Heat-N-Glo BAY-INS Instrucciones de montaje

- Do not store or use gasoline or other

flammable vapors and liquids in the

vicinity of this or any other appliance.

-What to do if you smell gas

• Do not try to light any appliance.

• Do not touch any electrical switch.

• Do not use any phone in your building.

• Immediately call your gas supplier from

aneighbor'sphone.Followthegas

supplier'sinstructions.

• If you cannot reach your gas supplier,

call the fire department.

- Installation and service must be

performedbya qualified installer,

service agency, or the gas supplier.

Heat-N-Glo Fireplace

Model:

BAY-INS

Underwriters

Laboratories Listed

Installers Guide

WARNING: IMPROPER INSTALLATION,

ADJUSTMENT, ALTERATION, SERVICE

OR MAINTENANCE CAN CAUSE IN-

JURY OR PROPERTY DAMAGE. REFER

TO THIS MANUAL. FOR ASSISTANCE

OR ADDITIONAL INFORMATION CON-

SULT A QUALIFIED INSTALLER, SER-

VICE AGENGY, OR THE GAS SUPPLIER.

099-986-A 11/98

READ THIS MANUAL BEFORE INSTALLING

OR OPERATING THIS APPLIANCE. THIS

INSTALLERS GUIDE

MUST BE LEFT WITH

APPLIANCE FOR FUTURE REFERENCE.

1. This appliance may be installed in an

aftermarket,permanentlylocated,

manufactured(mobile)home,where

not prohibited by local codes.

2. Thisappliance isonlyforuse with the type

ofgas indicatedontheratingplate.This

applianceisnotconvertiblefor use with

othergases,unless a certifiedkit is used.

WARNING IF THE INFORMATION

IN THESE INSTRUCTIONS IS NOT

FOLLOWED EXACTLY, A FIRE OR

EXPLOSION MAYRESULT CAUSING

PROPERTY DAMAGE, PERSONAL

INJURY, OR LOSS OF LIFE.

Please contact your Heat-N-Glo dealer for any

questions or concerns. For the number of your nearest

Heat-N-Glo dealer, please call 612-890-8367.

Heat-N-Glo, a division of Hearth Technologies Inc.

6665 West Highway 13, Savage, MN 55378

This product is covered by one or more of the following patents: (United States) 4,112,913; 4,408,594; 4,422,426; 4,424,792; 4,520,791; 4,793,322;

4,852,548; 4,875,464; 5,000,162; 5,016,609; 5,076,254 5,191,877; 5,218,953; 5,328,356; 5,429,495; 5,452,708; 5,542,407; 5,613,487; (Australia)

543790;586383; (Canada) 1,123,296; 1,297,746; 2,195,264; (Mexico) 97-0457; (New Zealand) 200265; or other U.S. and foreign patents pending.

SAFETY AND WARNING INFORMATION

READ

and

UNDERSTAND

all instructions carefully before starting the installation.

FAILURE TO FOLLOW

these installation instructions may result in a possible fire hazard

and will void the warranty.

Prior to the first firing of the fireplace,

READ

the Using Your Fireplace section of the

Owners Guide

DO NOT USE

this appliance if any part has been under water. Immediately

CALL

qualified service technician to inspect the unit and to replace any part of the control

system and any gas control which has been underwater.

THIS UNIT IS NOT FOR USE WITH SOLID FUEL.

Installation and repair should be

PERFORMED

by a qualified service person. The

appliance and venting system should be

INSPECTED

before initial use and at least

annually by a professional service person. More frequent cleaning may be required due

to excessive lint from carpeting, bedding material, etc. It is

IMPERATIVE

that the unit’s

control compartment, burners, and circulating air passageways

BE KEPT CLEAN

provide for adequate combustion and ventilation air.

Always

KEEP

the appliance clear and free from combustible materials, gasoline, and

other flammable vapors and liquids.

NEVER OBSTRUCT

the flow of combustion and ventilation air. Keep the front of the

appliance

CLEAR

of all obstacles and materials for sevicing and proper operations.

Due to the high temperature, the appliance should be

LOCATED

out of traffic areas and

away from furniture and draperies. Clothing or flammable material

SHOULD NOT BE

PLACED

on or near the appliance.

Children and adults should be ALERTED to the hazards of high surface temperature

and should STAY AWAY to avoid burns or clothing ignition. Young children should be

CAREFULLY SUPERVISED when they are in the same room as the appliance.

