Heat-N-Glo CFX-DIAMOND Instrucciones de montaje

Model:

CFX-DIAMOND Installers Guide

593-900H 8/02

Underwriters

LaboratoriesListed

- Do not store or use gasoline or other flam-

mablevaporsandliquidsinthevicinityofthis

orany other appliance.

-What to do if you smell gas

• Do not try to light any appliance.

• Do not touch any electrical switch.

• Do not use any phone in your building.

• Immediately call your gas supplier from a

neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call

thefiredepartment.

- Installationandservicemustbeperformedbya

qualified installer, service agency, or the gas

supplier.

WARNING: IMPROPER INSTALLA-

TION, ADJUSTMENT, ALTERATION,

SERVICE OR MAINTENANCE CAN

CAUSE INJURY OR PROPERTY DAM-

AGE. REFER TO THIS MANUAL. FOR

ASSISTANCE OR ADDITIONAL INFOR-

MATION CONSULT A QUALIFIED IN-

STALLER, SERVICEAGENCY, OR THE

GAS SUPPLIER.

READ THIS MANUAL BEFORE INSTALLING OR

OPERATING THIS APPLIANCE. THIS INSTALLERS

GUIDE MUST BE LEFT WITH APPLIANCE FOR

FUTUREREFERENCE.

1.Thisappliancemaybeinstalledin anaf-

termarket,permanently located,manu-

factured(mobile) home, where not pro-

hibitedby local codes.

2. Thisapplianceisonlyforusewiththetype

of gas indicated on the rating plate. This

appliance is not convertible for use with

othergases,unlessacertifiedkitisused.

Please contact your Heat-N-Glo dealer with any

questionsorconcerns.Forthenumberofyournearest

Heat-N-Glo dealer, please call 1-888-427-3973.

Heat-N-Glo,adivisionofHearthTechnologiesInc.

20802KensingtonBoulevard,Lakeville,MN55044

WARNING: IF THE INFORMATION

IN THESE INSTRUCTIONS IS NOT

FOLLOWED EXACTLY,AFIRE OR

EXPLOSION MAY RESULT CAUS-

ING PROPERTY DAMAGE, PER-

SONAL INJURY, OR DEATH.

This product is covered by one or more of the following patents: (United States) 4,112,913; 4,408,594; 4,422,426; 4,424,792; 4,520,791; 4,793,322;

4,852,548; 4,875,464; 5,000,162; 5,016,609; 5,076,254 5,191,877; 5,218,953; 5,328,356; 5,429,495; 5,452,708; 5,542,407; 5,613,487; (Australia)

543790; 586383; (Canada) 1,123,296; 1,297,746; 2,195,264; (Mexico) 97-0457; (New Zealand) 200265; or other U.S. and foreign patents pending.

SAFETY AND WARNING INFORMATION

READ and UNDERSTAND all instructions carefully before starting the installation.

FAILURE TO FOLLOW these installation instructions may result in a possible fire

hazard and will void the warranty.

Prior to the first firing of the fireplace, READ the Using Your Fireplace section of the

Owners Guide.

DO NOT USE this appliance if any part has been under water. Immediately CALL a

qualified service technician to inspect the unit and to replace any part of the control

system and any gas control which has been under water.

THIS UNIT IS NOT FOR USE WITH SOLID FUEL.

Installation and repair should be PERFORMED by a qualified service person. The

appliance and venting system should be INSPECTED before initial use and at least

annually by a professional service person. More frequent cleaning may be required due

to excessive lint from carpeting, bedding material, etc. It is IMPERATIVE that the unit’s

control compartment, burners, and circulating air passageways BE KEPT CLEAN to

provide for adequate combustion and ventilation air.

Always KEEP the appliance clear and free from combustible materials, gasoline, and

other flammable vapors and liquids.

NEVER OBSTRUCT the flow of combustion and ventilation air. Keep the front of the

appliance CLEAR of all obstacles and materials for servicing and proper operations.

Due to the high temperature, the appliance should be LOCATED out of traffic areas

and away from furniture and draperies. Clothing or flammable material SHOULD NOT

BE PLACED on or near the appliance.

Children and adults should be ALERTED to the hazards of high surface temperature

and should STAY AWAY to avoid burns or clothing ignition. Young children should be

CAREFULLY SUPERVISED when they are in the same room as the appliance.

These units MUST use one of the vent systems described in the Installing the Fireplace

section of the Installers Guide.NO OTHER vent systems or components MAY BE USED.

