Heatstore HSDHHR070 Manual de usuario

- 1 -

Dynamic High Heat Retention

(HHR) Storage Heater Models:

HSDHHR050, HSDHHR070, HSDHHR100

HSDHHR125, HSDHHR150

INSTALLATION MANUAL

08/83006/0 ISSUE: 1

- 2 -

Warnings in this document are identiﬁed by a warning triangle against a grey

background.

Keywords at the start of a warning indicate the type and seriousness of the

ensuing risk if measures to prevent the risk are not taken.

The following keywords are deﬁned and can be used in this document:

○DANGER indicates a hazardous situation which, if not avoided, will result in death or

serious injury.

○WARNING indicates a hazardous situation which, if not avoided, could result in death

or serious injury.

○CAUTION indicates a hazardous situation which, if not avoided, could result in minor

to moderate injury.

○NOTICE is used to address practices not related to personal injury.

IMPORTANT

THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR

FUTURE REFERENCE. Note also the information presented on the appliance

CAUTION

FAILURE TO FOLLOW THESE INSTRUCTIONS MAY CAUSE INJURY AND/OR DAMAGE

AND MAY INVALIDATE YOUR GUARANTEE

IMPORTANT SAFETY ADVICE

When using electrical heaters, basic precautions should always be followed to reduce the risk of

ﬁre, electrical shock, and injury to persons, including the following:

IMPORTANT – The wall bracket supplied with the heater must be used.

IMPORTANT – All packaging should be disposed of in an appropriate manner.

OVERHEATING WARNING

WARNING - In order to avoid overheating, do not cover or obstruct the heater. Do not place

material or garments on the heater, or obstruct the air circulation around the heater, for instance

by curtains or furniture, as this could cause overheating and a ﬁre risk. NEVER cover or obstruct in

any way the heat outlet slots at the top of the heater or the air outlet slots in the base of the heater.

WARNING - THE SURFACES ON THIS HEATER CAN BE HOT.

The heater carries a warning ‘DO NOT COVER’ to alert the user to the risk of ﬁre that exists

if the heater is accidentally covered.

CAUTION - Some parts of this product can become very hot and cause burns.

Particular attention has to be given where children and vulnerable people are present.

For your safety this heater is ﬁtted with a thermal cut-out. In the event that the product overheats

for some reason, the cut-out prevents excessive temperatures on the product by cutting the power

to the heater. Once the heater has cooled down, it will reset automatically, it will continue to cycle

on and off automatically until the reason for overheating is removed.

The display screen may ﬂash red to indicate the product has overheated. To reset the display,

remove the obstruction and hold Enter for 10 seconds.

- 3 -

SUITABLE APPLICATIONS

WARNING - This heater is suitable for normal dwelling purposes and should not be used in any

other type of environment. This product should only be used in the country where it was purchased

from by a recognised commercial retailer. Do not use outdoors.

SERVICING AND REPAIRS

WARNING - Servicing and product repairs should only be undertaken by the manufacturers

approved service agent or a similarly trained or qualiﬁed person, using only exact manufacturer

approved spare parts.

PLEASE NOTE: Household dust, lit cigarettes, candles and oil burners, combined with the

convection effect of electric heaters can cause signiﬁcant soot deposits to build up on the surface

directly above and to the sides of the heater. This is not a fault of the heater. Extensive burning of

candles or smoking in the operating environment of this product can produce heavy discolouration

within a few months of use.

OPERATING WARNINGS

IMPORTANT:Remember to observe all safety warnings and precautions when operating

the heater on the automatic or timer modes, either attended or unattended since a ﬁre risk exists

when the heater is accidentally covered, obstructed or displaced.

CAUTION:Do not use if either of the heater’s mains power leads become damaged. If the

supply cord is damaged it must be replaced by the installer or an approved Heatstore service

partner.

Do not sit or stand on the heater.

Ensure minimum clearances between the heater and other objects / surfaces are maintained.

