HeartSine Samaritan SAM 450P Manual de usuario

HeartSine samaritan®PAD

SAM 450P Trainer

User Manual

model TRN-450-1

2 heartsine.com

Contents

Contents 2

Introduction 3

Preparing the HeartSine samaritan PAD 450P Trainer for use 4

Turning the HeartSine samaritan PAD 450P Trainer on and o 4

HeartSine samaritan PAD 450P Trainer 5

Managing the electrodes 6

Using the electrodes 6

Rewinding the electrodes aer use 6

The remote control 7

Pre-programmed training scenarios 8

Manual control of the HeartSine samaritan PAD 450P Trainer 10

CPR Rate Advisor™training module 11

HeartSine samaritan PAD 450P Trainer with CPR Rate Advisor, SAM 450P 11

CPR Rate Advisor training 11

Compressions 12

Maintenance 14

HeartSine samaritan PAD 450P Trainer battery management 14

Charging and recharging the HeartSine samaritan PAD 450P Trainer 14

Remote control batteries 15

HeartSine samaritan PAD 450P Trainer Conguration Tool 15

CPR Guidelines 2015 16

Disposal instructions 17

Warranty exclusion 17

HeartSine samaritan PAD 450P Trainer User Manual 3

This User Manual provides instructions on how to operate the HeartSine samaritan PAD 450P Trainer.

The HeartSine samaritan PAD 450P Trainer is a non-medical device intended to be used for the training of emergency

responders in the proper use of the HeartSine samaritan PAD 450P (SAM 450P) automated external debrillator. The

HeartSine samaritan PAD 450P Trainer has no therapeutic capabilities and must not be used in real life rescue situations.

IMPORTANT: In order to avoid confusion in the event of a real life rescue, do not store or leave the HeartSine

samaritan PAD 450P Trainer near the HeartSine samaritan PAD 450P automated external debrillator.

To allow quick and easy identication, the HeartSine samaritan PAD 450P Trainer incorporates a yellow front user interface

membrane whereas the SAM 450P automated external debrillator has a navy blue/black front membrane.

HeartSine recommends that responders who may use one of its debrillators should be trained in Cardiopulmonary

Resuscitation with debrillator use (CPR-D). The HeartSine samaritan PAD 450P Trainer is intended to be used by approved

CPR-D training providers for this purpose.

The HeartSine samaritan PAD 450P Trainer is factory congured to operate in accordance with the joint American Heart

Association/European Resuscitation Council (AHA/ERC) 2015 guidelines for CPR. The device comes with six pre-programmed

scenarios based on these guidelines.

Should the CPR guidelines change, soware will be available to upgrade the HeartSine samaritan PAD 450P Trainer to comply.

Please contact your HeartSine authorized distributor or HeartSine Technologies directly.

Once turned on the HeartSine samaritan PAD 450P Trainer will play audible voice prompts with accompanying visual

indicators. The HeartSine samaritan PAD 450P Trainer may also be controlled using the accompanying remote control

included with the device.

Please contact your HeartSine authorized distributor for a list of replacement accessories.

Introduction

4 heartsine.com

Preparing the HeartSine samaritan PAD 450P Trainer for use

1) Ensure that the HeartSine samaritan PAD 450P Trainer is fully charged (see the Maintenance section of this manual).

2) Place the HeartSine samaritan PAD 450P Trainer and the Trainer-Pak™on a at surface. Push the Trainer-Pak into the

opening of the HeartSine samaritan PAD 450P Trainer and listen for a “click” sound to ensure that it is properly inserted.

3) Place the batteries supplied with your HeartSine samaritan PAD 450P Trainer into the remote control.

Do not press any buttons while inserting the remote control batteries as this will reset the

remote control ID.

4) Press the On/O button on the HeartSine samaritan PAD 450P Trainer and listen to the voice prompts to ensure that the

unit is functioning.

If the HeartSine samaritan PAD 450P Trainer has insucient charge, it will not function correctly. When switched on, the

Status Indicator will ash red to indicate that charging is required. If the battery is fully depleted the device will not power

on at all. For full charging instructions see the Maintenance section of this manual.

Turning the HeartSine samaritan PAD 450P Trainer on and o

To turn on the HeartSine samaritan PAD 450P Trainer, press the green On/O button.

By default the HeartSine samaritan PAD 450P Trainer will function in the last scenario setting used.

To turn o the HeartSine samaritan PAD 450P Trainer, press the On/O button again.

Once the HeartSine samaritan PAD 450P Trainer has been turned on, it may be turned o using the accompanying remote

control. To turn o the HeartSine samaritan PAD 450P Trainer, press the red O button on the remote control.

When turned on, the HeartSine samaritan PAD 450P Trainer will automatically turn o aer een minutes if the device is

not being used.