This gas fireplace and vent assembly MUST be vented directly to the outside and

MUST NEVER be attached to a chimney serving a separate solid fuel burning

appliance. Each gas appliance MUST USE a separate vent system. Common vent

systems are PROHIBITED.

INSPECT the external vent cap on a regular basis to make sure that no debris is

interfering with the air flow.

The glass door assembly MUST be in place and sealed, and the trim door assembly

MUST be in place on the fireplace before the unit can be placed into safe operation.

DO NOT OPERATE this appliance with the glass door removed, cracked, or broken.

Replacement of the glass door should be performed by a licensed or qualified service

person. DO NOT strike or slam the glass door.

The glass door assembly SHALL ONLY be replaced as a complete unit, as supplied

by the gas fireplace manufacturer. NO SUBSTITUTE material may be used.

DO NOT USE abrasive cleaners on the glass door assembly. DO NOT ATTEMPT to

clean the glass door when it is hot.

Turn off the gas before servicing this appliance. It is recommended that a qualified

service technician perform an appliance check-up at the beginning of each heating

season.

Any safety screen or guard removed for servicing must be replaced before operating

this appliance.

DO NOT place furniture or any other combustible household objects within 36

inches of the fireplace front.

Safety and Warning Information ........................ 2

Service Parts...................................................... 4

Section 1: Approvals and Codes ....................... 6

Appliance Certification .......................................... 6

Installation Codes ................................................. 6

HighAltitude Installations....................................... 6

Section 2: Getting Started ................................. 7

Introducing the Heat-N-Glo Gas Fireplaces........... 7

Pre-installation Preparation................................... 7

Section 3: Installing the Fireplace ................... 9

Constructing the Chase........................................ 9

Step1 Locating the Fireplace............................. 10

Step2 Framing the Fireplace............................. 11

Step 3 Installing the Vent System ....................... 12

A. VentSystemApprovals ....................... 12

B. Installing Vent Components ................ 18

C.VentTermination................................. 23

Step4 Positioning,Leveling,and

Securing the Fireplace............................ 28

Step5 The Gas Control Systems ...................... 28

Step6 The Gas Supply Line .............................. 29

Step7 Gas Pressure Requirements .................. 30

Step8 Wiring the Fireplace................................ 31

Step 9 Finishing ................................................. 32

Step10 Installing Trim, Logs & Ember Material... 34

Installing the Trim................................... 34

Shutter Settings ..................................... 34

Positioning the Logs .............................. 35

Placing the Ember Material .................... 35

Step11 Before Lighting the Fireplace ................. 37

Step12 Lighting the Fireplace............................. 37

AftertheInstallation............................................. 37

Section 4: Maintaining and Servicing

Your Fireplace ............................... 38

Table of

Contents

= Contains updated information.



Approval Listings

and Codes Appliance Certification

The Heat-N-Glo fireplace model discussed in this

Installers Guide has been tested to certification

standards and listed by the applicable laboratories.

CERTIFICATION

MODEL LABORATORY TYPE STANDARD

CFX-DIAMOND Underwriters Direct Vent ANSIZ21.88 -2000/

Laboratories Gas Fireplace CSA2.33-M98 •UL307B

Heater

Installation Codes

Thefireplaceinstallationmust conform tolocalcodes.Beforeinstalling the fireplace,

consult the local building code agency to ensure that you are in compliance with all

applicable codes, including permits and inspections.

Intheabsence of local codes,thefireplaceinstallation must conform tothe National

FuelGasCodeANSIZ223.1(intheUnitedStates)ortheCAN/CGA-B149Installation

Codes (in Canada). The appliance must be electrically grounded in accordance

with local codes or, in the absence of local codes with the National Electric Code

ANSI/NFPANo. 70 (in the United States), or to the CSA C22.1 Canadian Electric

Code (in Canada).

These models may be installed in a bedroom or bed-sitting room in the U.S.A. and

Canada.

HighAltitudeInstallations

UL Listed gas fireplaces are tested and approved for elevations from 0 to 2,000

feet in the U.S.A., and from 0 to 4,500 feet in Canada.

Wheninstallingthisfireplaceatanelevationabove2,000feet(intheUnited States),

it may be necessary to decrease the input rating by changing the existing burner

orifice to a smaller size. Input should be reduced four percent (4%) for each 1,000

feet above sea level, unless the heating value of the gas has been reduced, in

which case this general rule will not apply. To identify the proper orifice size, check

with the local gas utility.

