Heise HE-SWP8 Manual de usuario

Universal

8 Gang Switch Panel System

Visit HeiseLED.com for more detailed information about the product and up-to-date

vehicle specific applications.

• Control 8 auxiliary LED lights or electrical devices

• 50 label designs

• Blue LED back lighting

• 60 amp resettable circuit breaker

• On / Off switch or Momentary press operation

• Water resistant Design

• 6 spare fuses

Installation................................................2-4

Wiring............................................................5

Menu Operation.........................................6-7

Specifications................................................8

TABLE OF CONTENTS

Attention! We recommend disconnecting the

vehicle battery prior to installation.

When testing the aftermarket equipment,

ensure that all factory equipment is connected

before cycling the key to ignition.

TOOLS REQUIRED

• Wire stripper

• Cutters

• Drill

• Metric socket set

• Universal step bit

• 1/8” & 1/4” Drill bit

• #1, #2 Phillips screwdriver

• 4mm hex key (included)

Part Components

A) Switch Panel B) Control Box C) Power Harness, Connections D) 3 x Mounting Brackets E) 50 x Labels (Decals)

A C

HE-SWP8

INSTALLATION INSTRUCTIONS

#HeiseLED

Part Applications

• Universal; Automotive, Marine, Jeep®, ATV/UTV,

Golf cart etc.

Product Features

21.800.221.0932 HeiseLED.com

INSTALLATION

Mounting Control Box

• Using the mounting bracket as a guide (Figure A), find a good location to

mount the control box.*

• The ideal mounting of the box should allow for an unobstructed path for the

power wires, accessory wires, and the control harnesses.

• If you decide to drill, check the clearance behind the drilling location. Make

sure you are not going to drill through and damage any wiring harness and

components in the vehicle.

(

Figure B

)

There are two different mounting options provided within the HE-SWP8;

• Fix mount bracket. (Figure A) *

• Flush mount. (Figure B)

(

Figure A

)

*Note: Fix mount is the recommended mounting.

FIX MOUNT

• Using the control box as a guide (Figure B), find a good location to mount.**

• The ideal mounting of the box should allow for an unobstructed path for the

power wires, accessory wires, and the control harnesses.

• If you decide to drill, check the clearance behind the drilling location. Make

sure you are not going to drill through and damage any wiring harness and

components in the vehicle.

FLUSH MOUNT

Keep in mind the switch panel control wire is appropriately 9 feet long. Do not attempt to extend the control wire. Cutting and splicing may void the warranty and damage the product.

**Note: The bottom of the control box needs an unobstructed path for the wire to exit.

REV. 12/20/2019 INSTHE-SWP8

INSTALLATION

Mounting Examples

41.800.221.0932 HeiseLED.com

INSTALLATION

• Attach the panel to the bracket, use the supplied 2.5mm screws.

• The ideal thickness of the mounting surface should be between 1/8” to 1/4”.

• Check to make sure the control wire is long enough to mount the desired location.

• Check the clearance behind the drilling location. Make sure you are not going to drill

through and damage any wiring harness and components in the vehicle.

• Once you decide where to mount, use the bracket to mark the drill location.

• Drill using a 1/8” drill bit, use the supplied pan head coarse screws to attach

• Proceed to Wiring Installation

Switch Panel Mounting

Flush Mount

• There are two different mounting options provided within the HE-SWP8; flush mount (Figure C), and adjustable mount. (Figure D)

(

Figure C

)

(

Figure D

)

*Note: Do not attempt to extend the control wire. Cutting and splicing may void the warranty and damage the product.

Adjustable Mount

• Attach the panel to the bracket, use the supplied 2.5mm screws.

• The ideal thickness of the mounting surface should be between 1/8” to 1/4”.

• Check to make sure the control wire is long enough to mount the desired location.

• Check the clearance behind the drilling location. Make sure you are not going to drill

through and damage any wiring harness and components in the vehicle.

• Once you decide where to mount, use the bracket to mark the drill location.

• Drill using a 1/8” drill bit, use the supplied pan head coarse screws to attach.

• The supplied Hex key can be used to adjust the viewing angle.

• Proceed to Wiring Installation

(

Figure E

)

Wire Connections*

22 g Red Wire

• Recommended connection, the vehicles +12v constant, (always on) circuit.

22 g White Wire

• Recommended connection, the vehicles +12v parking light circuit.

22 g Yellow Wire

• Recommended connection, the vehicles +12v switched source.

6 g Red Wire**

• Recommended connection, the vehicles +12v battery post.

6 g Black Wire**

• Recommended connection, the vehicles - negative battery post.

60 amp Circuit Breaker*

• Connect between the +12v battery and circuit box + input.

Switch Panel

• The IP68 5-pin DIN plug connect the panel to the control box. (Figure F)

Verify Operation

• Once all connections and installation is complete, check the operation of the

HE-SWP8, before reassembling the vehicle.

