Harman Kardon AVR 2650 Manual de usuario

Audio/video receiver

AVR 3650, AVR 365, AVR 2650, AVR 265

Quick-Start Guide

Introduction, Speaker Placement and Connection

AVR

Introduction

Thank you for choosing a harman kardon product!

This quick-start guide contains all the information you need to connect and set up your

new harman kardon audio/video receiver.

To conserve our natural resources, your receiver does not include a printed owner's

manual. An owner's manual containing complete information about operating all of your

new receiver’s features is available at our Web site. Go to www.harmankardon.com and

download the AVR 3650, AVR 365, AVR 2650, AVR 265 Owner’s Manual.

Place the Receiver

• Place the receiver on a rm and level surface. Be certain that the surface and any mounting

hardware can support the receiver’s weight.

• Provide proper space above and below the receiver for ventilation. If you install the receiver

in a cabinet or other enclosed area, provide cooling air within the cabinet. Under some

circumstances, a fan may be required.

• Do not obstruct the ventilation slots on the top of the receiver or place objects directly

over them.

• Do not place the receiver directly on a carpeted surface.

• Do not place the receiver in moist or humid locations, in extremely hot or cold locations, in

areas near heaters or heat registers, or in direct sunlight.

Connections

Place Your Speakers

Determine the locations for your system’s speakers according to their manufacturer’s

directions and the layout of your listening room. Use the illustrations below as a guide

for 7.1-channel and 5.1-channel systems.

Speaker Positioning for Speaker Positioning for

7.1-Channel Systems 5.1-Channel Systems

For more detailed speaker placement information, including the use of front

height speakers, download the complete AVR 3650, AVR 365, AVR 2650, AVR 265

Owner’s Manual from www.harmankardon.com.

CAUTION: Before making any connections to the audio/video receiver, ensure that

the receiver’s AC cord is unplugged from the receiver and the AC outlet. Making

connections with the receiver plugged in and turned on could damage the speakers.

Speaker

Connectors

HDMI®

Connectors

Analog Audio

Connectors

Network

Connector

Subwoofer

Connector

AC Input

Connector

Main Power

Switch

Radio Antenna

Connectors

Digital Audio

Connectors

Analog Video

Connectors

The Bridge IIIP

Connector

Rear-Panel Connection (AVR 3650 shown)

Note: Silkscreening and connectors will vary for different models.

Not all connectors shown will be present on all models.

Connections

AVR

Connect Your Speakers

How to use the AVR speaker terminals:

Always connect the colored (+) terminal on the AVR to the (+) terminal on the speaker

(usually red), and the black (–) terminal on the AVR to the (–) terminal on the speaker

(usually black).

IMPORTANT: Make sure the ( + ) and ( – ) bare wires do not touch each other or the

other terminal. Touching wires can cause a short circuit that can damage your receiver

or amplier.

Connect the speakers as shown in the illustration.

Connect Your Subwoofer

Use a single RCA audio cable to connect the receiver’s Subwoofer Pre-Out connector to

your subwoofer. Consult your subwoofer’s user manual for specic information about

making connections to it.

Connect Your TV or Video Display

If your TV has an HDMI connector: Use an HDMI cable (not included) to connect

it to the receiver’s HDMI Monitor Out connector. You do not need to make any other

connections to your TV from the receiver or from any of your video source components.

If your TV does not have an HDMI connector: Use a composite video cable (not

included) to connect the receiver’s Composite Monitor Out connector to your TV’s

composite video connector.

Note: The HDMI connection to your TV is preferred. If you use the composite video

connection to your TV, you will not be able to view the receiver’s on-screen menus.