When installing this fireplace at an elevation between 2,000 and 4,500 feet (in

Canada), the input rating must be reduced by ten percent (10%).

When installing this fireplace at an elevation above 4,500 feet (in Canada), check

with local authorities.

Consult your local gas utility for assistance in determining the proper orifice for

your location.

Approvals

and Codes

Approvals

and Codes

Introducing the

Heat-N-Glo

Fireplaces

Heat-N-Glodirect vent gas fireplaces are designed

to operate with all combustion air siphoned from

outside of the building and all exhaust gases

expelled to the outside.

The information contained in this Installers Guide,

unless noted otherwise, applies to all models and gas

control systems.

Gas fireplace diagrams, including the dimensions, are

shown in this section.

Pre-installation

Preparation This gas fireplace and its components are tested and

safe when installed in accordance with this Installers

Guide. Report to your dealer any parts damaged in

shipment, particularly the condition of the glass.Do

not install any unit with damaged, incomplete, or

substitute parts.

The vent system components are shipped in separate

packages. The gas logs are packaged separately and

must be field installed. Read all of the instructions

before starting the installation. Follow these

instructions carefully during the installation to

ensure maximum safety and benefit. Failure to

follow these instructions will void the owner’s

warranty and may present a fire hazard.

TheHeat-N-Glo Warrantywillbevoidedby, andHeat-

N-Glo disclaims any responsibility for, the following

actions:

• Installationof any damaged fireplace orventsystem

component.

• Modification of the fireplace or direct vent system.

• Installationother thanasinstructedbyHeat-N-Glo.

• Improper positioning of the gas logs or the glass

door.

• Installationand/oruseof any component part not

manufacturedand approvedbyHeat-N-Glo,not

withstandinganyindependent testinglaboratoryor

other party approval of such component part or

accessory.

ANY SUCH ACTION MAY POSSIBLY CAUSE A

FIRE HAZARD.

Getting

Started

8Figure 1. Diagram of the CFX-DIAMOND

When planning a fireplace installation, it’s necessary to determine:

•Where the unit is to be installed.

•The vent system configuration to be used.

•Gas supply piping.

•Electrical wiring.

•Framing and finishing details.

•Whether optional accessories—devices such as a wall switch, or remote

control—are desired.

If the fireplace is to be installed on carpeting or tile, or on any combustible

material other than wood flooring, the fireplace should be installed on a metal or

wood panel that extends the full width and depth of the fireplace.

9 3/4 (248mm)

Ø 8 5/8 (Ø 219mm)

41 7/16 (1053mm)

(965mm)

37 7/8

(962mm) 1 7/8

(48mm)

5 9/16

(141mm)

MINIMUM DISTANCE TO HORIZONTAL

COMBUSTIBLE SURFACE (FLOOR, HEARTH, ETC.)

GAS

ACCESS

4 1/2

(114mm)

ELECTRICAL

ACCESS

34 1/2

(876mm)

13 1/2

(344mm)

21 3/4

(552mm)

8 1/2

(219mm)

GAS LINE

ACCESS ELECTRICAL

ACCESS

STANDOFFS

NAILING

TAB

GAS

CONTROLS

RATING PLATE

AND LABELS

NAILING

TAB

NON-COMBUSTIBLE

BOARD

GLASS RETENTION

CLIPS (8)

VENT STARTING

COLLARS

Installing the

Fireplace

Constructing the Fireplace Chase

Achaseisaverticalbox-likestructurebuiltto enclose

thegasfireplaceand/oritsventsystem.Verticalvents

that run on the outside of a building may be, but are

not required to be, installed inside a chase.

TREATMENT OF FIRESTOPSPACERSAND CON-

STRUCTION OF THE CHASE MAY VARY WITH

THE TYPE OFBUILDING. THESE INSTRUCTIONS

ARE NOT SUBSTITUTES FOR THE REQUIRE-

MENTS OF LOCAL BUILDING CODES. THERE-

FORE, YOUR LOCAL BUILDING CODES MUST

BE CHECKED TO DETERMINE THE REQUIRE-

MENTS FOR THESE STEPS.

Factory-built fireplace chases should be constructed

in the manner of all outside walls of the home to pre-

ventcoldairdraftingproblems.Thechaseshouldnot

break the outside building envelope in any manner.

