.
for Flinders St Melbourne, type in FLIN MELB
for Melbourne, type in MELB
for Flinders St, type in FLIN
for 217 Flinders St, type in 217 FLIN
NOTE: Do not input the road type such as St, Street or Rd, Road. etc
Need more help?
There are a host of other software features not covered by this quick user
manual
For further assistance on your street navigation, go to the MAIN MENU >
Scroll down > HELP.There you will find help topics.
www.hemanavigator.com.au
For further assistance, please visit
CLICK ON SUPPORT
To Start OziExplorer
Acquiring Satellites
Before the HEMA Navigator can find your location, it requires GPS satellite lock.
Red = No GPS lock, Green = GPS lock
Touch to start OziExplorer
To open a map, either select on the Main Tool bar, FILE > OPEN MAP FILE. Or
click the OPEN MAP ICON.
1. Go outdoors to an open area, away
from tall buildings & trees.
2.Turn on the HEMA Navigator and
start OziExplorer. Acquiring GPS lock
may take a few minutes.
3. Press or to scroll through
various screen views.
Select the desired map file and press OK button
map files
Folders Scroll
Up/Down
OK button
Open A Map
Waypoints
What is a waypoint?
A waypoint is a user created position on a map.Waypoints can be used for
a wide range of things from marking points of interest to camp sites, to
fishing hotspots on rivers and lakes, landmarks etc, that you may wish to
return to. You can save waypoints and swap them with your friends.
Using the Waypoint Toolbar
The Waypoint Toolbar can be accessed by selecting VIEW > TOOLBARS >
WAYPOINT TOOLBAR.
Add a Waypoint - If selected, a waypoint is added at the position on the
map where you touch.
Delete Waypoints - All waypoints are deleted from the map.
Display Waypoint List - A list of waypoints on the map is displayed.The
list shows information about each waypoint.
Load a Waypoint File - Select a waypoint file (.wpt) to load onto the map.
Save Waypoints to File - All waypoints currently on the map are saved to
a waypoint file (.wpt).
Show/Hide Waypoint Name - Waypoint names are displayed on map /
or not.
Auto Show Waypoint Properties - If selected, the waypoint properties
dialog is shown automatically when a new waypoint is added. Changes
to the name and description of the waypoint can be made.
Close - Turns off waypoint toolbar.
By default, Proximity warning to Waypoints is activated. Alarm is triggered
when you come within a certain distance of the waypoint.These can be
used to inform of arrival at locations or to warn of sharp drops or inclines.
Proximity Warning
Route
Routes are a series of waypoints linked together.
Using the Route Create Toolbar
The Rout Create Toolbar can be accessed by selecting VIEW > TOOLBARS >
ROUTE CREATE TOOLBAR.
Add a Route Waypoint - If selected, a Route waypoint is added at the
position on the map where you touch.
Delete Route - The current route displayed is deleted from the map.
Display the Route Properties Dialog - The properties dialog displays a
list of the route waypoints.
Load a Route - the selected route is loaded to the map.
Save Route to File - The currently loaded route is saved as a (.rt2) file.
Show/Hide Route Waypoint Name - If selected, route waypoint names
are displayed.
Close - Turns off Route Create toolbar.
Insert a Route Waypoint - If selected, a route waypoint is inserted
between two waypoints or at the start or end of the route depending
on a best choice.
How to create a Route
Bring up the Route Create Toolbar by selecting VIEW > TOOLBARS > ROUTE
CREATE. Select the Add a Route Waypoint button. Using the Stylus, insert
any number of waypoints by tapping on the screen.
When you have finished creating a route, select Save Route to File from the
Toolbar to save the created Route to file for later use.
Navigation
When a Route has been plotted on the map, it allows Voice activated navigation to each of its
waypoints.
1. Select the button on the tool bar & select Route Navigation Page.
2. Select to active the Navigation Toolbar. Select Start Route Forward button.
You will notice a Yellow/Red navigation line pointing as the crow flies to the nearest waypoint
in that route.This is a graphical indication of your relative position to that waypoint. On the
side is all the relevant information to aid in navigation.
Route Navigation Page
Current Speed Current Heading
Bearing
to WP
Distance
to WP
Distance
Remaining
in Route
Navigation Toolbar
Map Zoom Level
Zoom
In
Zoom
Out
While navigating, when a WP (waypoint) is reached, you will hear voice instruction on how to
proceed. Once the WP is passed, it will automatically proceed to the next WP in route.
Reverse Navigation.
In some circumstances, you may want to navigate from the last WP to the first WP. To do so,
select the Navigation Toolbar and select Start Route Reverse.
Stop Navigation.
To cancel navigation, select the Navigation Toolbar and select Stop Navigation.
Tabla de contenidos
Otros manuales de Sistema de navegación para automóviles de Hema
