Harison DISCOVER 1049 Manual de usuario

Operation Manual

Catalogue

Key Knowledge for Safety.................................................................................................... 1

Assembly Drawing...........................................................................................................2-3

List of Spare Parts............................................................................................................4-5

Assembly Instructions.....................................................................................................6-22

Training Guidance.............................................................................................................23

Chart of Training Guidance............................................................................................24-25

Warning........................................................................................................................26

Key Knowledge for Safety

Please keep this manual well for future reference.

Matters to be attended:

There are some safety precautions to be followed during the operation although the safety

considerations have been taken into consideration in the design and manufacture of this training

machine. Please read this manual carefully before assembling and using the training machine,

especially the following safety precautions:

1. 1.Keep the children and pets away from the training machine, and do not leave any

unattended child alone in the room where the training machine is placed.

2. Only one person is allowed to use the training machine at the same time.

3.Any user who feeling dizziness, nausea, chest tightness or other uncomfortable symptom

shall stop the training immediately and visit a doctor thereafter.

4. The training machine shall be placed on a clean and flat surface, and shall be not used at

any place near the water source or outdoor.

5.Hands shall be not close to any transmission parts when using.

6.Users are required to dress appropriately for training when using the training machine and

no loose or other types of clothing that may get stuck during training is allowed. Users are also

recommended to wear sneakers or healthcare shoes during training.

7.The training shall be carried out only in the way described in the instructions during the use

of the training machine , and no training shall be carried out in any manner outside the

instructions.

8.Any object with with a sharp point around the training machine is not allowed.

9.No disabled person shall use the training equipment without the supervision of a training

partner or a caregiver.

10.Usually, users are required to warm up before training through a variety of stretching

exercises.

11. No use is allowed upon any abnormality of the training machine

12.Training records shall be kept during the training process.

13.The maximum user weight of this product is 120KG.

14.The maximum allowable weight of this product to hold is 72KG (with weights).

15.The general safety standard of this product is: GB17498.1-2008/GB17498. 2-2008.

Warning:

It is especially important for users who are over the age of 35 or has medical records to

consult a doctor before training. Please read all instructions carefully before using any fitness

equipment. We will not be responsible for any injury caused by the user themselves.

Assembly Drawing

List of Spare Parts

A- List of Spare Parts

Item Desc.& Spec. Qty. Item Desc.& Spec. Qty.

1 Rear bottom tube assembly 1 53 50 Circular tube plug 6

2 Floor tube assembly 1 54 Spherical circular tube plug 1

3 Front floor tube assembly 1 55 Tube lining 3

4 Pedal 1 56 25 Circular tube plug 8

5 Counterweight guide rod weldment 2 57 Plastic sleeve 2

6 Front inclined tube assembly 1 58 Forward cushion 1

7 Front strain-frame supporting tube

assembly

1 59 Circular tube sleeve 4

8 Limiting tube assembly 1 60 38 square tube plug 1

9 Shield connection plate 1 2 61 Adjusting rod flat gasket 3

10 Weight adjusting rod assembly 1 62 Cylindrical pin 1

11 Shield connection plate 2 2 63 L-shape bolt 1

12 Top beam assembly 1 64 Core pulling rivet 4

13 Cantilever assembly 1 65 Shackle 7

14 Limiting tube assembly 1 66 Eight-ring chain 3

15 U-seat connecting tube assembly 1 67 Shaft 1

16 Kick assembly 1 68 Pulley pressing sleeve(large) 4

17 Hand pad assembly 1 69 Pulley pressing sleeve(small) 16

18 Right arm swinging assembly 1 70 Pan head square neck bolt(M10*90) 6

19 Forward pushing handle assembly 2 71 Pan head square neck bolt(M10*65) 2

20 Left arm swinging assembly 1 72 Hexagonal socket head bolt 4

21 Pulley connection plate 2 73 Hexagon bolt (M10*135) 2

22 Double U-seat weldment 1 74 Hexagon bolt (M10*90) 4

23 Rotary U-seat 1 75 Hexagon bolt (M10*65) 8

24 Sponge stick tube 2 76 Hexagon bolt (M10*45）11

25 Iron-net protective cover 2 77 Hexagon bolt (M10*20) 4

26 High tension handlebar tube assembly 1 78 Hexagonal socket head bolt

(M10*12)

27 Low tension handlebar tube assembly 1 79 Hexagon bolt (M10*40) 2

28 Arm swinging U-seat assembly 2 80 Hexagon bolt (M8*65）2

29 High tension sleeve weldment 1 81 Hexagon bolt (M8*15) 2

30 Weight heads 1 82 Cross recess pan head screw

(M6*20)