ELECTRICAL INSTALLATION

WARNING - Minimum clearances and IP zone requirements must be adhered to in

accordance with the current wiring regulations.

Mains cables are not provided with this heater.

WARNING - The electrical installation of this heater must be carried out by a suitably qualiﬁed

or trained electrician, and be in strict accordance with current wiring regulations.

The peak supply must be connected via a switched fused spur with a fuse rated suitably for the

appliances "ex, the off-peak supply, via a 20A double pole isolated switch. In both instances a

plug and socket arrangement MUST NOT be utilised. The contact separation to be a minimum of

3mm.

Failure to follow these instructions will mean that the manufacturer’s instructions have not been

adhered to. THERE ARE NO EXCEPTIONS.

• This heater must be earthed

• Not suitable for connection via a plug top

• Do not locate the heater immediately above, below or in front of a !xed electrical point i.e. socket

outlet.

This appliance is intended for installation to a single phase supply only and is not suitable for

connection to 3 phase supplies.

- 4 -

ELECTRICAL INSTALLATION continued

The heater is not !tted with a mains cable, this should be !tted by the installer. Cable type (minimum

size) H05VV-F 1.5mm² three core for peak and 2.5mm² three core for off-peak for connection

to the !xed wiring of the premises through suitable isolation devices positioned adjacent to the

heater. The supply circuits to the heater must incorporate a double pole isolating switch having a

contact separation of at least 3mm.

In installation the supply cord must be cut to the appropriate length for the electrical connection

point. Excess cable should not be inserted or stored behind the heater.

If, during reassembly of the heater, a part of the thermal insulation shows damage or deterioration,

it should be replaced by an identical part.

WARNING:All electrical connections to the terminal block must be secure to prevent risk of

ignition. Tighten to 2 Nm.

CHILD SAFETY

WARNING - Fixing kit screws are a potential choking hazard.

WARNING - This appliance is not intended for use by persons (including children) with

reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning use of appliance by a person

responsible for their safety.

This appliance can be used by children from 8 years and above and persons with reduced

physical, sensory or mental capabilities or lack of experience and knowledge if they have been

given supervision or instruction concerning use of the appliance.

Children shall not play with the appliance.

Cleaning and user maintenance shall not be made by children without supervision.

Children of less than 3 years should be kept away unless continuously supervised.

Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided

that it has been placed or installed in its intended normal operating position and they have been

given supervision or instruction concerning use of the appliance in a safe way and understand

the hazards involved.

Children aged from 3 years and less than 8 years shall not regulate and clean the appliance or

perform user maintenance.

WARNING - KEEP BATTERIES OUT OF REACH OF CHILDREN

WARNING - Packaging should be disposed of responsibly as the EPS used could be

a potential choking hazard for children.

- 5 -

iThis document is customer property and is to remain with this unit.

These instructions do not cover all the different variations of systems nor does it

provide for every possible contingency to be met in connection with installation.

This appliance must be earthed in accordance with the manufacturers

recommendations and in accordance with IEE regulations for electrical

equipment.

Failure to adequately earth the appliance can result in electrical shock causing

severe personal injury or death.

WARNING: EARTHING

Disconnect all power to unit before installing or servicing.

Hazardous voltage can cause severe personal injury or death.

WARNING: HAZARDOUS VOLTAGE

If the supply cables to the appliance are damaged in anyway, they must be

immediately replaced by a competent person in order to avoid electrocution

which could cause severe personal injury or death.

WARNING: ACCESS TO LIVE PARTS

The appliance must be securely !xed to the wall. The installed appliance could

weigh up to 165kg and if it falls off the wall it could cause severe personal injury

or death. It is the responsibility of the installer to ensure that the appropriate wall

!xing is used and that the "oor is capable or bearing the full weight.

WARNING

- 6 -

To avoid a !re hazard the cardboard insert within the heater core must be

removed before the heater is switched on. Also ensure all polystyrene packaging

is removed before the heater is operated. Leaving combustible packaging in the

appliance could lead to !re and cause severe personal injury, death and damage

to property.