1. Unscrew Cap 2. Insert Bare Wire 3. Tighten Cap

Receiver

Subwoofer

Connector

Powered

Subwoofer

Single

RCA Audio Cable

(not supplied)

Receiver

HDMI Monitor Out

Connector

HDMI Cable

(not supplied)

Receiver

Composite

Monitor Out

Connector

Composite Video Cable

(not supplied)

Connections

AVR

AVR Input Connector Connected Component Default Source Button Assigned Source Button

HDMI 1

HDMI 2 Cable/Sat

Game

Media Server

Aux

A (red)

B (green)

C (yellow)

D (green)

B (green)

C (yellow)

D (green)

A (red)

Blu-ray

HDMI 3

HDMI 4

HDMI 5

(AVR 3650/AVR 365 only)

HDMI Front

Component Video 1

Component Video 2

Composite Video 1

Composite Video 2

Optical Digital Audio 1

Optical Digital Audio 2

Coaxial Digital Audio Input 1

Coaxial Digital Audio Input 2

Analog Audio In 1

Analog Audio In 2

Analog Audio In 3

Monitor Output Connector

Record Output Connector

Connected Component

HDMI Monitor Out

Composite Video Monitor Out — — — —

— — — —

— — — —— — — —

— — — —

Composite Video Rec Out

Optical Digital Audio Out

Input Connections and Assigned Source Buttons

Connect Your Audio and Video Source Devices

Source devices are components where a playback signal originates, e.g. a Blu-ray Disc™

or DVD player; a cable, satellite or HDTV tuner; etc. Your receiver has several different

types of input connectors for your audio and video source devices: HDMI, component

video, composite video, optical digital audio, coaxial digital audio and analog audio.

The connectors are not labeled for speciﬁc types of source devices; they are labeled

numerically, so you can connect your devices according to your individual system’s

make-up.

Your receiver’s various source buttons have default assignments to different input

connectors (listed in the “Default Source Button” column of the table below). For ease of

setup, you should connect each source device to the connector where the corresponding

default source button is assigned (e.g., connect your Blu-ray Disc player to HDMI 1).

However, you can connect your source devices as you wish and re-assign any of the

source buttons to any of the input connectors listed in the table according to where you

actually connect each of your source devices.

As you connect your various source components, ﬁll out the “Connected Component”

column in the table – it will make it easier for you to assign the various source buttons

after you have completed making all of the connections. (You will make any changes to

the source-button assignments and ﬁll in the “Assigned Source Button” column later in

the setup process.)

HDMI Devices

If any of your source devices have HDMI connectors, using them will provide the best

possible video and audio performance quality. Since the HDMI cable carries both

digital video and digital audio signals, you do not have to make any additional audio

connections for source devices you connect via HDMI connectors.

Note: If you have a TV or other source device equipped with the HDMI Audio Return

Channel Function, you can feed its sound to the AVR via the HDMI Monitor Out

connection’s Audio Return Channel, and it will not require additional audio connections

to the AVR. Refer to the complete AVR 3650, AVR 365, AVR 2650, AVR 265 Owner’s

Manual, downloadable at www.harmankardon.com.

Component Video Devices

If any of your video source devices have component video connectors (and do not have

HDMI connectors), using the component video connectors will provide superior video

performance. You will also need to make an audio connection from the source device

to the receiver.

Composite Video Devices

Use composite video connectors for video source devices that don’t have HDMI or

component video connectors. You will also need to make an audio connection from the

source device to the receiver.

Optical digital audio devices

If your non-HDMI source devices have optical digital outputs, connect them to the

receiver’s optical digital audio connectors. NOTE: Make only one type of digital

connection (HDMI, optical or coaxial) from each source device.

Coaxial digital audio devices

If your non-HDMI source devices have coaxial digital outputs, connect them to

the receiver’s coaxial digital audio connectors. NOTE: Make only one type of digital

connection (HDMI, optical or coaxial) from each source device.

AVR

Connections

Receiver

HDMI Connectors

HDMI-Equipped

Source Device

HDMI Cable

(not supplied)

To HDMI

Output

Receiver

Video Connectors

Component Video-Equipped

Source Device

Component Video

Cable (not supplied)

To Component Video

Outputs

Receiver

Video Connectors

Composite Video-Equipped

Source Device

Composite Video

Cable (not supplied)

To Composite Video

Output

Receiver

Digital Audio Connectors

Optical-Equipped

Source Device

Optical Digital Audio

Cable (not supplied)

To Optical Digital Audio

Output

Receiver

Digital Audio Connectors

Coaxial-Equipped

Source Device

Coaxial Digital Audio

Cable (not supplied)

To Coaxial Digital Audio

Output

Connections

AVR

Analog Audio Devices

Use the receiver’s analog audio connectors for source devices that don’t have HDMI or

digital audio connectors.