Thismeansthat the walls,ceiling,baseplate and can-

tilever floor of the chase should be insulated. Vapor

and air infiltration barriers should be installed in the

chase as per regional codes for the rest of the home.

Additionally, Heat-N-Glo recommends that theinside

surfaces be sheetrocked and taped for maximum air

tightness.

To further prevent drafts, the firestops should be

caulked to seal gaps. Gas line holes and other open-

ings should be caulked or stuffed with insulation. If

the unit is being installed on a cement slab, we rec-

ommendthata layerofplywoodbe placedunderneath

to prevent conducting cold up into the room. Be sure

toincludespark arrestorsforwoodburningunits ifthey

are required.

THE CHASE SHOULD BE CONSTRUCTED SO

THAT ALL CLEARANCES TO THE FIREPLACE

ARE MAINTAINED AS SPECIFIED WITHIN THIS

INSTALLERS GUIDE.

CAUTION:

Figure 2. Fireplace Dimensions, Locations,

and Space Requirements for

model CFX-Diamond

Clearance Requirements

The top, back, and sides of the fireplace are defined

bystand-offs.

Minimum Clearances from the Fireplace to

Combustible Materials

Glass Rear of Sides of Top of

Front Floor Fireplace Fireplace Fireplace Ceiling

36 inches 5 9/16” 1/2 inch 1/2 inch 3-1/2 inches 31 inches

(914 mm) (141 mm) (13 mm) (13 mm) (89 mm) (787 mm)

The minimum clearance to a perpendicular wall extending

past the face of the fireplace is 4-inches (102 mm).

Thebackofthefireplacemayberecessed213/4inches

(552 mm) into combustible construction.

A BCD E

42 7/16” 21 3/4” 35 7/8” 71 7/8” 50 7/8”

(1078mm) (552mm) (913mm) (1825mm) (1291mm)

FGHI

40” 20 5/8” 18 5/6” 1/2”

(1015mm) (523mm) (474mm) (13mm)

Step 1

Locating the

Fireplace

The diagram below shows space and clearance

requirements for locating a fireplace within a room.

Model A B C D*

CFX-DIAMOND 42 7/16” 38 1/2” 21 3/4” 5 9/16”

(1078mm) (978mm) (552mm) (141mm)

Figure 3. FramingDimensions

CAUTION

INTERIOR

WALL

CONSTRUCT PLATFORM

WITH 2 X 4 CONSTRUCTION

OR HEAVIER (REQUIRED)

FRONT VIEW SIDE VIE

* Minimum dimension REQUIRED

WARNING: THECFX-DIAMOND REQUIRES

AN ELEVATED PLATFORM CONSTRUC-

TION TO ACCOMMODATE THE DIAMOND

SHAPED SURROUND WHICH IS LARGER

THAN THE FIREPLACE (SEE FIGURE 1)

Minimum Clearances from the Vent Pipe to Combustible Materials

For Vertical

For Horizontal Sections Sections AtWallFirestops

Top Bottom Sides Top Bottom Sides

3 inches* 1 inch 1 inch 1 inch 2-1/2 inches 1/2 inch 1 inch

(75 mm) (25 mm) (25 mm) (25 mm) (63.7 mm) (13 mm) (25 mm)

For minimum clearances, see the direct vent

termination clearance diagrams on pages 25 and

27 in this section.

Additional clearance and/or installation of a heat

shield is required above the first 90° elbow. See

page 19 of the Installers Guide.

Step 2

Framing the

Fireplace

Fireplace framing can be built before or after the

fireplace is set in place. Framing should be

positioned to accommodate wall coverings and

fireplace facing material. The diagram below shows

framing reference dimensions.

MEASURE FIREPLACE DIMENSIONS, AND

VERIFY FRAMING METHODS AND WALL

COVERING DETAILS BEFORE FRAMING

CONSTRUCTION BEGINS.

Vent system components

Vent system

termination kits

Figure 4. Vent Components and Terminations

Step 3

Installing the

Vent System

A. VentSystem Approvals

This model is approved to use D-Series components

and terminations. Approved vent system components

are labeled for identification. NO OTHER VENTING

SYSTEM OR COMPONENTS MAY BE USED.

Detailed installation instructions are included with each

vent termination kit and should be used in conjunction

with this Installers Guide. The drawing below shows

vent system components and terminations.

The flame and ember appearance may vary based on

thetypeof fuelburnedandthe venting configurationused.