HeartSine samaritan PAD 450P Trainer User Manual 5

A. Data port -

The data port connects the HeartSine samaritan PAD 450P Trainer to a PC via the USB data cable. When the HeartSine samaritan

PAD 450P Trainer is connected, the training provider can change settings, such as training scenarios (see page 8 for training scenarios).

B. Battery charge status LED - The battery charge status LED ashes red when the HeartSine samaritan PAD 450P Trainer needs to be charged,

becomes a steady red when charging and turns o when fully charged.

C. Status indicator -

Flashing green when in use; HeartSine samaritan PAD 450P Trainer is ready for use, Flashing red when in use; HeartSine

samaritan PAD 450P Trainer requires charging.

D. Shock button - Press this button to simulate delivery of a therapeutic shock.

E. Do not touch indicator - Do not touch the patient when the action arrows around this icon are ashing. The SAM 450P may be analyzing the

patient’s heart rhythm or preparing to deliver a shock.

F. Speaker - The speaker plays recorded voice prompts and gives instructions to the trainee.

G. Trainer-Pak cartridge - The Trainer-Pak cartridge houses the pads. Pull the green tab to access the pads.

H. On/O button - Press this button to turn the device on and o. (If pressed while a shock is advised, a warning is issued “Warning, O

button pressed”; the device will not power o unless you press the button again within three seconds.)

I. Safe to touch indicator - It is safe to touch the patient when the action arrows around this icon are ashing. You may perform CPR or check

the patient.

J. CPR Rate Advisor - This is an array of lights which provide a graduated indication of the speed of the CPR compressions. When green lights

illuminate the compressions are within the correct rate range.

K. Pads placement indicator - The action arrows around this icon will ash to instruct the user that the SAM 450P pads should be attached to

the patient as indicated.

L. Action arrows - The action arrows around an icon will ash to indicate the actions that the user should perform.

BOn/O

button

Pads

placement

indicator

Safe to touch

indicator

Status

indicator

Preparing the HeartSine samaritan PAD 450P Trainer for use

Action

arrows

Do not

touch

indicator

Shock

button

CPR Rate

Advisor

6 heartsine.com

Managing the electrodes

Using the electrodes

The training scenarios include audible prompts to remove the electrodes from the Trainer-Pak and to position the electrode

pads as indicated. Follow the steps below when prompted to do so.

1) Pull the green tab to open the HeartSine samaritan PAD 450P Trainer Trainer-Pak cartridge and fully extend the electrode

cables.

2) Peel the electrode pads from their protective liners.

3) Position the electrode pads as indicated by the Pads Placement Indicator; sternum and apex electrode pads are clearly

identied on their respective pads.

4) Press the pads rmly to ensure that proper contact is made.

Rewinding the electrodes aer use

1) Re-attach the protective liners to the electrode pads, or replace with new pads.

2) Fold the pads together so that the liner is on the outside.

3) Let the electrodes hang from the device and use the handle in the blue coil mechanism to fully rewind the electrodes:

4) Place the pads on top of the Trainer-Pak cartridge, ensuring that the wires are beneath the pads.

5) Close the Trainer-Pak cartridge by sliding the yellow tray into place.

A Coil Mechanism

B Coil Handle

HeartSine samaritan PAD 450P Trainer User Manual 7

A. Turning o the HeartSine samaritan PAD 450P Trainer - The remote control can be used to turn o the HeartSine samaritan PAD 450P

Trainer. To turn o the HeartSine samaritan PAD 450P Trainer, press the red O button on the remote control.

B. Changing the volume - There are four volume settings available on the HeartSine samaritan PAD 450P Trainer. To increase the volume press

the ‘+’ button and to decrease the volume press the ‘-’ button.

C. Low battery indicator - During use of the remote control, if the battery is low on charge the low battery indicator ashes red each time a

button on the remote is pressed. This alerts the training provider to change the batteries in the remote control

D. Pausing the HeartSine samaritan PAD 450P Trainer - The HeartSine samaritan PAD 450P Trainer may be paused during training. To pause

the HeartSine samaritan PAD 450P Trainer press the Pause/Play button ( ||/►). The HeartSine samaritan PAD 450P Trainer will remain paused

until the Pause/Play button is pressed again, at which point it will continue to play the scenario selected.

E. ‘No shock advised’ scenario - When the ‘no shock advised’ scenario button is pressed, the HeartSine samaritan PAD 450P Trainer plays the

‘no shock advised’ voice prompt subsequently followed by the rest of the voice prompts in the programmed scenario.

F. ‘Shock required’ scenario - When the ‘shock advised’ scenario button is pressed, the HeartSine samaritan PAD 450P Trainer plays the ‘shock

advised’ voice prompt subsequently followed by the rest of the voice prompts in the programmed scenario.

