HAUL MASTER 90018 Instrucciones de montaje

Page 2 For technical questions, please call 1-800-444-3353. Item 90018

Specifications

Load Capacity 1500 lb.

Ramp Length 69"

Ramp Width 45"

Important Safety Information

1. Before use:

a. Read and understand manual.

b. Inspect before every use; do not

use if parts loose or damaged.

c. Turn vehicle’s ignition OFF

and set parking brake.

d. Clean dirt, oil and debris off

ramp(s) and allow ramp(s) to dry.

e. Unfold ramp(s) completely.

f. Set up only on solid,

level, dry surface.

g. Turn ramp(s) so flange end faces

downward. Position ramp(s) so

that tongues fully contact tailgate.

h. Properly connect safety chains.

Load vehicle slowly. Do not

ride vehicle down ramp(s).

2. Do not exceed 500 lb. capacity per

separated panel or 1,500 lb. capacity

evenly distributed across joined ramp.

Be aware of dynamic loading! Sudden

load movement may briefly create

excess load causing product failure.

3. Use safety chains as intended only.

4. Use as intended only.

5. Do not use:

a. as ladder,

b. if tailgate on carrying vehicle

is higher than 34”, or

c. to load vehicle with wheel

width wider than ramp.

6. Ground contact. Use your Ramps

on a solid, level, flat, dry surface.

Make sure the Tongue edge fully

contacts the tailgate of the vehicle.

7. Clean Ramps. Prior to each use,

clean dirt, oil, or any debris off ramps.

8. The Ramps are not designed

to be used separately.

9. Be aware of dynamic loading!

Sudden load movement may

briefly create excess load

causing product failure.

10. This product is not a toy. Do not allow

children to play with or near this item.

11. Maintain product labels and

nameplates. These carry

important safety information.

If unreadable or missing, contact

Harbor Freight Tools for a replacement.

12. Load vehicle slowly. Do not ride a

vehicle up or down the load ramp.

Page 3For technical questions, please call 1-800-444-3353.Item 90018

13. All persons not involved in the

loading process must stand

clear of the loading ramps. Keep

children away. Children must not

be allowed in the work area.

14. Check maximum tailgate weight

capacity. Do not exceed tailgate

capacity if less than 1,000 lb.

15. Avoid working alone. If an accident

happens, an assistant can bring help.

16. Keep work area clean and well lit.

Cluttered and dark areas invite injuries.

17. Store idle equipment. When

not in use, store ramps in a

dry location to inhibit rust.

18. Dress properly. Do not wear loose

clothing or jewelry. Protective clothes

and nonskid footwear are recommended

when working. Wear restrictive hair

covering to contain long hair.

19. Wear ANSI-approved impact safety

goggles, a safety helmet, and heavy-

duty work gloves when loading,

unloading or handling ramps.

20. Keep proper footing and balance

when loading or unloading.

21. Do not modify this product.

22. Stay alert. Watch what you are

doing, use common sense. Do not

use any ramp when you are tired.

23. Check for damaged parts. Before

using any ramp, any part that appears

damaged should be carefully checked

to determine that it will perform its

intended function. Check for any

broken parts or mounting fixtures and

any other condition that may affect

proper operation. Any part that is

damaged should be properly repaired

or replaced by a qualified technician.

24. Replacement parts and

accessories. When servicing, use

only identical replacement parts.

Use of any other parts will void the

warranty. Only use accessories

intended for use with this ramp.

25. Do not use ramp if under the

influence of alcohol or drugs. Read

warning labels on prescriptions to

determine if your judgment or reflexes

are impaired while taking drugs. If there

is any doubt, do not use the ramp.

26. The warnings, cautions, and instructions

discussed in this instruction manual

cannot cover all possible conditions

and situations that may occur. It must

be understood by the operator that

common sense and caution are factors

which cannot be built into this product,

but must be supplied by the operator.

SAVE THESE INSTRUCTIONS.

Page 4 For technical questions, please call 1-800-444-3353. Item 90018

Setup and Operation Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the

beginning of this document including all text under subheadings therein

before set up or use of this product.

TO PREVENT SERIOUS INJURY: Make sure the vehicle is turned off and in

gear or park, with the emergency brake engaged and the wheels blocked.

Make sure the Ramp is completely open and the securing chains and hooks are

secured onto the vehicle. Make sure the Ramp is clean and dry before loading.

Setup

Safety Chain

Hinges

Tri-fold

Ramp

Tongues

Figure A: Components

When folded, the Ramp will be

wrapped in the Safety Chains and

Hooks. Release the hooks and

unfold the Ramp completely.

2. Make sure the tailgate the ramp

will sit on is dry and clean.