Audio Recorders

Connect a digital audio recorder’s optical digital input to the receiver’s optical digital

output. You can record both coaxial and optical digital input signals.

Connect an analog audio recorder’s inputs to the receiver’s analog audio Rec Out

connectors. You can record any analog audio input signal.

Video Recorders

Connect an analog video recorder’s video input connector to the receiver’s composite

video Rec Out connector. You can record any composite video signal. NOTE: To record

the audio and video from the source device, connect the receiver’s analog audio Rec Out

connectors to the analog video recorder’s audio inputs.

Receiver Analog Video

Recorder Connectors

Receiver Analog Audio

Recorder Connectors

Analog Video

Recording Device

Analog Audio/Video

Cable (not supplied)

To Analog Audio/Video

Record Inputs

Receiver

Digital Audio Recorder Connector

Digital

Recording Device

Optical Digital Audio

Cable (not supplied)

To Optical Digital

Record Input

Receiver

Analog Audio Recorder Connectors

Analog

Recording Device

Stereo Audio

Cable (not supplied)

To Stereo Analog Record

Inputs

Receiver

Analog Audio Connectors

Analog

Source Device

Stereo Audio

Cable (not supplied)

To Stereo Analog Audio

Output

Connections

AVR

Connect The Bridge IIIP

Connect an optional The Bridge IIIP to the receiver’s The Bridge IIIP connector. Insert the plug all

the way until it snaps into place in the connector. IMPORTANT: Connect The Bridge IIIP only

with the receiver’s power turned OFF.

Connect Your Local Area Network

Use a Cat. 5 or Cat. 5E cable (not supplied) to connect the receiver’s Network connector to your

home network to enjoy Internet radio and content from DLNA®-compatible devices that are

connected to the network.

Connect the Radio Antennas

• Connect the supplied FM antenna to the receiver’s FM 75Ωantenna connector. For the best

reception, extend the FM antenna as far as possible.

• Bend and fold the base of the supplied AM antenna as shown and connect the antenna wires

to the receiver’s AM and Gnd connectors. (You can connect either wire to either connector.)

Rotate the antenna as necessary to minimize background noise.

NOTE: To connect an optional SIRIUS Connect™ home tuner (AVR 3650 and AVR 2650 only),

RS-232, multi-zone, remote IR and trigger equipment, please download the AVR 3650, AVR

365, AVR 2650, AVR 265 Owner’s Manual from www.harmankardon.com.

Connect to AC Power

Connect the AC power cord to the receiver’s AC Input connector and then to a working,

non-switched AC power outlet.

Receiver

The Bridge IIIP

Connector

The Bridge IIIP

Internet

and LAN

Receiver

Network

Connector

Network

Modem

Cat. 5/5E Cable

(not supplied)

FM Antenna

(supplied)

AM Antenna

(supplied)

Bend and fold base

Receiver

Antenna

Connectors

Receiver

AC Input

Connector

AC Power

Outlet

Power Cord

(supplied)

Set Up the Receiver

Install the Batteries in the Remote Control

Remove the remote control’s battery cover, insert the four supplied AAA batteries as shown in

the illustration, and replace the battery cover.

NOTE: Remove the protective plastic from the receiver’s front panel so it doesn’t reduce

the remote control’s effectiveness.

Turn On the Receiver

1. Set the rear-panel Main Power switch to “On.” (The front-panel Power indicator will

glow amber.)

2. Press the front-panel Power button.

Configure Your Speakers

1. Plug the supplied EzSet/EQ™ microphone into the receiver’s Headphone connector.

2. Place the microphone at ear height in your listening position.

3. Turn on your TV and select the TV input where you connected the receiver in Connect

Your TV, on page 3.