31 Weight 11 83 Hexagon bolt M8*25 2

32 High tension wire assembly 2 84 Locknut（M16) 2

33 Butterfly arm wire assembly 1 85 Locknut（M10) 38

34 Seat cushion component 1 86 Big flat gasket (D16) 2

35 Back cushion component 1 87 Flat gasket（D10) 72

36 Hand pad component 1 88 Flat gasket（D8) 10

37 Small elastic pin knob 2 89 Locknut M8 3

38 Training rope assembly 1 90 Hexagon bolt (M10*95）1

39 Round tape assembly 1 91 Nut cap (M16) 2

40 Big sponge stick 2 92 High tension PVC sleeve 2

41 Sponge stick 4 93 Back cushion adjusting tube l

42 Sponge grip 6 94 Spacer bush 2

43 Elastic pin knob 2 95 PVC plastic sleeve 2

44 Shock pad 2 96 Top tube connection weldment 1

45 Kick cushion 1 97 Pulley yoke weldment 1

46 Pulley 18 98 Handle wire assembly (2800mm) 1

47 Outer foot strap 4 99 Spacer tube 1

48 Weight head bush 1 100 Hexagon bolt (M12*90）1

49 50* 50 rectangular tube plug 4 101 Flat gasket (D12) 1

50 25* 50 rectangular tube plug 4 102 Handle component 1

51 50 square tube plug 2 103 Hexagonal socket head bolt (M8*35) 1

52 25 circular tube plug 4 104

Tool

Spanner 13, 14 and 17 2 Allen wrench 6# 2

Special spanner 1 Allen wrench 5# 1

B- List of Spare Parts

Item Desc.& Spec. Qty. Item Desc.& Spec. Qty.

l Parallel bars lower supporting frame 1 14 Hexagon bolt (M10*70) 2

2 Parallel bars upper supporting frame 1 15 Hexagon bolt (M10*20) 4

3 Parallel bars left arm-resting tube 1 16 Square neck pan bolt (M10*70) 2

4 Parallel bars right arm-resting tube 1 17 Hexagon bolt (M8*70) 2

5 Arm-resting standpipe 2 18 Hexagon bolt (M8*65）4

6 Backrest assembly 1 19 Hexagon bolt (M8*25) 2

7 Hand pad assembly 2 20 Flat gasket（D10）14

8 Handle grip (D25) 4 21 Flat gasket（D8) 8

9 Circular tube plug (D25) 6 22 Locknut（M10）6

10 Hollow plug 2 23

11 25* 50 rectangular tube plug 1 24

12 50 square tube plug 1 25

13 Hexagon bolt (M10*95）2 26

Assembly Instructions

Installation Instructions for Body Section(A)

Important: Please make sure that all the accessories are complete after unpacking.

Remark: It is better for two or more people to assemble together during the assembly process to

avoid any injury.

Step1

1.Place the rear bottom tube assembly (1) and floor tube assembly (2) as shown in the figure

and secure them with M10*90 pan head square neck bolt (70), D10 flat gasket (87) and M10

locknut (85).

2. Insert the counterweight guide rod weldment (5) into the hole corresponding to the rear

bottom tube assembly (1), and lock it from the bottom with M10*20 hexagon bolt (77) and D10

flat mat (87) after fitting.

3. Place the floor tube assembly (2) and the front floor tube assembly (3) as shown in the

figure and secure them with M10*90 hexagon bolt (74), D10 flat gasket (87) and M10 locknut

(85).

4. Fix the limiting tube (8) through the pedal (4) as shown on the front floor tube assembly (3)

and then cover both ends of the limiting tube (8) with a D25 circular tube plug (56).

Step2

1.Place the front inclined tube assembly (6) on the assembled floor tube assembly (2) as

shown in the figure and secure it with M10*65 pan head square neck bolt(71), D10 flat gasket (87)

and M10 locknut (85).

2.Place the front bottom bracket support tube assembly (1) and the front inclined tube

assembly (6) as shown in the figure and secure them with M10*90 pan head square neck bolt (70),

D10 flat gasket (87) and M10 locknut (85).

Step3

1.First, load the shock pad (44) and the weight (31) into the counterweight guide rod

weldment (5) as shown in the figure, them insert it in the direction shown. Lead the cylindrical

pin(62) through the first hole (from top to bottom) of the weight head bush (48) and the weight

adjusting rod assembly (10), and then install the weight head assembly (30). At last, place the

adjusting rod flat gasket (61) in the position shown in the figure.

Tabla de contenidos

Otros manuales de Equipo de fitness de Harison

Harison

Harison HR-407 Manual de usuario

Harison

Harison HR-408 Manual de usuario

Manuales populares de Equipo de fitness de otras marcas

NSD

NSD PB-188P Manual de usuario

Performance

Performance HyperVibe Manual de usuario

Scalamobil

Scalamobil S27 Manual de usuario

Precor

Precor Experience Series Manual de usuario

FYTTER

FYTTER RedMIUM BENCH BE-T6R Manual de usuario

Taurus

Taurus TF-RK1312 Manual de usuario

Nustep

Nustep T5 Manual de usuario

Precor

Precor CW-507 Manual de usuario

Movement

Movement BICEPS Idea Manual de usuario

Kegel8

Kegel8 V For Men Manual de usuario

Skandika

Skandika Styrke II Manual de usuario

BLK BOX

BLK BOX 21-0122-0B Manual de usuario

Stamina

Stamina aeropilates premier 299 Manual de usuario

SPORTSTECH

SPORTSTECH PBX300 Manual de usuario

ParaBody

ParaBody Serious Steel 877102 Manual de usuario

Weslo

Weslo Gym 650 Manual de usuario

Rebel

Rebel ACTIVE RBA-1011 Manual de usuario

4iiii

4iiii FLiiiight Manual de usuario