HEATSTRIP Classic THH1500AUL Manual de instrucciones

R A D I A N T O U T D O O R H E A T E R S

OPERATION, INSTALLATION AND MAINTENANCE MANUAL

HEATSTRIP® Indoor

The heater that is a design f e a ture!

R A D I A N T O U T D O O R H E A T E R S

HEATSTRIP® Class ic ( T H H -AUL)

The heater that is a design f e a ture!

OPERATION, INSTALLATION AND MAINTENANCE MANUAL

IMPORTANT INSTRUCTIONS

When using electrical appliances, basic precautions should always be followed to reduce

the risk of fire, electric shock, and injury to persons, including the following:

1 Read all instructions before installing or using this heater.

2 This heater is hot when in use . To avoid burns, do not let bare skin touch hot surfaces.

Keep combustible materials, such as furniture, pillows, bedding, papers, clothes,

etc. and curtains at least feet (0.9mm) from the front of the heater and keep them away

from sides and rear restrictions apply to location dedicated heaters only.)

3 Extreme caution is necessary when any heater is used by or near children or invalids

and whenever the heater is left operating and unattended.

4 Do not operate any heater after it malfunctions. Disconnect power at service panel and

have heater inspected by a reputable electrician before reusing .

5 To disconnect heater, turn controls to off, and turn off power to heater circuit at main

disconnect panel ( or operate internal disconnect switch if provided)

6 A heater has hot and arcing or sparking parts inside. Do not use it in areas where gaso-

line, paint, or flammable vapours or liquids are used or stored.

7 Use this heater only as described in this Manual. Any other use not recommended by

the manufacturer may cause fire, electric shock, or injury to persons

“SAVE THESE INSTRUCTIONS”

INSTALLATION

1 This equipment shall be installed only by qualified personal who are familiar with the

construction and operation of the apparatus and hazard involved.

2 The heater is fitted with an electrical connection box and should be connected as a fixed

installation by a licensed electrical professional in accordance with the relevant electrical

code.

3 Within USA, electrical installation shall be made in accordance with the National Electri-

cal code.

4 Within Canada, electrical installation shall be made according to the provisions of section

62 of the Canadian electrical code Part 1.

5 This appliance must be grounded.

6 An over current protection device (or circuit breaker) is required for proper installation.

The rating of the device should be 150% of the rating of the product.

7 The THX series heaters are designed for domestic/ commercial heating applications

within indoor or outdoor area and should not be used for any other purpose. Any other use

not recommended by the manufacturer may cause fire, electric shock or injury to persons.

8 Before commencing installation make sure the electrical supply voltage is the same as

that shown on the rating plate of the heater.

9 The heater must be mounted at least 6 feet(1.8m) above ground level when installed in

USA and 8 feet (2.4) above ground level when installed in Canada . For other clearances

please refer to the diagram included in these instructions.

10 Do not use heater in areas where gasoline, paint or flammable liquids are used or

stored.

11 The heater is not intended for use in bathrooms, laundry areas or similar indoor areas.

Never locate heater where it may fall into a bathtub, pool, spa or other water container.

12 Do not operate the heater after the heater malfunctions, or has been dropped or dam-

aged in any manner. Return heater to authorised service facility for examination or me-

chanical adjustment or repair.

13 There are no user serviceable parts inside the heater any servicing other then cleaning

of the heater should be performed by an authorised service representative

CAUTION:

High temperature risk of fire, keep electrical cords, drapery, furnishings and other

Combustibles At least feet (0.9m) from front of heater and away from side and rear of

heater.

R A D I A N T O U T D O O R H E A T E R S

Product Overview

Rev D JUN14

Why choose Heatstrip

electric radiant heaters for your outdoor or hard-to-heat indoor area?

As there is typically constant air movement in an outdoor or open indoor area, many conventional patio heaters rely on

convection heating which works by heating the surrounding air. This can be quite impractical for these areas, as this

heated air can easily blow away with natural air movement. Radiant style heaters transfer heat directly to objects through

infra-red waves.

Whilst convection heaters heat the air in between objects, radiant heaters heat the surface of the objects themselves.