4. Press the remote control’s Setup button. The receiver’s on-screen display (OSD) setup

menu will appear on the TV. (Note: If you have used a composite video connection to

your TV, the OSD menus will not appear on your TV. Follow the steps below using the

receiver’s front-panel display.)

5. Use the remote’s arrow and OK buttons to select “Speaker Setup.”

6. Select “Automatic Setup – EzSet/EQ.”

7. Select “Continue.”

8. Follow the instructions that appear on the screens.

Assign the Receiver’s Source Buttons

1. Review the input connections you listed on the Input Connections and Assigned

Source Buttons table, on page 4. Note what changes (if any) you want to make from the

default source-button assignments that appear on the list.

2. Turn on your TV and select the TV input where you connected the receiver in Connect

Your TV, on page 3.

3. Press the remote control’s Setup button. The receiver’s on-screen display (OSD) setup

menu will appear on the TV. (Note: If you have used a composite video connection to

your TV, the OSD menus will not appear on your TV. Follow the steps below using the

receiver’s front-panel display.)

AVR Connections

Main Power

Switch

Power

Button

EzSet Microphone

(supplied)

Receiver

Headphone

Connector

Source Select

Select the Source Device to Enjoy

Setup Source

Setup Source Devices Connected to the AVR

Speaker Setup

Speaker Optimization, EQ

Zone 2

Manage and Control Zone 2

System

General AVR Settings

Automatic Setup – EzSet/EQ

Automated Speaker Setup and EQ

Manual Setup

Manually Adjust Speaker Settings

Speaker Setup

AVR Connections

4. Use the remote’s arrow and OK buttons to select “Setup Source,” and select a source button

that you want to re-assign from the list that appears. Press the OK button.

5. Select “Video Input From Source” and select the video input connector you want to

assign to the source button. Press the OK button. (The setup menu will disappear from

the TV.)

6. Press the remote control’s Setup button again. The receiver’s on-screen display

(OSD) setup menu will reappear on the TV. (Note: If you have used a composite video

connection to your TV, the OSD menus will not appear on your TV. Follow the steps below

using the receiver’s front-panel display.)

7. Use the remote’s arrow and OK buttons to select “Setup Source,” and select the

source button whose video input you just re-assigned.

8. Select “Audio Input from Source” and select the audio input connector you want to

assign to the source button. Press the OK button.

9. Press the remote’s Back/Exit button and repeat steps 3 – 8 for the remaining source

buttons you want to re-assign.

You are now ready to enjoy your receiver!

IMPORTANT: For complete information about using all of your audio/video

receiver’s features and capabilities, download the AVR 3650, AVR 365, AVR 2650,

AVR 265 Owner’s Manual from www.harmankardon.com.

Source Select

Select the Source Device to Enjoy

Setup Source

Setup Source Devices Connected to the AVR

Speaker Setup

Speaker Optimization, EQ

Zone 2

Manage and Control Zone 2

System

General AVR Settings

Source Select

Select the Source Device to Enjoy

Cable/Sat

Blu-ray

Bridge

USB

SIRIUS Radio

FM Radio

AM Radio

Game

Media Server

Setup Source

Setup Source Devices Connected to the AVR

Speaker Setup

Speaker Optimization, EQ

Zone 2

Manage and Control Zone 2

System

General AVR Settings

Cable/

Sat

Cable/Sat

Audio Effects

Video Modes:

Surround Modes:

Off

Auto Select

720p – 60Hz

No Input

Off

Cable/Sat

NO AUDIO INPUT

HDMI 2

HDMI 1

HDMI 2

HDMI 3

HDMI 4

HDMI 5

HDMI Front

Component 1

Component 2

Composite 1

Composite 2

Audio Format from Source:

Video Input from Source:

Audio Input from Source:

Change Name:

Adjust Lip Sync

Resolution to Display:

Resolution from Source:

HDMI Bypass:

Cable/Sat

Audio Effects

Video Modes:

Surround Modes:

Off

Auto Select

720p – 60Hz

No Input

Off

Cable/Sat

NO AUDIO INPUT

Component 1

Analog 1

HDMI 1

HDMI 2

HDMI 3

HDMI 4

HDMI 5

HDMI Front

Optical 1

Optical 2

Coaxial 1

Coaxial 2

Analog 1

Audio Format from Source:

Video Input from Source:

Audio Input from Source:

Change Name:

Adjust Lip Sync

Resolution to Display:

Resolution from Source:

HDMI Bypass:

HARMAN Consumer, Inc.

