HARRICK ATC-024-1 Manual de usuario

www.harricksci.com

HARRICK SCIENTIFIC PRODUCTS, INC.

141 Tompkins Ave, 2nd floor •Pleasantville, NY 10570 •(800) 248-3847 •FAX (914) 747-7209

AUTOMATIC TEMPERATURE

CONTROLLER

USER’S MANUAL FOR ATC-024-1 and ATC-024-2

TABLE OF CONTENTS

ATC-M-07

General Information

Unpacking................................................................................................................................ 1

Technical Support.................................................................................................................... 1

Feedback.................................................................................................................................

The Temperature Controller

About the ATC ....................................................................................................................... 2

Environmental Conditiions ..................................................................................................... 2

Getting Ready.......................................................................................................................... 2

Connecting the ATC .............................................................................................................. 4

Single Loop Control

Setup Menus .......................................................................................................................... 5

Input Prompts ......................................................................................................................... 5

Global Prompts ....................................................................................................................... 6

Set Point ................................................................................................................................. 6

Auto-tuning ............................................................................................................................. 7

Double Loop Control

Setup Menus ........................................................................................................................... 8

Input Prompts.......................................................................................................................... 8

Global Prompts........................................................................................................................ 9

Set Point.................................................................................................................................. 10

Auto-tuning ............................................................................................................................. 10

Appendix A

Replacing the Fuses................................................................................................................ 13

Appendix B

Trouble Shooting.....................................................................................................................

GENERAL INFORMATION

1of 17

UNPACKING Before installing the automatic temperature controller (ATC)

make sure all the parts on the included check list are

present. If any parts are missing or damaged, contact

Harrick Scientific immediately.

TECHNICAL SUPPORT For additional information please contact our

Technical Support Center at 800-248-3847 between

9 a.m. and 5 p.m. EST; or e-mail your questions to:

techsupport@harricksci.com

FEEDBACK Your comments and suggestions are welcome. Please

send them to:

Harrick Scientific Products, Inc.

PO Box 277

141 Tompkins Ave, 2nd floor

Pleasantville, NY 10570

Phone: 800-248-3847; Fax: 914-747-7209

E-mail: [email protected]

Web: www.harricksci.com

THE TEMPERATURE CONTROLLER

2 of 17

ABOUT THE ATC™

The Automatic Temperature Controller (ATC) can be

manually programmed to reach a desired temperature or

computer controlled for sophisticated temperature

profiling. The controller automatically determines the best

settings for optimal heating based on the thermal

response of a particular system. It features two

thermocouple inputs and one 24V heater output, allowing

regular or cascade operation. Regular or single loop

control is used for accessories with only a sample

thermocouple. Accessories equipped with a sample and

heater thermocouple use cascade or double loop control.

Cascade control minimizes damage to system

components, allows for over sizing heaters for optimal

heat-up rates and extends heater life by reducing thermal

cycling of the heater.

This manual contains only “quick start” instructions. For

detailed instructions see the included Watlow manuals.

ENVIRONMENTAL

CONDITIONS The Automatic Temperature Controller (ATC) is intended

for use in light industrial and laboratory environments.

GETTING READY Familiarize yourself with the temperature controller by

referring to Figures 1, 2 and 3.

Figure 1 • Temperature Controller Front View

Heater

ON/OFF

Switch

Heater

Connector

Controller

ON/OFF

Switch

THE TEMPERATURE CONTROLLER

3 of 17

Figure 2 • Temperature Controller Back View

Figure 3 • Front Panel Detail

Power

Outlet

Connector TC1

Connector TC2

Lower

display

Upper

display

Up/Down

Arrow

Keys

DSPY key Mode Key

THE TEMPERATURE CONTROLLER

4 of 17

CONNECTING THE ATC To connect the temperature controller to the accessory:

•Check to make sure that all the switches on the

temperature controller are off (Figure 1).

•Plug in the AC line cord into the unit and into a

suitable AC outlet (Figure 2).

•If your accessory has only one thermocouple,

connect the thermocouple to the connector

labeled TC1 on the back of the temperature

controller.

•If your accessory has two thermocouples,

connect the heater thermocouple to the

connector labeled TC2 on the back of the

temperature controller and the sample

thermocouple to TC1.

•Connect the heater to the heater connector

located on the front of the temperature controller.

SINGLE LOOP CONTROL

5 of 17

When using the ATC with accessories equipped with one thermocouple, the temperature

controller should be programmed as follows:

•

Turn on the power to the controller (Figure 1),

leaving the power to the heaters turned off.

SETTING THE

THERMOCOUPLE TYPE

•

Simultaneously press both the Up-arrow Sand

the Down-arrow Tkeys for approximately 3

seconds until the Input Menu prompt InPt

appears in the upper display and the Setup Menu

prompt SEt appears in the lower display:

InPt / SEt

NOTE: The controller has four Setup Menus: Input, Output,

Global and Communications. Use the Up-arrow Sand

the Down-arrow Tkeys to select a menu and the MODE

key to step through the menu prompts.

Pressing the DSPY key (Figure 3) returns the controller to

the display Loop from any prompt in the menu.

•

Press the MODE key. In1 will appear in the

lower display.