HEATSTRIP

electric radiant heaters are more effective within an outdoor or uninsulated indoor area because they

provide targeted warmth directly to the people and objects in their path.

Discrete, stylish heating for undercover outdoor and indoor open areas

Using the radiant heating principle, HEATSTRIP

can provide effective and energy efficient comfort heating for undercover

outdoor and indoor open areas. HEATSTRIP

has successfully enabled many entertainment venues such as restaurants,

pubs and clubs to utilise their outdoor dining areas day and night, through all seasons. Within your workplace or business,

HEATSTRIP

can provide comfort heating for designated outdoor smoking and leisure areas, as well as for workstation

spot heating in factories, warehouses and showrooms. Within your home, HEATSTRIP

can provide comfort heating for

undercover alfresco dining and BBQ area, patios, verandas, courtyards and balconies.

Subtle, minimalist design

The stylish, slimline black face of the HEATSTRIP

does not emit light or glow when in use, blending elegantly into your

décor. Ceiling, wall and umbrella mounting options ensure that your valuable floor and table space is not wasted.

APPLICATION THH

Indoor insulated areas, classrooms, offices, bathrooms, wet areas, drying rooms √

Outdoor under cover, café, veranda, patio, balcony ceiling height 3m or less √

Indoor open area, warehouse, factory, production areas, sports facilities √

Indoor spot heating, above tables, assembly areas √

This is a general guide only, please refer to the Product Manual for each product, for more information.

HEATSTRIP

Classic (THH models) is a premium high temperature heater and is primarily used for outdoor rooms where

there is 1,2 , or 4 enclosed sides, with an ideal mounting height of 82” to 105” (2.1 m to 2.7m.)

R A D I A N T O U T D O O R H E A T E R S

Efficient, cost effective electric heating

The innovative design of the HEATSTRIP

enables comfortable and even heat dispersion from the surface with minimal

operating costs.

Design flexibility

Three HEATSTRIP

models are available, ensuring the heating requirements of any undercover outdoor or open

indoor area is possible. Brackets for direct ceiling or wall/ceiling angled mounting are supplied as standard.

Optional HEATSTRIP

accessories include beam or fixed umbrella mount brackets, extension mount brackets,

chain suspension brackets, twin mount brackets and flush mounting enclosures.

Minimal maintenance

The HEATSTRIP

incorporates no internal moving parts ensuring quiet and virtually maintenance free operation.

Australian made

Designed, engineered and assembled in Australia the HEATSTRIP

,is fully backed by a 12 month warranty.

Stylish design— The Heater that is a Design Feature!

The attractive HEATSTRIP

comes with a standard black face and anodised alloy rear casing.

Easy to use

The standard HEATSTRIP

is controller by a simple on/off operation, either when plugged directly into a power point, or

hard-wired via a wall mounted on/off switch. The unit takes approximately 15 minutes to heat up to maximum temperature

and approximately 0 minutes to cool down, depending upon the ambient temperature. Please don’t forget to turn it off.

R A D I A N T O U T D O O R H E A T E R S

Specifications - AUL

MODEL POWER

(WATTS)

CURRENT

(AMPS)

DIMENSIONS

(inches)

WEIGHT

(lbs)

THH1500AUL 1500 12.2 6” x 6.5” x 2” 11

THH2400AUM 2400 11. 5 .5” x 6.5” x 2” 17.5

THH 200AUM 200 15 70” x 6.5” x 2” 22

VOLTAGE

(VOLTS)

120

208

THH2400AUL 2400 240 10 5 .5” x 6.5” x 2” 17.5

THH 200AUL 200 240 1 70” x 6.5” x 2” 22

NAME

HEATSTRIP MINI

HEATSTRIP REGULAR

HEATSTRIP LARGE

HEATSTRIP CAFE

HEATSTRIP RESTAURANT

MODEL

HEATER TYPE High intensity electric radiant overhead heater with high surface area

profiled alloy

OUTPUT Refer to model code chart above

POWER 120, 208 or 240 Volts Nominal at 50—60 Hertz, Single Phase

CONNECTION Gangbox

APPROVALS CSA/UL E 21448

MOUNTING HEIGHT MINIMUM

RECOMMENDED

MAXIMUM

82” (2.1 m)

90” to 105” (2. m to 2.7 m)

117” ( .0 m) For higher ceiling heights, units can be

lowered using optional bracket kits or refer to the

Heatstrip Max range

PROTECTION RATING IP55 Protection from water ingress from all directions

COUNTRY OF MANUFACTURE Australia

MOUNTING OPTIONS Suitable for ceiling, wall, beam, fixed umbrella and recess mounting. Also

available for extension mount using rigid fixing poles and chain mount

bracket.