3. Sit the Tongues (angled lips) of the

Ramp on the tailgate. Stretch the

Safety Chain on each side of the Ramp

up into the inside of the truck bed.

4. Attach the hook on each Safety

Chain to a secure attachment point

on the inside of the truck bed.

WARNING! Safety chains must be

connected to secure attachment

points able to withstand the pulling

force of loading. They must also be

taut enough to prevent the ramp from

coming off the vehicle being loaded.

5. Pull the loading ramp back until

the chains are tight. If most of the

edge or the entire edge of the ramp

is off of the edge of the vehicle

the chains need to be adjusted or

shorter chains must be used.

Chain Adjustment

1. Remove the bolt and washer that

hold the safety chain to the ramp.

2. Reinsert the bolt through a link that

will shorten the chain so the loading

ramp can not be pulled backwards

more than an inch or two.

3. Make sure that the bolt is properly

tightened and the washer prevents the

bolt from slipping through the chain link.

4. Adjust the other chain to equal length.

Page 5For technical questions, please call 1-800-444-3353.Item 90018

ATV Loading and Unloading

• Do not use this ramp to load

or unload any vehicle that

weighs more than 1500 lb.

• Do not use this ramp to load

or unload any vehicle that

is wider than the ramp.

• Do not use this ramp to load

or unload any vehicle that is

carrying gear on its racks.

• Do not use this ramp if the

tailgate on the vehicle being

loaded or unloaded is higher than

half the ramp’s length (34").

WARNING: Be aware of dynamic loading!

Sudden load movement may briefly create

excess load causing the Ramp to fail.

WARNING! All persons not involved in

the process must stand clear of the Ramp

and truck. Make sure no pets are nearby.

Loading Using a Winch (not included)

1. The winch and mounting/

connection points must all have

appropriate capacity to pull the

ATV up the ramp safely.

2. ATV Mounted Winch Setup: Unwind

cable from the winch and attach it to a

secure mounting location on the truck,

at the same height as the winch will

be after the ATV has been loaded.

3. Truck Mounted Winch Setup:

Attach the cable to the bottom

front part of the frame.

4. While operating the winch, stand

back and to the side of the

ATV, with the vehicle between

you and the winch cable.

5. Operate the winch to slowly load

the ATV onto the vehicle.

Unloading

WARNING! Riding an ATV while unloading

is dangerous and should not be attempted.

1. Have an assistant monitor the Ramp

tongue for slippage on the tailgate.

2. Setup the ramp on the truck bed

as explained under operation.

Remove all tie down straps and

securing equipment from the ATV.

WARNING! Be sure the 4-wheel

ATV is centered on ramp.

3. While staying off the ATV, start

the engine, disengage the parking

brake, put the transmission into

reverse, and make sure the wheels

are in a straight line with the ramp.

While holding the brake, position

yourself in front of the ATV.

4. Release the brake and push on the ATV

to get it started down the ramp. Allow

the ATV to roll down naturally, do not

attempt to steer it or apply the brakes.

If it stops while on the ramp, gently

give it throttle to back it off the ramp.

Page 6 For technical questions, please call 1-800-444-3353. Item 90018

Expert Loading Directions

Only for individuals certified by the ASI (ATV Safety Institute)

By using directions in this section, you are agreeing that you are an ASI trained, certied rider

and that you understand that your safety in performing this procedure is

based on your ability to control the vehicle.

1. Have an assistant monitor the Ramp

tongue for slippage on the tailgate.

2. Confirm that the weight of the ATV

and rider combined is still less than

the 1500 lb. capacity of this ramp.

3. While wearing a safety helmet, drive

your ATV onto ramp at less than 1

Mile Per Hour using the lowest gear

possible. Drive up at a slow, steady

speed while leaning forward on the

front pegs to keep proper balance. Try

to avoid bouncing or jerking, because

they will increase stress on the ramp.

WARNING! Be sure the 4-wheeled

ATV is centered on ramp.

4. Once the load is in truck bed,

be sure to set the ATV’s brake &

securely tie down ATV. Remove the

ramp, fold it up and secure it with

the Safety Chains and Hooks.

CAUTION! Contact between the tongue of

the ramp and the tailgate of the vehicle may

result in damage to the vehicle’s body finish.

CAUTION! WHENEVER possible, use

a winch (not included) to load the ATV.

This is the safest way to load an ATV.

Page 7For technical questions, please call 1-800-444-3353.Item 90018

Parts List

Part Description Qty

1 Tri-fold Ramp 1

2 Safety Chain and Hook set 2

3 Hinge 6

Record Serial Number Here:

Note: If product has no serial number, record month and year of purchase instead.

Note: Some parts are listed for illustration purposes only, and

are not available individually as replacement parts.