•If the upper display does not show an H, the

symbol for the K-type thermocouple used in most

Harrick accessories, press the Up-arrow Skey

until it does. If the item to be heated does not

use a K-type thermocouple, please see the

Watlow manual for the correct setting.

•Press the DSPY key to return to the main display

format.

CAUTION:

Changing the value of ln1 changes most other prompts to the factory default values.

Document all settings before changing sensor type. Verify the correct sensor type before

making a change.

SINGLE LOOP CONTROL

6 of 17

SETTING THE CONTROL

TYPE

•

Simultaneously press both the Up-arrow Sand

the Down-arrow Tkeys for approximately 3

seconds until the Input Menu prompt InPt appears

in the upper display and the Setup Menu prompt

SEt appears in the lower display:

InPt / SEt

•Press the Up-arrow Skey twice. 9LbL appears

in the upper display:

9LbL/ SEt

•Press the MODE key four times. Cntl will appear

in the lower display.

•Press the Up-arrow Skey until nor appears in the

upper display.

•Press the DSPY key to return to the main display

format.

SETTING THE UNITS Make sure that this step is performed prior to setting the

low or high temperature limits.

•Simultaneously press both the Up-arrow Sand

the Down-arrow Tkeys for approximately 3

seconds until the Input Menu prompt InPt appears

in the upper display and the Setup Menu prompt

SEt appears in the lower display:

InPt / SEt

•Press the Up-arrow Skey twice. 9LbL appears

in the upper display:

9LbL/ SEt

•Press the MODE key once. C_F will appear in the

lower display.

•Either Ffor Fahrenheit units or Cfor Centigrade

units appears in the upper display.

•If the incorrect units are shown, press the Up-

arrow Sonce to change to the temperature units.

•Press the DSPY key to return to the main display

format.

SETTING THE LOW

TEMPERATURE LIMIT For routine operation, the low temperature limit for

thermocouple 1 (TC1) should be set to -200ºC, as follows:

•Make sure that the units have been set to

Centigrade, as described above.

•Simultaneously press both the Up-arrow Sand

the Down-arrow Tkeys for approximately 3

seconds until the Input Menu prompt InPt appears

in the upper display and the Setup Menu prompt

SEt appears in the lower display:

InPt / SEt

•Press the MODE key twice. rL1 will appear in the

lower display.

•Use the Down-arrow Tkey to set the upper

display to -200.

•Press the DSPY key to return to the main display

format.

SINGLE LOOP CONTROL

7 of 17

SETTING THE HIGH

TEMPERATURE LIMIT For routine operation, the low temperature limit for

thermocouple 1 (TC1) should be set to 750ºC, as follows:

•Make sure that the units have been set to

Centigrade, as described above.

•Simultaneously press both the Up-arrow Sand

the Down-arrow Tkeys for approximately 3

seconds until the Input Menu prompt InPt appears

in the upper display and the Setup Menu prompt

SEt appears in the lower display:

InPt / SEt

•Press the MODE key three times. rH1 will appear

in the lower display.

•Use the Up-arrow Sand/or Down-arrow Tkeys

to set the upper display to 750.

•Press the DSPY key to return to the main display

format.

Note For operation of the HVC-DRP-4 and HVC-VUV-4 diffuse

reflection reaction chambers at or near their high

temperature limit, set the high temperature limit to 1000.

SETTING THE LOW POWER

LIMIT For routine operation, the low power limit should be set to

0%, as follows:

•Simultaneously press both the Up-arrow Sand

the Down-arrow Tkeys for approximately 3

seconds until the Input Menu prompt InPt appears

in the upper display and the Setup Menu prompt

SEt appears in the lower display:

InPt / Set

•Press the Up-arrow Skey twice. 9LbL appears

in the upper display:

9LbL/ SEt

•Press the MODE key eight times. LoP will appear

in the lower display.

•Use the Down-arrow Tkey to set the low power

limit, shown in the upper display, to 0.

•Press the DSPY key to return to the main display

format.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Controladores de temperatura de otras marcas

Swegon

Swegon LUNAd MB Manual de usuario

Lucky Reptile

Lucky Reptile Thermo Control II Manual de usuario

SENSORMETRIX

SENSORMETRIX Argon 100 Manual de usuario

Fuji Electric

Fuji Electric PXE4 Manual de usuario

Yuyao gongyi

Yuyao gongyi XMT-808 series Manual de usuario

Selec

Selec TC544C Manual de usuario

P.W. KEY

P.W. KEY rt-208gt Manual de usuario

Future Design

Future Design FDC-9200 Manual de usuario

BH Thermal

BH Thermal BriskONE Manual de usuario

Omron

Omron E5EX-H Manual de usuario

West Control Solutions

West Control Solutions KS 45 Guía de inicio rápido

MCS

MCS RITC-15B Manual de usuario

SMC Networks

SMC Networks Thermo-con INR-244-639 Manual de usuario

eltherm

eltherm Ex-TC It Series Manual de usuario

Omron

Omron C200H-TV Series Manual de usuario

industrie technik

industrie technik CA1 Manual de usuario

KRAL

KRAL EET 32 Manual de usuario

dixell

dixell XR420C Diagrama de cableado