G. Changing the scenario - The HeartSine samaritan PAD 450P Trainer comes with six preprogrammed training scenarios. (For details of the

scenarios see the training scenarios section of this manual.) The scenario can be changed by pressing the appropriate number button on the

remote control. For instance pressing ‘3’ will select training scenario three. Once the scenario has been changed the device will operate as

detailed in the scenarios section. The device will remain in this scenario until a new scenario is selected.

H. Attach electrode pads - The attach electrode pads button is pressed to simulate a good connection between the pads and the patient.

I. CPR Rate Advisor rate control - One of the three CPR Rate Advisor rate control buttons is pressed to simulate the prompts heard on the AED

to indicate the quality of the CPR rate: “Press faster”, “Press slower” or “ Good speed”.

The remote control

O button

Volume control

Pause/Play button

Scenario selecion

button

8 heartsine.com

Pre-programmed training scenarios

The HeartSine samaritan PAD 450P Trainer has six preprogrammed training scenarios to choose from. All preprogrammed

scenarios are based on AHA/ERC 2015 guidelines. Details of the preprogrammed scenarios are given below.

Scenario 1

1. Setup mode Trainee to “Call for Medical assistance”, “Pull green tab”, etc

2. User intervention Training provider presses the Attach electrode pads button to conrm electrodes placed

3. Monitor mode Trainee hears “Assessing heart rhythm”, “Do not touch the patient”, etc

4. Shock advised Trainee to press the shock button

5. CPR mode Trainee to perform CPR with guidance from prompts

6. Monitor mode Trainee hears “Assessing heart rhythm”, “Do not touch the patient”, etc

7. No shock advised Trainee notied that no shock is advised

8. CPR mode Trainee to perform CPR with guidance from prompts

9. Repeat Trainee to repeat Steps 6 to 8 until ‘On/O’ button is pressed

Scenario 2

1. Setup mode Trainee to “Call for Medical assistance”, “Pull green tab”, etc

2. User intervention Training provider presses the Attach electrode pads button to conrm electrodes placed

3. Monitor mode Trainee hears “Assessing heart rhythm”, “Do not touch the patient”, etc

4. No shock advised Trainee notied that no shock is advised

5. CPR mode Trainee to perform CPR with guidance from prompts

6. Monitor mode Trainee hears “Assessing heart rhythm”, “Do not touch the patient”, etc

7. Shock advised Trainee to press the shock button

8. CPR mode Trainee to perform CPR with guidance from prompts

9. Repeat Trainee to repeat Steps 6 to 8 until ‘On/O’ button is pressed

Scenario 3

1. Electrodes Device assumes the electrodes are already attached

2. Monitor mode Trainee hears “Assessing heart rhythm”, “Do not touch the patient”, etc

3. Check Pads Trainee to check the pad placement.

4. User intervention Training provider presses the Attach electrode pads button to conrm electrodes placed

5. Monitor mode Trainee hears “Assessing heart rhythm”, “Do not touch the patient”, etc

6. Shock advised Trainee to press the shock button

7. CPR mode Trainee to perform CPR with guidance from prompts

8. Monitor mode Trainee hears “Assessing heart rhythm”, “Do not touch the patient”, etc

9. No shock advised Trainee notied that no shock is advised

10. CPR mode Trainee to perform CPR with guidance from prompts

11. Repeat Trainee to repeat Steps 3 to 10 until ‘On/O’ button is pressed

HeartSine samaritan PAD 450P Trainer User Manual 9

Pre-programmed training scenarios

Scenario 4

1. Electrodes Device assumes electrodes are already attached

2. Monitor mode Trainee hears “Assessing heart rhythm”, “Do not touch the patient”, etc

3. Shock advised Trainee to press the shock button

4. CPR mode Trainee to perform CPR with guidance from prompts

5. Monitor mode Trainee hears “Assessing heart rhythm”, “Do not touch the patient”, etc

6. Shock advised Trainee to press the shock button

7. CPR mode Trainee to perform CPR with guidance from prompts

8. Monitor mode Trainee hears “Assessing heart rhythm”, “Do not touch the patient”, etc

9. No shock advised Trainee notied that no shock is advised

10. CPR mode Trainee to perform CPR with guidance from prompts

11. Repeat Trainee to repeat Steps 5 to 10 until ‘On/O’ button is pressed

Scenario 5

Scenario 5 is the same as Scenario 1 with the addition of audible indications of when to perform rescue breaths during CPR mode.