Maintenance and Servicing

Procedures not specifically explained in this manual must

be performed only by a qualified technician.

TO PREVENT SERIOUS INJURY:

Remove the ramp from the vehicle before performing any maintenance or service.

Do not use damaged equipment. If Ramp is damaged

have the problem corrected before further use.

Cleaning, Maintenance, and Lubrication

1. BEFORE EACH USE, inspect

the general condition of the

Ramp. Check for:

• loose hardware,

• misalignment or binding of parts,

• cracked or broken parts, and

• any other condition that may

affect its safe operation.

2. Clean the ramp after each use.

Make sure any dirt, oil, grease, or

debris are not on the Ramp.

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST IN THIS

DOCUMENT AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR

MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE

OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS

QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/

OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS

SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY

THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR

HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR

ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality

and durability standards, and warrants to the original purchaser that this product is free from

defects in materials and workmanship for the period of 90 days from the date of purchase.

This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence

or accidents, repairs or alterations outside our facilities, criminal activity, improper installation,

normal wear and tear, or to lack of maintenance. We shall in no event be liable for death,

injuries to persons or property, or for incidental, contingent, special or consequential damages

arising from the use of our product. Some states do not allow the exclusion or limitation of

incidental or consequential damages, so the above limitation of exclusion may not apply to you.

THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR

IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation

charges prepaid. Proof of purchase date and an explanation of the complaint must accompany

the merchandise. If our inspection verifies the defect, we will either repair or replace

the product at our election or we may elect to refund the purchase price if we cannot readily

and quickly provide you with a replacement. We will return repaired products at our expense,

but if we determine there is no defect, or that the defect resulted from causes not within

the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also

have other rights which vary from state to state.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353

Tabla de contenidos

Otros manuales de Accesorios para automóviles de HAUL MASTER

HAUL MASTER

HAUL MASTER 64793 Instrucciones de montaje

HAUL MASTER

HAUL MASTER 94643 Manual de lista de piezas

HAUL MASTER

HAUL MASTER 62660 Instrucciones de montaje

HAUL MASTER

HAUL MASTER 92655 Instrucciones de montaje

HAUL MASTER

HAUL MASTER 96279 Manual de lista de piezas

HAUL MASTER

HAUL MASTER 92626 Manual de instalación

HAUL MASTER

HAUL MASTER 69650 Instrucciones de montaje

HAUL MASTER

HAUL MASTER 95408 Manual de usuario

HAUL MASTER

HAUL MASTER 95974 Manual de lista de piezas

HAUL MASTER

HAUL MASTER HAUL MASTER 98511 Manual de usuario

HAUL MASTER

HAUL MASTER 63924 Instrucciones de montaje

HAUL MASTER

HAUL MASTER 66983 Instrucciones de montaje

HAUL MASTER

HAUL MASTER 96462 Manual de instalación

HAUL MASTER

HAUL MASTER 98239 Manual de instalación

HAUL MASTER

HAUL MASTER 96198 Manual de usuario

HAUL MASTER

HAUL MASTER 94696 Manual de usuario

HAUL MASTER

HAUL MASTER 90018 Instrucciones de montaje

HAUL MASTER

HAUL MASTER 96406 Instrucciones de montaje

HAUL MASTER

HAUL MASTER 92174 Manual de lista de piezas

HAUL MASTER

HAUL MASTER 41005 Manual de usuario

HAUL MASTER

HAUL MASTER 500 LB. CAPACITY KNOCKDOWN CARGO CARRIER Manual de instalación

HAUL MASTER

HAUL MASTER 94564 Manual de usuario

HAUL MASTER

HAUL MASTER 96406 Manual de usuario

HAUL MASTER

HAUL MASTER 96658 Manual

Manuales populares de Accesorios para automóviles de otras marcas

James Baroud

James Baroud Odyssey Manual de usuario

Motorola

Motorola i50sx Manual de usuario

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manual de usuario

Feniex

Feniex T3 Manual de usuario

Renault

Renault 77 11 423 180 Manual de usuario

Kia

Kia E8300-4D000 Manual de usuario

Brink

Brink 756843 Manual de usuario

Whispbar

Whispbar K085W Manual de usuario

v.link

v.link CI-VL2-PC-HSD Manual de usuario

Viking

Viking Stack-Rack Guía de configuración rápida

Aries

Aries 203015 Manual de usuario

Choetech

Choetech AT0005 Manual de usuario

ZZ2

ZZ2 ZZAIR-PRO Manual de usuario

Holman

Holman 4A80L Manual de usuario

Thule

Thule 2075 Manual de usuario

Motorola

Motorola T325 Manual de usuario

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guía de instalación

DV8

DV8 FBJL-02 Manual de usuario