HBK Z6 Manual de usuario

ENGLISH DEUTSCH FRANÇAIS

Mounting Instructions

Montageanleitung

Notice de montage

Hottinger Brüel & Kjaer GmbH

Im Tiefen See 45

D-64293 Darmstadt

Tel. +49 6151 803-0

Fax +49 6151 803-9100

[email protected]

www.hbkworld.com

Mat.: 7-2001.5001

DVS: A01027 04 Y00 03

03.2022

Hottinger Brüel & Kjaer GmbH

Subject to modifications.

All product descriptions are for general information

only. They are not to be understood as a guarantee of

quality or durability.

Änderungen vorbehalten.

Alle Angaben beschreiben unsere Produkte in allge

meiner Form. Sie stellen keine Beschaffenheits- oder

Haltbarkeitsgarantie dar.

Sous réserve de modifications.

Les caractéristiques indiquées ne décrivent nos

produits que sous une forme générale. Elles

n'impliquent aucune garantie de qualité ou de

durabilité.

ENGLISH DEUTSCH FRANÇAIS

Mounting Instructions

TABLE OF CONTENTS

1 Safety instructions 4................................................

2 Markings used 6....................................................

2.1 The markings used in this document 6.................................

2.2 Symbols on the device 6.............................................

3 Conditions on site 7.................................................

4 Mechanical installation 8............................................

4.1 Important precautions during installation 8..............................

4.2 Mounting and load application 8.......................................

5 Electrical connection 10..............................................

5.1 Connection in six-wire configuration 10..................................

5.2 Connection in four-wire configuration 10.................................

5.3 Shortening the cable 11...............................................

5.4 Cable extension 11...................................................

5.5 Parallel connection 11................................................

5.6 EMC protection 12...................................................

6 Waste disposal / environmental protection 13...........................

7 Specifications 14....................................................

7.1 Z6FD1 and Z6FC3 14.................................................

7.2 Z6FC3MI, Z6FC4 and Z6FC6 16........................................

7.3 Specifications for all versions 17.......................................

8 Dimensions 18......................................................

8.1 Z6…/5kg …500kg 18................................................

8.2 Z6…/1t 19..........................................................

9 Accessories 20......................................................

9.1 ZPL pendulum bearing, Emax = 5kg …1t 20.............................

9.2 Knuckle eye ZGWR 21................................................

9.3 Force feedback ZRR 22...............................................

9.4 Rubber-metal bearing ZEL 23..........................................

9.5 Cone, conical pan ZK 26...............................................

9.6 Oscillating loading foot ZFP and ZKP 27.................................

9.7 Oscillating loading foot PCX 28.........................................

9.8 Mounting base / mounting kit 29.......................................

SAFETY INSTRUCTIONS

1 SAFETY INSTRUCTIONS

Appropriate use

Transducers of the Z6... type series are designed solely for technical weighing applica

tions within the application limits detailed in the specifications. Any other use is not

appropriate.

Any person instructed to carry out installation, commissioning or operation of the trans

ducer must have read and understood the Mounting Instructions and in particular the

technical safety instructions.

In the interests of safety, the transducer should only be operated by qualified personnel

and as described in the Mounting Instructions. It is also essential to comply with the legal

and safety requirements for the application concerned during use. The same applies to

the use of accessories.

The transducer is not intended for use as a safety component. Please also refer to the

section: "Additional safety precautions". Proper and safe operation requires proper trans

portation, correct storage, siting and mounting, and careful operation.

Operating conditions

Please observe the permissible maximum values stated in the specifications for:

-Limit load

-Limit load at max. eccentricity

-Limit lateral loading

-Breaking loads

-Temperature limits

-Limits of electrical loading capacity

Note, that when several transducers are installed in a scale, there is not always an

even distribution of load on the individual transducers.

The transducers can be used as machine elements. When used in this manner, it must

be noted that, to favor greater sensitivity, the transducer is not designed with the

safety factors usual in mechanical engineering.

The transducer must not be modified from the design or safety engineering point of

view except with our express agreement.