These units

MUST

use one of the vent systems described in the Installing the Fireplace

section of the

Installers Guide

NO OTHER

vent systems or components

MAY BE USED

This gas fireplace and vent assembly

MUST

be vented directly to the outside and

MUST

NEVER

be attached to a chimney serving a separate solid fuel burning appliance. Each

gas appliance

MUST USE

a separate vent system. Common vent systems are

PROHIBITED

INSPECT

the external vent cap on a regular basis to make sure that no debris is

interfering with the air flow.

The glass door assembly

MUST

be in place and sealed, and the trim door assembly

MUST

be in place on the fireplace before the unit can be placed into safe operation.

DO NOT OPERATE

this appliance with the glass door removed, cracked, or broken.

Replacement of the glass door should be performed by a licensed or qualified service

person.

DO NOT

strike or slam the glass door.

The glass door assembly

SHALL ONLY

be replaced as a complete unit, as supplied by

the gas fireplace manufacturer.

NO SUBSTITUTE

material may be used.

DO NOT USE

abrasive cleaners on the glass door assembly.

DO NOT ATTEMPT

clean the glass door when it is hot.

Turn off the gas before servicing this appliance. It is recommended that a qualified

service technician perform an appliance check-up at the beginning of each heating

season.

Any safety screen or guard removed for servicing must be replaced before operating

this appliance.

Table of

Contents

Safety and Warning Information................... i

Section 1: Approvals and Codes .................1

Approval Listings and Codes ............................. 1

ApplianceCertification.................................... 1

InstallationCodes........................................... 1

HighAltitude Installations ................................ 1

Section 2: Getting Started.............................2

Introducing the Heat-N-Glo Gas Fireplaces........ 2

Pre-installation Preparation ................................ 2

VentingandInstallation ....................................... 3

Section 3: Installing the Fireplace................5

Step 1 Installing the Vent System .................... 5

Vent SystemApprovals......................... 5

Step2 Positioning, Leveling, and

Securing the Fireplace ....................... 10

Step3 The Gas Control Systems.................. 10

Step4 The Gas Supply Line .......................... 11

Step5 Gas Pressure Requirements ............. 12

Step6 Wiring the Fireplace ........................... 12

Step7 Installing Trim, Logs, and

EmberMaterial ................................... 14

Installing the Trim ......................................... 14

Positioning the Logs..................................... 14

Placing the Ember Material .......................... 15

Step8 Before Lighting the Fireplace............. 17

Step9 Lightingthe Fireplace ........................ 17

Afterthe Installation .......................................... 17

Section 4: Maintenance and Servicing ......18

Section 5: Replacement Parts

and Accessories........................20

Replacement Parts .......................................... 20

Accessories ..................................................... 22

Approvals

and Codes

Approval Listings

and Codes Appliance Certification

The Heat-N-Glo fireplace models discussed in this

Installers Guide

have been tested to certification

standards and listed by the applicable laboratories.

CERTIFICATION

MODEL LABORATORY TYPE STANDARD

BAY-INS Underwriters Vented Gas ANSI Z21.88•CSA2.33

Laboratories Fireplace Heaters

Installation Codes

The fireplace installation must conform to local codes. Before installing the

fireplace, consult the local building code agency to ensure that you are in

compliance with all applicable codes, including permits and inspections.

In the absence of local codes, the fireplace installation must conform to the

National Fuel Gas Code ANSI Z223.1 (in the United States) or the CAN/CGA-

B149 Installation Codes (in Canada). The appliance must be electrically

grounded in accordance with local codes or, in the absence of local codes with

the National Electric Code ANSI/NFPA No. 70 (in the United States), or to the

CSA C22.1 Canadian Electric Code (in Canada).

These models may be installed in a bedroom or bed-sitting room in the U.S.A.

and Canada.

High Altitude Installations

U.L. Listed gas fireplaces are tested and approved for elevations from 0 to 2,000

feet in the U. S.A. and are tested and approved for elevations from 0 to 4,500

feet in Canada.

When installing this fireplace at an elevation above 2,000 feet (in the United

States), it may be necessary to decrease the input rating by changing the

existing burner orifice to a smaller size. Input should be reduced four percent

(4%) for each 1,000 feet above sea level, unless the heating value of the gas

has been reduced, in which case this general rule will not apply. To identify the

proper orifice size, check with the local gas utility.

When installing this fireplace at an elevation between 2,000 and 4,500 feet (in

Canada), the input rating must be reduced by ten percent (10%).