Identifying Vent Components

The vent systems installed on this gas fireplace may

include one, two, or three 90oelbow assemblies. The

relationships of vertical rise to horizontal run in vent

configurations using 90oelbows MUST BE strictly

adhered to. The rise to run relationship are shown in the

venting drawings and tables. Refer to the diagrams on

the next several pages.

NOTE: TWO 45OELBOWS MAY BE USED IN PLACE

OF ONE 90OELBOW. RISE TO RUN RATIOS IN

THE VENT SYSTEM MUST BE FOLLOWED IF 45O

ELBOWS ARE USED.

DVK-TVCD

DVK-01TRD

DVK-01D

VERTICAL

TERMINATION

HORIZONTAL

TERMINATION

WALL FIRESTOP

90 DEGREE ELBOW CEILING FIRESTOP

WALL BRACKET

PIPE LENGTH

HORIZONTAL PIPE SUPPORT

ROOF FLASHING

STORM COLLAR

HEAT SHIELD

Tabla de contenidos

Otros manuales de Chimenea de interior de Heat-N-Glo

Heat-N-Glo

Heat-N-Glo AT-Supreme-C Instrucciones de montaje

Heat-N-Glo

Heat-N-Glo CFX-36T Manual de usuario

Heat-N-Glo

Heat-N-Glo ENERGY MASTER EM-415R Manual

Heat-N-Glo

Heat-N-Glo SL-550TRS-AUC Manual de usuario

Heat-N-Glo

Heat-N-Glo Gas Fireplace Manual de usuario

Heat-N-Glo

Heat-N-Glo CFX-ZC Instrucciones de montaje

Heat-N-Glo

Heat-N-Glo CFX-DA Instrucciones de montaje

Heat-N-Glo

Heat-N-Glo Pier-TRC Instrucciones de montaje

Heat-N-Glo

Heat-N-Glo ST-38GTV Instrucciones de montaje

Heat-N-Glo

Heat-N-Glo BAY-INS Instrucciones de montaje

Heat-N-Glo

Heat-N-Glo Pier-38HV Instrucciones de montaje

Heat-N-Glo

Heat-N-Glo 8000TVC Instrucciones de montaje

Heat-N-Glo

Heat-N-Glo 7000TR Instrucciones de montaje

Heat-N-Glo

Heat-N-Glo Grand-50-D Manual de usuario

Heat-N-Glo

Heat-N-Glo SL-950TR Instrucciones de montaje

Heat-N-Glo

Heat-N-Glo 6000 GDVFL Instrucciones de montaje

Heat-N-Glo

Heat-N-Glo SL-Insert Manual de usuario

Heat-N-Glo

Heat-N-Glo 6000TRS-AU Manual de usuario

Heat-N-Glo

Heat-N-Glo GRAND-50 Instrucciones de montaje

Heat-N-Glo

Heat-N-Glo BAYFYRE-TRS Instrucciones de montaje

Heat-N-Glo

Heat-N-Glo BE-41 Instrucciones de montaje

Heat-N-Glo

Heat-N-Glo Pier-PV-IPI Instrucciones de montaje

Heat-N-Glo

Heat-N-Glo SL-550TV-C Instrucciones de montaje

Heat-N-Glo

Heat-N-Glo SL-36 Instrucciones de montaje

Manuales populares de Chimenea de interior de otras marcas

Brigantia

Brigantia 35-DVRS31N-2 Manual del propietario

Nordpeis

Nordpeis Bergen Manual de usuario

Superior

Superior BCT2536TMN Manual de usuario

Quadra-Fire

Quadra-Fire 5100I-GD-B Manual de usuario

Renaissance

Renaissance RUMFORD 1000 Manual de usuario

Lacunza

Lacunza IV-800 Manual de usuario

Baxi

Baxi 940 Instrucciones de uso

Dru

Dru Maestro 60/2 Tall RCH Manual de usuario

Diamond Fireglass

Diamond Fireglass SS-O22 Manual de usuario

HearthStone

HearthStone Windsor Bay 8830 Manual de programación

Napoleon

Napoleon ASCENT B42 Manual de usuario

Enviro

Enviro E33GI Manual de usuario

Smeg

Smeg L30 FABE Instrucciones de montaje

KEDDY

KEDDY K700 Manual de usuario

Godin

Godin 3451 Manual de usuario

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manual de usuario

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manual de usuario

Desa

Desa CCFPDFT Manual de operación