6" (924mm)

2" (42mm)

5.5" (164mm)

70" (1774mm)

THH1800A

THH2400A

THH 200A

6.5" (172mm)

2" (42mm)

THH1500A

R A D I A N T O U T D O O R H E A T E R S

BAR

BAR STOOLS

DINING TABLE

LOUNGE

BBQ

2 x THH24006 x THH2400

Spot heating principle

In most outdoor or difficult-to-heat indoor applications, there are 2 options when looking at the size and quantity

of the heater required. Option 1 is to comfort heat the entire area based on the total dimensions of the space,

regarding of whether the entire area is being fully occupied. Option 2 is to spot heat the high use areas, such as

over outdoor tables, BBQ’s, lounges, assembly lines or indoor workstation.

Often it is more practical and efficient to spot heat these areas. Spot heating will help to reduce the initial capital

cost, as well as the running costs. Spot heating will allow the area to be “zoned”, meaning heating only the areas

that are being used, such as tables in a restaurant or outdoor alfresco area.

The top table shows a comparison between spot heating over a table, or heating an entire area.

The bottom table shows the flexibility of using HEATSTRIP

to provide a comfortable environment, even when

the layout of the area is very unusual.

6 x HEATSTRIP REGULAR 2 x HEATSTRIP REGULAR

R A D I A N T O U T D O O R H E A T E R S

77°F

70°F

1" STANDING HEIGHT

45" SITTING HEIGHT

94" MAXIMUM HEIGHT

54°

7 °F

58"

54"

78"

110"

Radiant footprint

HEATSTRIP

electric heater produce radiant heat,

which heats objects rather than the air. Therefore, it is

imperative that objects to be heated (ie. People), are

within the direct radiant footprint of the heater.

The diagram to the left shows the radiant footprint of

HEATSTRIP

, and is an approximate guide based on

a fully enclosed, outdoor environment.

This diagram shows that the maximum heat output is

found directly under the heater, and the temperature

decreases as you move away from the heater.

It highlights the importance of maintaining

recommended mounting heights, and positioning the

heater directly above the area to be heated, if possible.

Also, the temperature (ie. surface temperature) is the

same for all models, regardless of the wattage.

However, the size increases and the length of the unit

increases, the radiant footprint will be larger.

The below diagrams show the approximate heating

area for each model, based on both an indoor and

outdoor enclosed environment.

1 7"

82"

70"

LARGE

102"

82"

55"

REGULAR

62"

82"

MINI

HEATED AREA

INDOOR SPOT HEATING

105"

82"

70"

78"

82"

55"

50"

82"

HEATED AREA

OUTDOOR ENCLOSED AREA

MINI

REGULAR

LARGE

R A D I A N T O U T D O O R H E A T E R S

Selection guide

Prior to selecting the exact model and quantity required for your application, please ensure the correct model heater is

being used.

HEATSTRIP

Classic (THH models) is a premium high temperature heater and is primarily used for outdoor rooms where

there is 1,2 or 4 enclosed sides, with an ideal mounting height of 82” to 105” (2.1 m to 2.7m.) Ideal for hard to heat in-

door applications or moist environments where an IP55 rating is required.

General recommendations for HEATSTRIP

Classic:

• Ideal mounting height: 82” to 105” (2.1 m to 2.7m.) Maximum is 117” ( m) in a protected outdoor environment.

• Ideal mounting location: ceiling mounted, directly above area to be heated (eg. above a table)

• Based on the radiant footprint of the previous page, for a protected outdoor area, a minimum of 500W/m2 is re-

quired. For indoor spot heating, a minimum heating capacity of 400W/m2 is recommended.

