HELSEL DRONEPANG Manual de usuario
USER MANUAL
Contents
1. CAUTION
2.COMPONENTS
3.INFORMATION &INSTRUCTIONS
01)Main Frame
02)Controller
03)Charger
04)Safety Precautions
05)Turn Controller on & off
06)IMU reset
07)Starting the Motors
08) Stopping the Motors
09) Controller modes
10) Altitude hold mode
11)Headless Mode
12)Speed Mode
13)ONE Button take off & ONE Button land
14) Reset to fly
15) Change LED Color
4. FAQ
5.Specifications & Information
03
04
05
05
06
07
09
10
10
11
11
12
12
13
13
14
14
15
15
17
F2 ST USER MANUAL
1. CAUTION
WARNING
※Inaltitude hold flight modes, strong shocks are a cause of weakening the
intrinsic function.
Repeated strong shocks can lead to rapid climbs or uncontrollable flights.
- Repeated strong shocks can lead to rapid climbs or uncontrollable flights.
- Enter free flight mode or recalibrate the IMU.
- When charging the battery, stop using the inflated battery
※ The 'Dronepang F2 ST' flight control panel is not waterproof.
※ Serious shocks can damage drone structures.
※ In altitude hold flight mode, high-intensity shocks can cause errors in altitude
hold functions, resulting in high jumps and loss of control.
※ Re-calibrate the IMU after entering drone altitude hold mode or landing the
drone.
※ The 'Dronepang F2ST' can only be used for 3S (11.1V) lithium batteries.
3
※ Do not place your hands inside the shell until the propeller has stopped
completely.
※ Don't fly towards people and animals when you control drones.
※ Long hair can be dangerous because it gets caught in a rotating propeller.
Wear or tie a hat during the flight.
※ When removing the mounted shell, first remove the Dronepang battery or
remove the propeller.
※ When replacing a drone battery, keep the controls safe to prevent accidental
operation by others.
※ Dronepang is designed to be suitable for indoor flight.
- The drone cannot be controlled outside the control range of the controller signal.
- Be careful not to deviate from the field of view during operation.
- Wind-affected outdoor flights are the cause of dysfunction. It's better to fly indoors.
Contents
LiPo LiFe
LiHV
BATT
TYPE
Multi Chemistry Charger
1A 2A 3A 4A
NiMH
LiPo LiFe
LiHV
Multi Chemistry Charger
1A 2A 3A 4A BATT TYPE
NiMH
STEP. 03 CHARGER [ST450]
POWER PORT
AC 100-240V
LiHVBATTERYLED
LiMHBATTERYLED
4SBALANCE PORT
LiPoBATTERYLED
LiFeBATTERYLED
CHARGING A
SELECTOR SWITCH
PRODUCT INFORMATION
Select the type of battery you want to charge
7
The AC power cord can be used to connect directly to the AC outlet (100-240V).
It is a ST450 100-240V AC balance charger used in Dronepang F2ST. It can charge 2-4
cell LiPo, LiFe, and LiHV batteries in balance mode. It can charge up to 4A with a 500W
power supply, and the user can easily select and charge depending on the capacity of
the battery among the four A/2A/3A/4A amps.
1. Please connect the charger and power cord.
2. Plug the power cord into the wall outlet. All LEDs will flash for approximately 1 second,
and the green and red LEDs will alternately light on the battery type ready to charge.
3. Press the battery type button to set it to fit the battery you want to charge.
3SBALANCE PORT
2SBALANCE PORT
BATTERY SOCKET
BATTERY TYPE
BUTTON
PRODUCT INFORMATION
Contents
LiPo LiFe
LiHV
Multi Chemistry Charger
1A 2A 3A 4A BATT TYPE
NiMH
4. Use the left slider to set the voltage to charge.
Voltage can be set from 1A (1000mA) to 4A
(4000mA).
|CAUTION| In LiMH mode, only LiMH batteries must be charged. Charging
other
types of batteries can cause fire, injury and property damage.
The recommended charging speed is 1C. (Battery Capacity = Charging
Voltage) 1C is Total Capacity = Charging Voltage.
LiPo
8
5. Recharge LiPo/LiFe/LiHV batteries
Plug the charging cable into the front battery socket of the charger
to match the color and connect the battery. Attach the battery
balance jack to the port on the right side of the charger to align the
battery cell to be charged.
This section describes how to charge
the battery balance using the ST450
charger. If the connection is not
properly made or charging is different
from the description, the charger may
be overloaded.
| Caution |
Charging cable and battery jack
Blinking green and red alternately Ready to charge
Red LED Charge 25%
Red blinking light Charge 25%~50%
Yellow LED Charge 50%~70%
Green blinking light Charge 70%~99%
Green LED Full
When the battery is fully charged, the LED on the charger turns green.
After disassembling the battery into the charger, the LED on the charger flashes
green to allow you to charge another battery.
6. Recharge NiMH Battery
Combine the battery with the charging cable and connect it to the socket on the
front of the charger by color.
Press the "BATT TYPE" button for 2 seconds to start charging. Charges when the
LED indicator is illuminated.
When the battery is fully charged, the charge indicator remains green.
F2 ST USER MANUAL
Contents
When flying ensure that the drone is kept away from other people, trees,
electric wires, buildings, airports or signal transmitting tower etc.
Ensure that the weather conditions are suitable for flying. Do not fly the
drone during snow, rain, fog, thunder or in windy conditions.
STEP. 04
|CAUTION | Flights under unstable weather conditions should be prohibited under any
circumstances when flying outdoors. This is the most basic user instruction and
be sure to read this before flying to avoid possible accidents.
9
SAFETY FOR FLY
DO NOT touch the rotating blade
during operation. It can cause
injury or damage to property.
No-fly zone must be observed. It
is the user's responsibility to
ensure that drones operate
legally and safely.
Only fly in an open space Keep within line of sight Fly at a height below 80m
Contents
STEP. 05
CONTROLLER ON, OFF
: Press and hold the two buttons until
the power is turned on.
|CAUTION|
If the controller is switched off during flight or automatically switched off due to
lack of battery on the controller, the 'Dronepang F2 ST' may be out of control.
Use in a fully charged state to avoid running out of battery on the controller.
If the battery in Dronepang is lower than the warning voltage (low power), the
controller will emit a warning tone and the 'Dronepang F2 ST' tail light will flash.
At the end of the flight, disconnect the 'Dronefang F2 ST' battery, place all
toggle switches on top and turn off the controls.
If the power does not turn off or on, make sure that all toggle switches are
located at the top.
10
STEP. 06
CONTROLLER ON, OFF
1. After powering on the controller, connect the battery to the 'Dronepang F2 ST' and hold it
horizontally with the power on, then lower the left and right sides of the controller simultaneously
to the lower right corner for more than 3 seconds.
2. The Dronepang tail light flashes slowly.
3. When the tail light flashes, place the stick in place.
4. Hold still for a few seconds to complete the calibration without flashing the tail light.
* It is recommended that calibration be performed before every take-off.
* Do not touch the drone during calibration.
STANDBY & IMU RESET (before flight)
F2 ST USER MANUAL
Contents
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