The transducer is maintenance-free.

In accordance with national and local environmental protection and material recovery

and recycling regulations, old transducers that can no longer be used must be dis

posed of separately and not with normal household garbage, see Chapter 6, Page 12.

SAFETY INSTRUCTIONS

Explosion protection version option

Comply with the relevant code of practice during installation.

Comply with the installation conditions cited in the Certificate of Conformity and/or

the Type Certificate.

Qualified personnel

Qualified persons means persons entrusted with the installation, fitting, commissioning

and operation of the product who possess the appropriate qualifications for their func

tion.

This includes people who meet at least one of the three following requirements:

Knowledge of the safety concepts of measurement and automation technology is a

requirement and as project personnel, they must be familiar with these concepts.

As measurement or automation plant operating personnel, they have been instructed

how to handle the machinery. They are familiar with the operation of the equipment

and technologies described in this documentation.

As commissioning engineers or service engineers, they have successfully completed

the training to qualify them to repair the automation systems. They are also autho

rized to activate, ground and label circuits and equipment in accordance with safety

engineering standards.

Additional safety precautions

Additional safety precautions to meet the requirements of the relevant national and local

accident prevention regulations must be taken in plants where malfunctions could cause

major damage, loss of data or even personal injury.

The scope of supply and performance of the transducer covers only a small area of mea

surement technology. Before starting up the transducer in a system, a project planning

and risk analysis must first be implemented, taking into account all the safety aspects of

measurement and automation technology so that residual risks are minimized. This par

ticularly concerns personal and machine protection. The transducers function passively

and cannot implement any (safety-relevant) cutoffs. In the event of a fault, the relevant

precautions must establish safe operating conditions.

General dangers of failing to follow the safety instructions

The transducer corresponds to the state of the art and is failsafe. The transducer may

give rise to residual dangers if it is inappropriately installed or operated.

MARKINGS USED

2 MARKINGS USED

2.1 The markings used in this document

Important instructions for your safety are specifically identified. It is essential to follow

these instructions in order to prevent accidents and damage to property.

Symbol Significance

WARNING This marking warns of a potentially dangerous situ

ation in which failure to comply with safety require

ments can result in death or serious physical injury.

CAUTION This marking warns of a potentially dangerous

situation in which failure to comply with safety

requirements can result in slight or moderate physical

injury.

Notice This marking draws your attention to a situation in

which failure to comply with safety requirements can

lead to damage to property.

Important This marking draws your attention to important in

formation about the product or about handling the

product.

Tip This marking indicates application tips or other

information that is useful to you.

Information This marking draws your attention to information

about the product or about handling the product.

Emphasis

See …

Italics are used to emphasize and highlight text and

identify references to sections, diagrams, or external

documents and files.

2.2 Symbols on the device

CE certification

The CE mark enables the manufacturer to guarantee that the

product complies with the requirements of the relevant EC direc

tives (the Declaration of Conformity can be found on the HBM

website (www.hbm.com) under HBMdoc).

CONDITIONS ON SITE

3 CONDITIONS ON SITE

Series Z6... load cells are hermetically encapsulated and are therefore not at all sensitive

to the influence of moisture and humidity. The transducers achieve protection class IP68

(test conditions: 100 hours under 1 m water column) as per DIN EN60529. Nevertheless,

the load cells must be protected against constant humidity and moisture.

Protection against corrosion

The load cell must be protected against chemicals that could attack the transducer body

steel, or the cable.

Notice

Acids and all substances that release ions also attack stainless steels and their welded

seams.

Should there be any corrosion, this could cause the transducer to fail. If this is the case,

you must provide appropriate means of protection.

Explosion protection version option

The ambient temperature range specified on the transducer must not be exceeded.

Deposits

Dust, dirt and other foreign matter must not be allowed to accumulate sufficiently to

divert some of the measuring force onto the housing, thus invalidating the measured

value (force shunt).

MECHANICAL INSTALLATION

4 MECHANICAL INSTALLATION

4.1 Important precautions during installation

Handle the transducer with care.