WARNING

The appliance is very heavy (up to 50kg) and care should be taken when

handling during installation to reduce risk of muscular or skeletal injuries.

CAUTION

The appliance should not be repeatedly switched on/off by an external room

thermostat as this could lead to failures of the electronic controller and may

invalidate the guarantee – further clari! cation SHOULD BE SOUGHT FROM

THE HELPLINE on 0117 923 5375 or visit https://heatstore.co.uk/#contact and

complete the online form.

During the !rst 48 hours of operation rooms must be well ventilated as the heater

will produce a smell. Young children, caged birds, or persons with respiratory

complaints must not remain in close proximity to the appliance during the !rst 48

hours or operation.

CAUTION

iIt is important that the appliance bricks are dry and free from mould growth. Wet

or mouldy bricks can lead to an unpleasant odour and or steam being generated

by the appliance which could upset the customer.

- 7 -

- 8 -

Energy Related Product Directive

Technical Details

Model Identiﬁ er(s): HSDHHR

050

HSDHHR

070

HSDHHR

100

HSDHHR

125

HSDHHR

150

Input rating +5% / -10% 936/1020W 1435/1560W 2042/2220W 2540/2760W 3024/3300W

Boost Output 230/240V~ 312/340W 478/520W 681/740W 847/920W 1008/1100W

Rated Charge Period: 7.7 - 7 Hours 7.7 - 7 Hours 7.7 - 7 Hours 7.7 - 7 Hours 7.7 - 7 Hours

Max Storage Capacity 7.2kWh 10.9kWh 15.4kWh 19.3kWh 23.1kWh

Fan Wattage 11W 11W 11W 11W 11W

UI Wattage 0.5W 0.5W 0.5W 0.5W 0.5W

Sound Level dB

(measured in test chamber) 27 29 32 30 31

Energy Cell Packs Required (047243) 4 6 8 10 12

Height (mm) 730 730 730 730 730

Width (mm) 580 703 865 1069 1069

Depth (mm) 185 185 185 185 185

Model Identiﬁ er(s): HSDHHR

050

HSDHHR

070

HSDHHR

100

HSDHHR

125

HSDHHR

150

Heat Output

Nominal heat output Pnom 0.50kW 0.75kW 1.00kW 1.25kW 1.50kW

Minimum heat output (indicative) Pmin

0.00 0.00 0.00 0.00 0.00

Maximum heat output Pmax,c 0.90kW 1.20kW 1.50kW 1.70kW 2.00kW

Auxiliary electricity consumption

At nominal heat output elmax 0.00 0.00 0.00 0.00

0.00

At minimum heat output elmin

0.00 0.00 0.00 0.00 0.00

In standby mode elSB 0.000 0.000 0.000 0.000 0.000

Type of Heat input, for electronic storage local space heaters only

Electronic heat charge control with room

temperature feedback Yes

Fan assisted heat output Yes

Type of heat output / room temperature control

Electronic room temperature control plus week timer Yes

This product meets the Ecodesign requirements for an electric storage local space heater. Commission Regulation (EU)

2015/1188.

Contact details

Heatstore

Unit 12, Access 18, Bristol, BS11 8HT

Tel: 0117 923 5375

This product meets the Ecodesign requirements for an electric storage local space heater. Commission Regulation (EU)

2015/1188.

- 9 -

All Models

Controls

Digitally controlled, Electronic Thermostat accurate to (±0.2°C).

Timer modes:

7 Day Programmable User Timer, Out All Day, Home All Day

Continuous heat modes:

Frost Protect

Additional Modes:

Away, Boost, Setback

Controller UI

• Graphical display with RGB backlight

• Tactile buttons with audio feedback

• User replaceable battery (Coin-Type)

• Open window detection, Adaptive Start, Advance Time Period

• Wide SP range (7-30°C)

• Automatic Charge Control

• History / Reporting Screens

• Boost Mode, User Adjustable

• Heat Demand % Adjustment

• Child Lock & Heater Lock (PIN-based)

Safety

Electronic overheat protection.