The below table outlines the coverage of each HEATSTRIP

Classic model (in m2), based on different scenarios.

For example, for all outdoor area that is protected from prevailing winds by walls, café blinds etc, Model Heatstrip Mini will

cover 2 ft2 and Model Heatstrip Regular will cover 52 ft2.

MODEL INDOOR PROTECTED (ft

) OUTDOOR ENCLOSED (ft

) OUTDOOR EXPOSED (ft

)

HEATSTRIP MINI

( .75 m2)

( m2)

(2.5 m2)

HEATSTRIP REGULAR

(6 m2)

(4.8 m2)

(4 m2)

HEATSTRIP LARGE

(8 m2)

(6.4 m2)

(5. m2)

R A D I A N T O U T D O O R H E A T E R S

Table layout

For the majority of outdoor applications, the most effective method is to spot heat a table or similar area. The below dia-

grams provides an easy selection guide for the approximate model and quantity of heaters required to heat common resi-

dential table settings.

Selections are based on HEATSTRIP

Classic being mounted at 94” (2.4m) from the floor and an undercover fully en-

closed outdoor area.

HEATSTRIP MINI HEATSTRIP REGULAR HEATSTRIP LARGE

2 x HEATSTRIP REGULAR

2 x HEATSTRIP LARGE

2 x HEATSTRIP MINI

4 x HEATSTRIP MINI

HEATSTRIP REGULAR

HEATSTRIP LARGE

Otros manuales para Classic THH1500AUL

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Calentador de HEATSTRIP

HEATSTRIP

HEATSTRIP TT2200RW Manual de usuario

HEATSTRIP

HEATSTRIP THX 2400 Manual de usuario

HEATSTRIP

HEATSTRIP THH1500AEU Manual de instrucciones

HEATSTRIP

HEATSTRIP Classic Manual de usuario

HEATSTRIP

HEATSTRIP THX2400UK Manual de instrucciones

HEATSTRIP

HEATSTRIP THE1800 Manual de usuario

HEATSTRIP

HEATSTRIP THH 1500 Manual de instrucciones

HEATSTRIP

HEATSTRIP THE 1800 Manual de instrucciones

HEATSTRIP

HEATSTRIP Classic THH-A Series Manual de usuario

HEATSTRIP

HEATSTRIP TF2200RW Manual de usuario

HEATSTRIP

HEATSTRIP THH1500 Manual de instrucciones

HEATSTRIP

HEATSTRIP TG2200RB Manual de usuario

HEATSTRIP

HEATSTRIP Design THH Series Manual de instrucciones

HEATSTRIP

HEATSTRIP THH1800AP Manual de usuario

HEATSTRIP

HEATSTRIP THE3200R Manual de usuario

HEATSTRIP

HEATSTRIP Elegance THE1800EU Manual de instrucciones

HEATSTRIP

HEATSTRIP THX 2400 Manual de instrucciones

HEATSTRIP

HEATSTRIP Indoor THS-A Manual de usuario

HEATSTRIP

HEATSTRIP THX 2400 Manual de usuario

Manuales populares de Calentador de otras marcas

oventrop

oventrop Regucor Series Manual de usuario

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manual de usuario

ELMEKO

ELMEKO ML 150 Manual de usuario

BN Thermic

BN Thermic 830T Manual de usuario

KING

KING K Series Guía

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guía de inicio rápido

Well Straler

Well Straler RC-16B Manual de usuario

EUROM

EUROM 333299 Manual de usuario

Heylo

Heylo K 170 Manual de usuario

Eterna

Eterna TR70W Manual de usuario

Clarke

Clarke GRH15 Manual de instrucciones

IRSAP

IRSAP The Radiator Company Ovali Manual de usuario

Empire Heating Systems

Empire Heating Systems WCC65 Manual de usuario

Wetekom

Wetekom 92 86 43 Manual de usuario

Desa

Desa SPC170-F Manual de usuario

Watlow

Watlow Watrod Electric Tubular Heaters Manual de usuario

Haverland

Haverland ECO-DRY GPS Series Manual de lista de piezas

Stelpro

Stelpro ASILVC2060 Series Manual de usuario