When installing this fireplace at an elevation above 4,500 feet (in Canada),

check with local authorities.

Consult your local gas utility for assistance in determining the proper orifice for

your location.

Getting

Started

Introducing the

Heat-N-Glo

Gas Appliances

Heat-N-Glo direct vent gas appliances are designed

to operate with all combustion air siphoned from

outside of the building and all exhaust gases expelled

totheoutside.

The information contained in this

InstallersGuide

unless noted otherwise, applies to all models and gas

control systems.

Gas appliance diagrams, including the dimensions,

are shown in this section.

Pre-installation

Preparation This gas insert and its components are tested and

safe when installed in accordance with this

Installers

Guide

. Report to your dealer any parts damaged in

shipment, particularly the condition of the glass.

Do not install any unit with damaged, incomplete,

or substitute parts.

The vent system components and trim surrounds are

shipped in separate packages. The gas logs are

packaged separately and must be field installed.

Read all of the instructions before starting the

installation. Follow these instructions carefully

during the installation to ensure maximum safety

and benefit. Failure to follow these instructions

will void the owner’s warranty and may present a

fire hazard.

The Heat-N-Glo Warranty will be voided by, and Heat-

N-Glo disclaims any responsibility for, the following

actions:

• Installation of any damaged fireplace or vent sys-

temcomponent.

• Modification of the fireplace or direct vent system.

• Installation other than as instructed by Heat-N-Glo.

• Improper positioning of the gas logs or the glass

door.

• Installation and/or use of any component part not

manufactured and approved by Heat-N-Glo, not

withstanding any independent testing laboratory or

other party approval of such component part or

accessory.

ANY SUCH ACTION MAY POSSIBLY CAUSE A

FIRE HAZARD.

VENTINGAND INSTALLATION

1. Heat -N-Glo gas inserts are designed for recessed installations into solid fuel

Masonry or Factory Built Non Combustible fireplaces that have been installed in

accordance with the National, Provincial, State and local building codes.

2. Minimum fireplace opening requirements are shown in Figure 1 of this instal-

lation manual. The firebrick (refactory) can be removed from a factory built

fireplace in order to gain minimum gas insert opening requirements.

3. To assure top performance, safety and efficiency, inserts must be installed

with an approved flue liner as per CAN/CGA B-149 or National Fuel Code

ANSI Z223 and these instructions.

WARNING

THE SOLID FUEL FIREPLACE HAS BEEN CONVERTED FOR USE

WITH GAS ONLY AND CANNOT BE USED FOR BURNING WOOD

OR SOLID FUELS UNLESS ALL ORIGINAL PARTS HAVE BEEN

REPLACED AND THE FIREPLACE HAS BEEN REAPPROVED BY

THE AUTHORITY HAVING JURISDICTION.

4. The solid fuel fireplace’s flue damper must be fully locked in the open position

or removed for installation.

5. The chimney must be cleaned and in good working order and constructed of

noncombustiblematerials.

6. Make sure that all chimney cleanouts fit properly so air cannot leak into the

chimney.

7. Install the insert without the trim surround and make all gas, venting, and

electrical connections.

WARNING

Under no circumstances cutting of sheet metal surfaces are al-

lowed for installation.

If the factory built fireplace has no gas access holes provided, an

access hole of 1” diameter (25mm) or less may be drilled through

the lower sides or bottom of the combustion chamber in a proper

workmanship like manner.

8. Install decorative trim surround. Please refer to instructions included with the

trim surround.

Ensure there are no obstructions to side air passages of decorative

trim once installed on insert.

GAS VALVE AND PIEZO

(BEHIND GRILL)

LABELS

(BEHIND GRILL) FAN SPEED CONTROL

(BEHIND LOWER GRILL)

EXHAUST

STARTING

COLLAR

INLET AIR

STARTING

COLLAR

TRIM

DOOR

GLASS

DOOR

SURROUND

(SHOWN INSTALLED)

ROTARY

ON/OFF SWITCH

TOPVIEW

15 1/2 INCHES

27 3/4 INCHES

MINIMUM FIREPLACE SIZE

FRONTWIDTH : 27 3/4” (705mm)

REARWIDTH : 15 1/2” (394mm)

DEPTH : 9” (229mm)

HEIGHT : 22” (559mm)

Figure 1. Diagram of the BAY-INS

When planning a fireplace insert installation, it’s necessary to determine:

•The vent system configuration to be used.