Additional electromechanical overheat protection.

LVD and EMC compliance.

IP Rating IPX4

Battery 3.3V coin cell battery to backup real time clock. Battery life > 5 years.

Supply 1/N/1/N/PE ~230-240V (Peak + Off Peak) 230-240V / 50Hz Class II

Colour / Finish Traf!c White (RAL 9016),

Grille RAL7035

Storage Core High-density bonded magnetite energy cells

Approvals CE, BEAB

Guarantee 2 Years

10 Years extended available with registration

Country of Origin United Kingdom

Manufacturer Heatstore

- 10 -

Preparation

Do not place objects within 300mm of the front of the heater

and 150mm either side.

150mm 150mm

‘W’

730mm

The appliance is very heavy (up to 50kg) and care should be taken when

handling during installation to reduce risk of muscular or skeletal injuries.

CAUTION

Model W (mm)

HSDHHR050 580

HSDHHR070 703

HSDHHR100 865

HSDHHR125 1069

HSDHHR150 1069

Fig. 1

150mm

300mm

250mm

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Calentador de Heatstore

Heatstore

Heatstore HSAC3 Manual de usuario

Heatstore

Heatstore HSOFR1500TX Manual de usuario

Heatstore

Heatstore HS1500C Manual de usuario

Heatstore

Heatstore DYNAMIC HSDR500T Instrucciones de funcionamiento

Heatstore

Heatstore HSQH2000 Manual de usuario

Heatstore

Heatstore HS2020XCN Manual de usuario

Heatstore

Heatstore HSACW9000 Manual

Heatstore

Heatstore HSQH3000 Manual de usuario

Heatstore

Heatstore HSAC9000E Manual de usuario

Heatstore

Heatstore HSCEH7115N Manual

Heatstore

Heatstore HS2020TXN Manual de usuario

Heatstore

Heatstore HS2000T Manual de usuario

Heatstore

Heatstore Dynamic InteliPlinth HSDBU24 Manual de usuario

Heatstore

Heatstore HSQWPH1500N Manual de usuario

Heatstore

Heatstore HSAC6000X Manual

Heatstore

Heatstore HSAC9000CX Manual

Heatstore

Heatstore HSPBRF Manual de usuario

Heatstore

Heatstore HSRCH4500RF Manual de usuario

Heatstore

Heatstore HSXCA12X Manual de usuario

Heatstore

Heatstore HSFAH30 Manual de usuario

Heatstore

Heatstore HS2000X Manual de usuario

Heatstore

Heatstore HSAC9000X Manual

Heatstore

Heatstore HSACR X Series Manual de usuario

Heatstore

Heatstore HS2000X Manual de usuario

Manuales populares de Calentador de otras marcas

oventrop

oventrop Regucor Series Manual de usuario

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manual de usuario

ELMEKO

ELMEKO ML 150 Manual de usuario

BN Thermic

BN Thermic 830T Manual de usuario

KING

KING K Series Guía

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guía de inicio rápido

Well Straler

Well Straler RC-16B Manual de usuario

EUROM

EUROM 333299 Manual de usuario

Heylo

Heylo K 170 Manual de usuario

Eterna

Eterna TR70W Manual de usuario

Clarke

Clarke GRH15 Manual de instrucciones

IRSAP

IRSAP The Radiator Company Ovali Manual de usuario

Empire Heating Systems

Empire Heating Systems WCC65 Manual de usuario

Wetekom

Wetekom 92 86 43 Manual de usuario

Desa

Desa SPC170-F Manual de usuario

Watlow

Watlow Watrod Electric Tubular Heaters Manual de usuario

Haverland

Haverland ECO-DRY GPS Series Manual de lista de piezas

Stelpro

Stelpro ASILVC2060 Series Manual de usuario