(

Figure F

)

REV. 12/20/2019 INSTHE-SWP8

INSTALLATION

*Note: Refer to “HEISE

Led Lighting Systems Technical Operation Specification Parameters” pull out for more detailed wiring information

*Attention: If you decide not to use the supplied power and ground wire, consult a wire gauge chart for the correct size and distance.

61.800.221.0932 HeiseLED.com

OPERATION

1. Power Indication LED

2. Power Button (Heise®Atom)

3. Circuit Activation LED

4. Label Placement Area

5. Blue LED Back-lit Area

Switch Panel

A. Accessory Circuit 1

B. Accessory Circuit 2

C. Accessory Circuit 3

D. Accessory Circuit 4

E. Accessory Circuit 5

F. Accessory Circuit 6

G. Accessory Circuit 7

H. Accessory Circuit 8

Indication

1. Red LED lights up when the HE-SWP8 is powered on .

2. Manual power activation button, press to turn on, press to turn off.

3. Red LED lights up to show the accessory circuit is on.

4. Area for placement of selected labels (decal).

5. Blue LED Illumination area; back lighting for the label.

(

Figure G

)

Accessory Circuits 1 - 8 can operate as a latched or momentary.

By default the HE-SWP8 comes out of the box set for switched mode.

To enable or disable the momentary function, follow this procedure.

Ignition must be off (No power to the Yellow wire).

1. Turn on the HE-SWP8 (Press the Heise®Atom then release)

2. Press and hold the Atom for 2 seconds

3. Press and hold the desired accessory button until the corresponding

LED flashes then release the button . If you are successful the LED

will flash once then turn off.

4. Test functionality, if you are unsuccessful power off and repeat

steps 1-4.

Mode

REV. 12/20/2019 INSTHE-SWP8

Advanced Operation

• The HE-SWP8 will power-on one of two ways.

1. With Ignition on (+12v input to yellow 22g wire) press the desired circuit.

2. With ignition off press the Atom.*

• Accessory circuits must be selected every time the HE-SWP8 is powered on.

• Previously activated accessory circuits can resume on . For example; the light bar, whip and light cubes can re-activate together.

• With the HE-SWP8 powered on, only press the Atom button and those circuits will activate and deactivate together.

• If a different circuit is selected the previously activated accessory circuits will be forgotten.

*Note: The previously active circuits will power back on or resume when ever the Atom button is used to power on the HE-SWP8.

OPERATION

(

Figure H

)

HE-SWP8

INSTALLATION INSTRUCTIONS

#HeiseLED

KNOWLEDGE IS POWER

Enhance your installation and fabrication skills by

enrolling in the most recognized and respected

mobile electronics school in our industry.

Log onto www.installerinstitute.com or call

800-354-6782 for more information and take steps

toward a better tomorrow.

Metra Recommends MECP

certified technicians

Having difficulties? We’re here to help.

Contact our Tech Support line at:

1-386-257-1187

Or via email at:

techsupport@metra-autosound.com

Tech Support Hours (Eastern Standard Time)

Monday - Friday: 9:00 AM - 7:00 PM

Saturday: 10:00 AM - 7:00 PM

Sunday: 10:00 AM - 4:00 PM

SPECIFICATIONS

Heiseled.com

LED Lighting Systems

What’s In the Box?

• 8 Gang Switch Panel System

• Control Box with Cover

• 50 Switch Labels

• 14 ATS Fuses (8 operation, 6 spare)

• 60 amp Resettable Circuit Breaker

• Power harness and battery cables

• Switch Panel Brackets (2)

• Control Box Bracket (1)

• Mounting hardware, screws and zip-ties

• Instructions

Details

• Applications: Universal

• Power Handling: 600W - 1200W

• Operation Voltage: 12V - 24V DC

• Maximum Current: 60A

• Operating Temp.: -40°C - +105°C

• Panel Material: Die-cast aluminum

• Control Box Material: Die-cast aluminum

• Panel Size: 4.53 x 0.59 x 2.60 inch

• Circuit Box size: 7.48 x 1.34 x 4.13 inch

Tabla de contenidos

Manuales populares de Accesorios para automóviles de otras marcas

James Baroud

James Baroud Odyssey Manual de usuario

Motorola

Motorola i50sx Manual de usuario

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manual de usuario

Feniex

Feniex T3 Manual de usuario

Renault

Renault 77 11 423 180 Manual de usuario

Kia

Kia E8300-4D000 Manual de usuario

Brink

Brink 756843 Manual de usuario

Whispbar

Whispbar K085W Manual de usuario

v.link

v.link CI-VL2-PC-HSD Manual de usuario

Viking

Viking Stack-Rack Guía de configuración rápida

Aries

Aries 203015 Manual de usuario

Choetech

Choetech AT0005 Manual de usuario

ZZ2

ZZ2 ZZAIR-PRO Manual de usuario

Holman

Holman 4A80L Manual de usuario

Thule

Thule 2075 Manual de usuario

Motorola

Motorola T325 Manual de usuario

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guía de instalación

DV8

DV8 FBJL-02 Manual de usuario