•Gas supply piping.

•Whether optional accessories—devices such as a wall switch, or remote

control—are desired.

Installing

the Insert

Step 1

Installing the

Vent System

Vent System Installation Precautions

Before starting installation of vent kits, the installer

should read these instructions and the Vent Kit

Instructions to ensure that a proper vent installation is

completed.

Consult your local Building Codes before beginning

theInstallation.

WARNING

THIS GAS INSERT AND VENT

ASSEMBLY MUST BE VENTED

DIRECTLY TO THE OUTSIDE AND

MUST NEVER BE ATTACHED TO A

CHIMNEY SERVING A SEPARATE

SOLID FUEL BURNING APPLIANCE.

EACH GAS APPLIANCE MUST USE A

SEPARATE VENT SYSTEM. COMMON

VENT SYSTEMS ARE PROHIBITED.

Vent System Approvals

Table 1 and Figure 3 through 5 shows the vent

termination caps and systems approved for the use

with these models. Approved vent system

terminationsare labeledfor identification. 3-inch

diameter listed flexible aluminum or stainless steel gas

vent is used for both the incoming combustion air and

exhaust vent pipes. NO OTHER VENTING

SYSTEMS OR COMPONENTS MAY BE USED.

Detailed installation instructions are included with

each vent termination kit and should be used in

conjunction with this manual.

Horizontal Venting

The vent system on this model CANNOT be

terminatedhorizontally.

Vertical Venting

The vent pipes MUST be connected to the proper

collars on the unit AND the exhaust vent pipe MUST

be connected to the termination cap or the unit will not

operate. The combustion air vent pipe CAN be

connected to the termination cap or it can terminate

insidethechimney. Thebottomopeningofthe

chimney must be sealed around the vent pipes if the

combustion air vent is NOT connected to the

termination cap. See Figures 3, 4 and 5.

NOTE: The minimum vertical rise (exhaust vent) is 14

feet and the maximum vertical rise is 40 feet. These

dimensions are measured from the starting collars of

the unit to the end of the last section of vent pipe. See

dimensionV in Figure 3.

A vertical vent termination system installed on this

model will include one (1) length of 3-inch flexible

vent pipe for the combustion air, one (1) pipe-to-

cap adaptor, one (1) length of 3 inch flexible vent

pipe for exhaust, and one (1) SLK-991DA or SLK-

980D Vertical termination Cap.

CAUTION

NOTE: The damper of the masonry chimney may

need to be removed to allow installation of the flexible-

vent pipe.

This fireplace has been altered to accommodate an

insert and should be inspected by a qualified person

prior to re-use as a conventional fireplace.

NOTE: The above label, located in the instruction

package, must be affixed to the existing fireplace prior

toinstallationofModel BAY-INS.

For zero clearance, factory built woodburning

fireplaces, the use of kit LINK-ZC-ADP, in place of the

standard square flashing, will allow you to mount the

adaptor and cap on metal pipe. Additionally, the use of

kit FLASH-DAMP will seal off the damper opening

when terminating the inlet air vent pipe just above the

damper. These two kits are recommended for zero

clearance, factory built woodburning fireplaces.

Connecting the Vent Pipe

Install the 3-inch flexible vent pipes down through the

chimney. Attach and secure the bottom ends of the

flex pipes to the starting collars on the unit with 3

sheetmetal screws on each collar. Slide the gas insert

into place, and position any excess flex vent pipe back

up into the chimney.

Attach the pipe-to-cap adaptor to the termination

cap and the top of the flexible vent pipe and set the

cap in place at the top of the chimney. See Figures

3, 4 and 5.

TO AVOID DOWNDRAFTS AND/OR COLD AIR

PROBLEMS, IT IS RECOMMENDED TO SEAL

OFF THE AREA BETWEEN THE TERMINATION

CAP AND THE TOP OF THE SOLID-FUEL

CHIMNEY OPENING INTO WHICH THE VENT

CAP HAS BEEN INSTALLED.

When using the LINK-DV4-30 vent system, it is

required to seal around the flexible vent pipes in the

damper area. See Figure 3. Use fiberglass insulation

or other suitable non-combustible material.

VENT SYSTEM APPROVALS

BAY-INS LINK-DV30

LINK-DV4-30

TABLE 1

Termination Cap

WARNING

MAJOR U.S. BUILDING CODES

SPECIFY MINIMUM CHIMNEY AND/OR

VENT HEIGHT ABOVE THE ROOF TOP.