1. Setup mode Trainee to “Call for Medical assistance”, “Pull green tab”, etc

2. User intervention Training provider presses the Attach electrode pads button to conrm electrodes placed

3. Monitor mode Trainee hears “Assessing heart rhythm”, “Do not touch the patient”, etc

4. Shock advised Trainee to press the shock button

5. CPR mode Trainee to perform CPR with guidance from prompts; this includes an audible indication of when to perform

rescue breaths. The metronome changes from a “beep” to a “tick” for the duration of ten compressions.

6. Monitor mode Trainee hears “Assessing heart rhythm”, “Do not touch the patient”, etc

7. No shock advised Trainee notied that no shock is advised

8. CPR mode Trainee to perform CPR with guidance from prompts; this includes an audible indication of when to perform

rescue breaths. The metronome changes from a “beep” to a “tick” for the duration of ten compressions.

9. Repeat Trainee to repeat Steps 6 to 8 until ‘On/O’ button is pressed

Scenario 6

Scenario 6 is the same as Scenario 2 with the addition of audible indications of when to perform rescue breaths during CPR mode.

1. Setup mode Trainee to “Call for Medical assistance”, “Pull green tab”, etc

2. User intervention Training provider presses the Attach electrode pads button to conrm electrodes placed

3. Monitor mode Trainee hears “Assessing heart rhythm”, “Do not touch the patient”, etc

4. No shock advised Trainee notied that no shock is advised

5. CPR mode Trainee to perform CPR with guidance from prompts; this includes an audible indication of when to perform

rescue breaths. The metronome changes from a “beep” to a “tick” for the duration of ten compressions.

6. Monitor mode Trainee hears “Assessing heart rhythm”, “Do not touch the patient”, etc

7. Shock advised Trainee to press the shock button

8. CPR mode Trainee to perform CPR with guidance from prompts; this includes an audible indication of when to perform

rescue breaths. The metronome changes from a “beep” to a “tick” for the duration of ten compressions.

9. Repeat Trainee to repeat Steps 6 to 8 until ‘On/O’ button is pressed

10 heartsine.com

Manual control of the HeartSine samaritan PAD 450P Trainer

The remote control allows training providers to control the scenario manually. When turned on, the HeartSine samaritan

PAD 450P Trainer will operate as described in the training scenarios listed. Training providers can override this by pressing the

‘Shock required’,‘No shock required’ or ‘Attach electrode pads’ button.

Shock required

Pressing the ‘Shock required’ button will cause the HeartSine samaritan PAD 450P Trainer to

override the selected training scenario and simulate a shockable rhythm. Each subsequent

analysis period will advise a shock to be delivered until either the HeartSine samaritan PAD 450P

Trainer is turned o or the ‘No shock required’ button on the remote control is pressed.

No shock required

Pressing the ‘No shock required’ button will cause the HeartSine samaritan PAD 450P Trainer to

override the selected training scenario and simulate a non-shockable rhythm. Each subsequent

analysis period will advise no shock to be delivered until either the HeartSine samaritan PAD 450P

Trainer is turned o or the ‘Shock required’ button on the remote control is pressed.

Attach electrode pads

If the ‘Attach electrode pads’ button is pressed the HeartSine samaritan PAD 450P Trainer

will play the ‘Attach electrode pads’ prompts during the analysis period of operation. The

HeartSine samaritan PAD 450P Trainer will continue to play ‘Attach electrodes pads’ prompts

until the ‘Attach electrode pads’ button is pressed again.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipos educativos de HeartSine

HeartSine

HeartSine samaritan PAD 350P Trainer Manual de usuario

Manuales populares de Equipos educativos de otras marcas

DISCOVER

DISCOVER talking pen Manual de usuario

pitsco

pitsco Smart Buddies 45895 Manual de usuario

RS 3.5 Manual de usuario

Quanser

Quanser QNET 2.0 Manual de usuario

CAE Healthcare

CAE Healthcare METIman Manual de usuario

Turning Technologies

Turning Technologies Pulse Manual de usuario

fischertechnik

fischertechnik STEM Coding Pro Manual de usuario

Experia

Experia IRiS Light Wand Manual de usuario

Pitsco Education

Pitsco Education FLO Manual de usuario

Sphero

Sphero RVR RV01 Manual de usuario

Limbs & Things

Limbs & Things 60905 Manual de usuario

JP TURN Connect T101 Manual de usuario

TruCorp

TruCorp AirSim Advance Manual de usuario

LeapFrog

LeapFrog Mr. Pencil's Scribble, Write & Read Manual de usuario

ScienTECH

ScienTECH 2261 Manual de usuario

Rompa

Rompa 20019 Manual de usuario

Duinotech

Duinotech XC4322 Manual de usuario

Enabling Devices

Enabling Devices Spinning Light Show Manual de usuario

HeartSine samaritan SAM 450P Manual de usuario

Manuales populares de Equipos educativos de otras marcas