The bellows material is very thin and can therefore be easily damaged.

Welding currents must not be allowed to flow over the transducer. If there is a risk

that this might happen, you must provide a suitable low-ohm connection to electrically

bypass the transducer. HBM, for example, provides the highly flexible EEK ground

cable, which can be screwed on above and below the transducer.

Make sure that the transducer cannot be overloaded.

WARNING

There is a danger of the transducer breaking if it is overloaded. This can cause danger for

the operating personnel of the system in which the transducer is installed.

Implement appropriate safety measures to avoid overloads or to protect against the

resulting dangers.

Notice

Load cells are precision measuring elements and need to be handled carefully. Dropping or

knocking the transducer may cause permanent damage. Make sure that the transducer

cannot be overloaded, including while it is being mounted.

4.2 Mounting and load application

Attach the load cells at the mounting holes and apply load to the other end. The screws

and tightening torques to be used are given in the following table:

Maximum

capacities

Thread Min. property class Tightening torque 1)

5 - 200 kg M8 10.9 34 N⋅m

500 kg M10 12.9 76 N⋅m

1 t M12 10.9 115 N⋅m

1) Recommendedvalue for the specified property class. Please comply with the screw manufacturer's

instructions with regard to screw dimensions.

MECHANICAL INSTALLATION

Important

Load must not be applied to the side where the cable connection is located, as this would

cause a force shunt.

The load must act as accurately as possible in the direction of measurement. Torsional

moments, eccentric loads and lateral or side forces cause measurement errors and can

permanently damage the load cell. Catch such interference effects, e.g. using lateral stay

bars or guide rollers, but ensure that these elements do not absorb any load or force

components in the direction of measurement (force shunt which will in turn lead to mea

surement errors).

To minimize error effects from load application, HBM offers different load application

elements, according to the mounting conditions:

Pendulum bearing ZPL

Knuckle eyes ZGWR

Force feedback ZRR (for maximum capacities 5kg …200kg)

Rubber-metal bearing ZEL

Cone/conical pan ZK

Oscillating loading foot PCX (for maximum capacities 5kg …500kg)

Oscillating loading foot ZFP (for maximum capacities 5kg …200kg)

Oscillating loading foot ZKP (for maximum capacities 5kg …200kg)

Mounting base / mounting kit ZPU Z6/ZPU/200KG (for maximum capacities 5kg …

200kg)

Z6/ZPU/500KG (for maximum capacity 500 kg)

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Transductor de HBK

HBK

HBK T210 Manual de usuario

HBK

HBK AED 9101D Manual de usuario

HBK

HBK HBM Bruel & Kjaer U10M Manual de usuario

HBK

HBK AED 9101D Manual de usuario

Manuales populares de Transductor de otras marcas

HBM

HBM AD101B Manual de usuario

Camille Bauer

Camille Bauer SINEAX F534 Manual de usuario

Trane

Trane KIT 16724 Instrucciones de montaje

Lumel

Lumel P18 Manual de usuario

B&C Speakers

B&C Speakers DE75PTN Manual de usuario

MAMAC SYSTEMS

MAMAC SYSTEMS PR-243 Manual

Mianyang Weibo Electronic

Mianyang Weibo Electronic WB Series Manual de usuario

ProMinent

ProMinent Dulcometer DMT Manual de usuario

MKS

MKS MicroPirani 925 Series Cómo utilizar

WIKA

WIKA WU-20 Manual de usuario

Alcatel Vacuum Technology

Alcatel Vacuum Technology BARATRON 622A Manual de usuario

Camille Bauer

Camille Bauer SIRAX CH-5610 Manual de usuario

WIKA

WIKA F2802 Manual de usuario

Veris Industries

Veris Industries PW Series Manual de usuario

HBM

HBM TJ1-S6 Manual de usuario

Simrad

Simrad ES120-7C - REV D Guía del usuario

HBM

HBM C18 Manual de usuario

Airmar

Airmar M260 Manual de instrucciones