8500 Balboa Boulevard, Northridge, CA 91329 USA

516.255.4545 (USA only)

Made in P.R.C.

harman kardon is a trademark of HARMAN International Industries, Incorporated, registered in the United States and/or other coun-

tries. EzSet/EQ is a trademark of HARMAN International Industries, incorporated. DLNA is a registered trademark of the Digital Living

Network Alliance. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI

Licensing LLC in the United States and other countries. SIRIUS, SIRIUS Connect and all related marks and logos are trademarks of

SIRIUS XM Radio inc., and its subsidiaries.

Features, specifications and appearance are subject to change without notice. www.harmankardon.com

Otros manuales para AVR 2650

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Receptor de Harman Kardon

Harman Kardon

Harman Kardon AVR 1510 Manual de usuario

Harman Kardon

Harman Kardon AVR 1650 Manual de usuario

Harman Kardon

Harman Kardon AVR2000RDS Manual de usuario

Harman Kardon

Harman Kardon AVR200 Manual de usuario

Harman Kardon

Harman Kardon AVR 7300 Manual de usuario

Harman Kardon

Harman Kardon AVR 4000 Manual de usuario

Harman Kardon

Harman Kardon AVR 7000 Manual de usuario

Harman Kardon

Harman Kardon AVR 100 Manual de usuario

Harman Kardon

Harman Kardon AVR 435 Manual de usuario

Harman Kardon

Harman Kardon AVR 2650 Manual de usuario

Harman Kardon

Harman Kardon DPR 1001 Manual de instrucciones

Harman Kardon

Harman Kardon AVR 7300 Manual de usuario

Harman Kardon

Harman Kardon AVR 430 Manual de usuario

Harman Kardon

Harman Kardon KARDON AVR 360 Manual de usuario

Harman Kardon

Harman Kardon BDS 5 SO Manual de usuario

Harman Kardon

Harman Kardon AVR 745 Manual de usuario

Harman Kardon

Harman Kardon Stratophonic SR300B Manual de usuario

Harman Kardon

Harman Kardon AVR 354 Manual de usuario

Harman Kardon

Harman Kardon 900+ Manual de usuario

Harman Kardon

Harman Kardon AVR 445 Manual de usuario

Harman Kardon

Harman Kardon 230A Manual de usuario

Harman Kardon

Harman Kardon AVR 145 Manual de usuario

Harman Kardon

Harman Kardon AVR 630 Manual de usuario

Harman Kardon

Harman Kardon AVR 146 Instrucciones y recetas

Manuales populares de Receptor de otras marcas

Garmin

Garmin GA 23 Manual de usuario

Aiphone

Aiphone PS-12F Manual de usuario

IMES

IMES TCS-01CA-PMI Manual de usuario

BWI Eagle

BWI Eagle AIR-EAGLE SR Manual

AMIMON

AMIMON AMN12310 WHDI Manual de usuario

Dual

Dual DMCPA79BT Instrucciones de funcionamiento

Sound Associates

Sound Associates SA652P Manual de usuario

Sherwood

Sherwood NewCastle R-772 Manual de usuario

Audio

Audio A10-RX Series Manual de usuario

AllSee

AllSee PushShare PSRV1.1 Manual de usuario

DEMAG

DEMAG DRC-DR D2 Manual de usuario

Teleco

Teleco TVRCL868A02 Manual de usuario

Bosch

Bosch RF3222E Manual de usuario

Kramer

Kramer 631R Manual de usuario

Xpress

Xpress xmc10 Manual de usuario

JVC

JVC KD-MR1BTS Manual de usuario

Omega Engineering

Omega Engineering UWTC-REC3 Manual de usuario

e-survey

e-survey E300 Pro Manual de usuario