THESE MINIMUM HEIGHTS ARE

NECESSARY IN THE INTEREST OF

SAFETY. FIGURE 2 SHOWS MINIMUM

HEIGHTS, PROVIDED THE

TERMINATION CAP IS AT LEAST

2-FEET FROM A VERTICAL WALL AND

2-FEET BELOW A HORIZONTAL

OVERHANG.

NOTE: This also pertains to vertical vent systems

installedontheoutsideof the building.

Roof Pitch H (min.) ft.

flatto 6/12 1.0

6/12 to 7/12 1.25

over 7/12 to 8/12 1.5

over 8/12 to 9/12 2.0

over 9/12 to 10/12 2.5

over 10/12 to 11/12 3.25

over 11/12 to 12/12 4.0

over 12/12 to 14/12 5.0

over 14/12 to 16/12 6.0

over 16/12 to 18/12 7.0

over 18/12 to 20/12 7.5

over 20/12 to 21/12 8.0

Figure 2. Minimum Height from Roof to Lowest

Discharge Opening

Tabla de contenidos

Otros manuales de Chimenea de interior de Heat-N-Glo

Heat-N-Glo

Heat-N-Glo SL-550TV Instrucciones de montaje

Heat-N-Glo

Heat-N-Glo SL-3000 Manual de usuario

Heat-N-Glo

Heat-N-Glo CFX-TV36B Instrucciones de montaje

Heat-N-Glo

Heat-N-Glo ST-38GTV Instrucciones de montaje

Heat-N-Glo

Heat-N-Glo 7000XLS Instrucciones de montaje

Heat-N-Glo

Heat-N-Glo SL-350TV Instrucciones de montaje

Heat-N-Glo

Heat-N-Glo Pier-TRC Instrucciones de montaje

Heat-N-Glo

Heat-N-Glo 8000 DVTFL Instrucciones de montaje

Heat-N-Glo

Heat-N-Glo 6000DVT Manual de usuario

Heat-N-Glo

Heat-N-Glo CFX-DIAMOND Instrucciones de montaje

Heat-N-Glo

Heat-N-Glo BE-41 Instrucciones de montaje

Heat-N-Glo

Heat-N-Glo SL-350DVT Instrucciones de montaje

Heat-N-Glo

Heat-N-Glo 6000CAMP Instrucciones de montaje

Heat-N-Glo

Heat-N-Glo HST38 Manual

Heat-N-Glo

Heat-N-Glo 6000 GDVFL Instrucciones de montaje

Heat-N-Glo

Heat-N-Glo WS-150 Instrucciones de montaje

Heat-N-Glo

Heat-N-Glo SL-950TR Instrucciones de montaje

Heat-N-Glo

Heat-N-Glo SL-36 Instrucciones de montaje

Heat-N-Glo

Heat-N-Glo CBS-41 Manual de usuario

Heat-N-Glo

Heat-N-Glo SL-950TR-C Instrucciones de montaje

Heat-N-Glo

Heat-N-Glo 6000FLS Manual de usuario

Heat-N-Glo

Heat-N-Glo 7000XLT Instrucciones de montaje

Heat-N-Glo

Heat-N-Glo 8000TV Manual de usuario

Heat-N-Glo

Heat-N-Glo GRAND-50 Instrucciones de montaje

Manuales populares de Chimenea de interior de otras marcas

Brigantia

Brigantia 35-DVRS31N-2 Manual del propietario

Nordpeis

Nordpeis Bergen Manual de usuario

Superior

Superior BCT2536TMN Manual de usuario

Quadra-Fire

Quadra-Fire 5100I-GD-B Manual de usuario

Renaissance

Renaissance RUMFORD 1000 Manual de usuario

Lacunza

Lacunza IV-800 Manual de usuario

Baxi

Baxi 940 Instrucciones de uso

Dru

Dru Maestro 60/2 Tall RCH Manual de usuario

Diamond Fireglass

Diamond Fireglass SS-O22 Manual de usuario

HearthStone

HearthStone Windsor Bay 8830 Manual de programación

Napoleon

Napoleon ASCENT B42 Manual de usuario

Enviro

Enviro E33GI Manual de usuario

Smeg

Smeg L30 FABE Instrucciones de montaje

KEDDY

KEDDY K700 Manual de usuario

Godin

Godin 3451 Manual de usuario

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manual de usuario

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manual de usuario

Desa

Desa CCFPDFT Manual de operación